Question about 2005 Harley Davidson FLHRS - FLHRSI Road King Custom

1 Answer

Seatrest drivers mounting drivers seat rest

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Harley Davidson Master
  • 40,868 Answers

Hi Anonymous, I would take a ride over to your local dealers parts department and have them print you out a copy of installation instructions. Good luck

Posted on May 01, 2015

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My seat belt is stuck behind head rest and will not release long enough to go back to proper setting

belt will not release if under tension , remove it at its mounting remove from head rest if it works now refit mounting,if not replace belt.

May 12, 2014 | Cars & Trucks

1 Answer

I have a 2008 Kawasaki Vulcan Nomad 1600 with 35,000 Kms or 21,800 miles. It is stored im my heated garage for the winter. I usually start it up once or twice a week. I tried to put it into gear and it...


    • 1

      Unscrew the passenger seat\'s mounting bolt, positioned on
      the rear of the seat, using a socket wrench and a 10 mm socket. Lift the
      passenger seat up and away from the rider\'s seat.

    • 2

      Flip the passenger seat upside down and place it on a clean
      work area. Pry out the seat cover\'s staples from the bottom of the seat
      pan with a small pry bar or staple puller. Pull off the vinyl cover and
      remove the foam from the seat pan.

    • 3

      Flip the seat pan over. Place the Utopia back rest bar over
      the top of the seat pan, following the contours of seat pan. Center the
      bar in the middle of the pan, then mark the location of the bar\'s
      mounting holes on the seat pan with a permanent marker. Remove the back
      rest bar.

    • 4

      Drill two holes into the seat pan at the marked locations,
      using an electric drill and a 9/32-inch drill bit. Place the back rest
      bar onto the seat pan. Screw the kit\'s bolts and lock washers through
      the bottom of the pan and into the back rest bar. Tighten the bolts with
      a 10 mm socket and a socket wrench.

    • 5

      Lay the seat\'s foam next to the seat pan. Mark the
      approximate location of the back rest bar\'s protruding neck at the front
      of the seat onto the foam with a permanent marker. Cut a slit into the
      foam at the marked area, using a sharp knife. Place the foam over the
      seat pan and push the bar\'s neck through the foam\'s newly cut slit.

    • 6

      Place the vinyl cover over the seat foam and pan. Pull the
      cover tight around the sides of the seat and staple it into place, using
      a heavy-duty staple gun. Cut a slit into the seat cover with a razor to
      allow the back rest bar\'s neck to extend outward. Remove the paper
      backing from the plastic boot included with the back rest kit. Slide the
      boot over the bar\'s neck and hold it firmly in place for 30 seconds.

    • 7

      Reinstall the passenger seat on the motorcycle and tighten
      its bolt with a 10 mm socket. Place the back rest over the bar\'s neck on
      the passenger seat. Slip a bolt through the backrest\'s mounting holes
      and into the tube on the bar\'s neck. Loosely screw a nut onto the end of
      the bolt. Adjust the angle of the back rest, then tighten the bolt and
      nut using a 10 mm socket and a 10 mm wrench.

Jan 17, 2013 | 2008 kawasaki Vulcan 1600 Nomad

1 Answer

Repair 300e driver seat armrest

Most often this is due to a loose armrest mounting bolt or worn limit washer, unzip the cover and tighten the arm rest first, it is most likely a T45 Torx female bolt head AKA star drive.

