Question about Suzuki VS 800 Intruder Motorcycles

2 Answers

I have a 92 suzuki vs800 with the wiring horness hanging off the front forks outside of the frame and im not sure to how it goes back into the frame?

Posted by on

  • imwillyhung Jun 15, 2009

    im sorry but i need to know how the horness is routed does it go under or over the frame and to the left or right of the fork.



2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 95 Answers

Remove your front,and place the horn inside of the space which has a ventilate and use the clamp to hold it,and screw it.

the horns are routed over the frames and the right/left of the fork.

Posted on Jun 17, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,341 Answers

You need to be careful due to the age of the bike as the wires may have become harder but brittle and any squeezing would mean any wire inside might snap..Also because it is coming at the front side of the bike it could be anything like a signal control,a horn wiring or even a thermostat switch wire..causing any loose connection might be very costly if you don't have the expertise..I have 15 years with re-conditioning old bikes that's why I think I can advise you.Now if you really want to hide the wires you will need to look for all the screws and bolts that covers the front and once out,all the wires are seen then you can hide them nicely back with a strap or a tape to prevent it coming back out when you are putting back the covers.Hope this helps.

Posted on Jun 15, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Wiring diagram starter solenoid 2004 suzuki intruder vs800

Hi, Wayne for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Suzuki, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2004 suzuki intruder vs800 wiring diagram Google Search
Suzuki Motorcycle Wiring Diagrams
Suzuki VS700 Service Manual
OEM parts for Suzuki

Btw, I’m available to help over the phone in case u need at

Mar 05, 2017 | 2003 Suzuki VS 800 Intruder

1 Answer

What is the fork oil capacity of a sv650 2002

This is Suzuki standard for a Pointy, sure someone will be along soon to say if Curvy is the same or not. Start at the standard air gap then see how it feels from there.

Front fork oil capacity (each leg) :
490 ml (16.56/17.25 US/Imp oz) for SV650
488 ml (16 .49/17.18 US/Imp oz) for SV650S

Fork oil level :
92 mm (3 .62 in) for SV650
94 mm (3.70 in) for SV650S

Jun 21, 2014 | 2002 Suzuki SV 650

1 Answer

Chasis nomber

what country?
each country is different, a what year, and what model suzuki.
ah, F2 is a motor cycle , you posted to Cars and trucks.
on a MC, the chassis, is on the front fork frame head, most bikes
and is covered in the F2 factory service manual.
its on the frame somewhere, for sure.

Feb 08, 2014 | Suzuki Cars & Trucks

1 Answer

1992 suzuki vs800 intruder need what weight fork oil and how much oil in forks

The recommended weight is Suzuki SAE 10W fork oil. The amount for the forks is 386ml or 13.5 ounces per side.

I’m happy to help further over the phone at

Feb 19, 2011 | 1992 Suzuki VS 800 Intruder

2 Answers

I have a 2000 Suzuki 1500 LC, I've got a wobble in the front end when I'm going about 30 -40 mph. I've been told that it's fork oil but not sure it has oil in it as it's got springs. Any idea what it...

A wobble that appears when slowing down is many times just low tire pressure. Check the front tire pressure should be 32-35 pds. Another thing that can cause a wobble is worn or loosely adjusted fork frame neck bearings(steering stem bearings). Disassemble around the handlebars down to the frame neck till you get the upper triple clamp off or can reach the adjuster nut , just underneath on top of the frame neck enough to tighten the steering stem bearings. You will need a shock adjusting tool (curved end with a single tooth) Comes standard in all Honda tool kits). Next, put a jack under the motor to lift the front wheel . Carefully wiggle the front wheel to see if you have a bad wheel bearing. If you do not have fork oil in your forks, you could possibly damage the chrome tubes. No oil would mean the forks would not go up and down smoothly. Do not add oil to your forks. Do not over fill your forks with oil. If you are not sure how much oil is in them, drain them and refill them with the correct amount. If you over fill the forks and drive the bike you will destroy the fork tubes.

Sep 24, 2010 | 2000 Suzuki VL 1500 Intruder LC

1 Answer

Cam timing 97 suzuki vs800

both cams are timmed of the rear piston at top dead center(make sure valves have a little freeplay, should move alittle, not tight)(timming mark shows r/f t in window)(window front of alternator cover) with the lines even with the head, arrows pointing forward.manual has a good detail if u have one. cam lobs should be down on back and about 10 o'clock on front.

May 26, 2010 | 1997 Suzuki VS 800 Intruder

1 Answer

How do I test for a bad solenoid on a 1994 Suzuki Intruder vs800

I'm assuming when you press the start button will not turn over. Look for the solonoid ( Relay) and you will see two heavy guage wire one goes to starter and the other to the battery terminal positive. Where the two wires meet at the relay jump with a heavy wire 10 guage it will by pass the relay if it starts your relay is bad.

Make sure your battey is hot bike in nuetral and clutch lever squeezed

Mar 08, 2010 | 1994 Suzuki VS 800 Intruder

1 Answer

My 2000 suzuki rm 125 does not shift into 4 and 5

The bike has a bent shift fork (or two). The engine needs to come out of the frame then gets torn down in order to replace the forks. Sorry.

Nov 14, 2009 | 2003 Suzuki RM 125

1 Answer

How does the vs800 sissy bar come off?

May I suggest a trip to your local library. Cycle repair books should be in 646 stacks of reference.

Oct 02, 2009 | Suzuki VS 800 Intruder Motorcycles

1 Answer


it (assuming it is a VS800) is in a trap door under the bike between the frame. disconnect the negative lug (left side) then the positive (right side) (this will be a small slotted screw viewable through a postage stamp sized window on the side of the battery cover) from underneath you remove the two front trap-door bolts and the cover will swing downward (be ready to support it as it swings) to add clearance have the back wheel up on a small thin board and one of equal size under the side stand for more info on suzuki intruders and boulevard series bikes check with

Nov 10, 2008 | 2003 Suzuki VS 800 Intruder

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

81400 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5057 Answers


Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides