Question about 2002 kawasaki KLX 250

1 Answer

Klf 250 want start on starter motor, starter is turning but won't engage.

Its a klf 250 farm quad,it starts with the pull start,but when we press the starter button the starter is turning,but the starter is not engaging.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • kawasaki Master
  • 1,190 Answers

Stuck starter gear spring ! inside clutch cover !

Posted on Mar 29, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Starting fault

There is also a safety switch on the clutch lever that could give the same symptoms.
Another thing to check is the fuse block that has a starter relay built in (hidden) above the fuse compartment. My D5 has the same symptoms and this is the problem. If I keep the starter button depressed for some seconds the relay operates and bike starts.

Posted on Mar 19, 2010

  • 39 Answers

SOURCE: 2001 kawasaki bayou 220 my quad died in the middle

try to charge your battery then check to make sure the charging system

Posted on May 11, 2009

  • 48 Answers

SOURCE: PROCEDURE FOR CHANGING ELECTRIC STARTER FOR KLX250 1999

dissconnect the battery locate the starter there should be two bolts holding it on remove them and disconnect the wire and install your new starter

Posted on Jan 14, 2009

heimlich
  • 1978 Answers

SOURCE: I have a 2001 Vulcan Nomad 1500 my problem and

I assume the engine is not seized and the battery is charged and good. Unplug the two small wires going to the starter solenoid and push the starter button . With a voltage meter on the wires from the harness you should have continuity.Reconnect the wires. Push the starter button, if you hear a click from the solenoid, the button is good. Now , jump the two cable posts on the starter solenoid. If the starter works you have a bad solenoid. If you push the starter button and tap on the starter with a plastic hammer and the starter works, you need new starter brushes. If anything else in the starter is keeping it from working you need a new starter , the starter parts are probably not available from the manufacturer.

Posted on Oct 03, 2010

19ken55
  • 426 Answers

SOURCE: 07 Kawasaki Vulcan 900 on start up the solenoid

Bad switch,Bad relay,bad solenoid the solenoid may need cleaning.
For troubleshooting remove the positive wire from the starter.
That is the biggest one. on the starter.
Now place a load on the wire say a headlight or 12 volt fan

Posted on Mar 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Derbi cross city 125. starter will not engage on the starter button but will engage by bridging the terminals on starter relay or by pressing the starter button when the engine is running.


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a "load" test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Security alarm needs a reset.
10. Starter control circuit, relay, or solenoid faulty.
11. Main fuse or circuit breaker may be blown or faulty.
12. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Derbi Cross City won start
1999 derbi Scooter won start need help Provoscooter com Forums
Derbi GPR50 starting problems
Derbi GP1 125 250 Workshop Manual

Aug 02, 2016 | Derbi Motorcycles

1 Answer

Hi folk ! My problem is. I put a new starter motor on my kazuma meerkat 50, I think it was made in 2003. So when I press the little button to make it start it just make a clicking sound but it not really...


Normally, that clicking sound coming from your starter, because your battery don't have the charge to turn the starter over. The clicking sound your hearing happens every time you start it, just usually goes unnoticed because the starter itself is louder. The clicking sound is the solenoid engaging, which is a good thing. But otherwise if you have already tried jumping it(I mean jump it your battery could be bad) you may just have a loss wire, bad starter, or a bad battery. I have got Brand New Starters that where bad, it don't happen often but it does happen.

But odds are, your battery is dead or bad

Good luck! Hope this helps!!!

Jun 06, 2014 | Motorcycles

1 Answer

Suzuki ozark 250


It sounds like the bendix, or engagement clutch is not fully engaging.
Unfortunatly this is a starter removal issue - you have to take the starter off to verify it.
The starter motor is turning (if it wasn't it wouldn't grind) so your batt and electric are good to that point.

Check the dealer to see if there are any similar problems for others and check "Bike Bandit" to see if they have the parts diagram - It is always easier, if you can see how the parts go together.
Good Luck

Nov 26, 2013 | Motorcycles

1 Answer

Doesn't start ...just stopped running.the start button won't turn it over but still drawing power(dims neutral light).i tried turning it over by shorting across the solenoid quad turns over but won't...


is it carbureted? if so try a deep cleaning,now on the start button issue it sounds like you need a new starter soleniod are there is a short somewhere. find a wiring digram and start trouble shooting at the solenoid.

Sep 17, 2013 | Arctic Cat 2006 250 DVX

1 Answer

Hi, bought my son a kazuma meerkat quad 50cc 2010 model electric start, unable to start the quad with the electric start? when ignition on & start button pressed selonoid clicks once & a sometimes...


I had the same problem. My positive wire would arc with the key off when connecting the battery showing a short somewhere. I disconnected the regulator/ rectifier, (where the #16 positive lead from the battery goes to), and it quit. I found a new one on e-bay for $9.90 after shipping and it corrected the problem. Check to make sure your positive is not arcing with the key off. Hope this helps.

Dec 15, 2010 | Quad 47 cc / 49 cc Pocket Mini Bike...

3 Answers

Suzuki 250cc quad bike wont start, just clicks when you press the start button anyone got any ideas


Three causes:

1: Dirty battery terminals

2: Battery is flat or dying

3: The starter motor is dead and all that is happening is the solenoid is clicking in and out

Feb 05, 2010 | Quad 47 cc / 49 cc Pocket Mini Bike...

1 Answer

Fault with electric start on my Suzuki GSF 250 Bandit


Check that the clutch is in, kick stand up, and neutral light ablaze. Then try your start button. When you had it running and hit the button, the starter engaged at a slower speed then the bike engine was turning, which led to the stall. The stall means your starter works. If the starter works when the engine is running then it is wiring. Check your kick stand wiring along with the clutch wires which plug in on the handlle bar or where the clutch cable enters the engine.

Oct 18, 2009 | 1995 Suzuki GSF 250 Bandit

5 Answers

My Quad bike won't start!


my quad runs fine on the kick start but when i do the elec start it truns over but wont start can u help me my quad is a corba 100cc auto 2004 mobel

Mar 30, 2009 | 2002 Honda CR 250 R

Not finding what you are looking for?
2002 kawasaki KLX 250 Logo

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...