Aug 28, 2012 | 1992 Mercedes-Benz Mercedes Benz 300 Class

1 Answer

How do iremove front seat from a 1997 honda accord

1. Make sure you have the anti-theft codes for the radio and the navigation system, then write
down the frequencies for the preset buttons.
2. Tilt the steering wheel all the way up and telescope it all the way in.
3. '04-07 models passenger's seat: Carefully insert the tip of a small screwdriver (A) through
the hole in the back of the front seat belt lower anchor cover (B) and into the hole in the
front seat belt lower anchor (C). Unlock the lower anchor by pushing in on the screwdriver.
Remove the screwdriver, and then detach the front seat belt anchor plate (D) and anchor
cover from the lower anchor.4. Slide the seat all the way forward, then remove the seat track end covers from the back of both seat tracks.5. Slide the seat about half way to the rear so you can access the seat mounting bolts. If equipped with the driver's 8-way power seat, fully raise the seat.
6. If equipped with a side airbag, disconnect the negative cable from the battery, and wait at
least 3 minutes before removing the seat. 7. Remove the bolts securing the front seat. 8. Lift up the front seat, then detach the harness clip and disconnect the connector.
If equipped, the seat heater connector on the 2-way power seat and passenger's
manual seat. '04-07 models, disconnect the seat position sensor subharness connector on the
driver's manual height adjustable seat and the driver's 8-way power seat.
9. With the help of an assistant, carefully remove the front seat through the front door opening. 10. Install the seat in the reverse order of removal, and note these items:
Apply medium strength type liquid thread lock to the front seat mounting bolts
before reinstallation.
Make sure each connector is plugged in properly.
Tighten the seat mounting bolts to the specified torque in the sequence shown.
Slide the seat all the way back and tighten then slide it forward and
tighten Before attaching the lower anchor bolts, make sure there are no twists or kinks in
the seat belts. 04-07 models passenger's seat: The triangle marks on the anchor plate and
the lower anchor must face the same side. Insert the anchor plate into the lower
anchor, and make sure that it is locked securely. If equipped with a side airbag, reconnect the negative cable to the battery. Enter the anti-theft codes for the radio and navigation system, then enter the radio station presets. Reset the clock. Your all done. Drink a cold beverage and enjoy the rest of your weekend! hope this helps. Dave

Jun 16, 2011 | 1997 Honda Accord

1 Answer

Does anyone know of a drivers backrest for the dx

I doubt seriously if you're going to find a drivers back rest for your V-rod. The reason is the back rest is cnsidered to be a "touring" accessory and the V-rod is not generally considered to be a touring motorcycle.

I'd do a search online for "motorcycle seats" and see what comes up. Try Mustang Motorcycle Seats. They have good quality seats and reasonable prices. They also have the drivers backrest for a lot of their seats. If they offer a seat for the V-rod, maybe drop them an e-mail and ask about it.

Good Luck

Dec 22, 2010 | 2008 Harley Davidson VRSCDX Night Rod...

1 Answer

Install help driver seat back

remove seat the back rest mount will bolt to fender w rear passinger grabrail mounts 1/2 in nuts 2 of them,, mount there..

Aug 29, 2010 | 2002 Harley Davidson FLHT Electra Glide...

1 Answer

We need to remove the drives side head rest to install a seat cover, but we cannot figure out how to remove the head rest. How do you remove the driver's side head rest?

Head Restraints Removal
  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .


Aug 21, 2010 | 1998 Ford Taurus

1 Answer

How to remove the head rest from the driver's seat 05 sunfire

There should be tiny holes in the plastic covers at the base of the chrome rods attached to the headrest use a paper clip and push it in the holes as you pull on the headrest in the full up postion.

Dec 23, 2009 | Pontiac Sunfire Cars & Trucks

2 Answers

On a 1989 nissan maxima with sonar suspension II how do you disassemble the strut assembly? the mounting bracket for sonar adapters is in the way of the strut center bolt.

First you must remove the rear seat to gain access to the top strut mounts. The bottom of the rear seat comes out first. On the 91 model there are two tabs at the base of the seat bottm that you pull forward to release the seat bottom. I'm not sure if the 89 is the same. After removal of the rear seat bottom, you will see a bolt at the bottom of each side of the rear seat back that need to be removed. Fold down the arm rest and disconnect the vinyl cover at the base of the armrest to expose and remove two screws. Push up on the rear seat back to unhook three plastic hooks (center and one at each end) at the top of the rear seat back. Remove the seat back. Remove the large metal support panel that is behind the seat back. Safely jack up the rear of the car and support on jack stands so the rear wheels hang free. Doing one strut at a time, remove the two top strut mount bolts leaving the center strut stud nut in place. The strut and mount will lower out of the unibody. Disconnect the bottom strut mount. Remove the strut/coil spring assembly. Using a strut/spring compressor (some auto parts stores rent these) compress the spring. Carefully remove the top strut stud retaining nut, top strut mount, bumpers and strut boot. Carefully install compressed spring, strut boot, bumpers and top strut mount on new strut and install washer and retaining nut. Reinstall strut and etc. in reverse order.

Sep 15, 2009 | 1989 Nissan Maxima

1 Answer

Head rest 1984 240 4dr

push just below the head rest rails on the upolstry or just cut it open 3 inchs below each mount and push plastic tab

Jul 08, 2008 | 1984 Volvo 240 Series

Not finding what you are looking for?
2005 Harley Davidson FLHRS - FLHRSI Road King Custom Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers


Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides