Question about 2011 kawasaki KLX 110

1 Answer

2011 KLX110L electric start wont work

When push the electric start button, nothing happens. No lights and no engine start; there are no sounds at all...no clicks, ticks or vibrations. When kick start, the light will come on on the electric start, but it is still unresponsive. Is it starter? Starter sensor? Relay? Solenoid? Or am I not even close because of electric start light activity after kick start?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Have you tried sqeezing in the clutch lever while hiting the start button?

Rob

Posted on Mar 27, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
DickCanFixIt
  • 948 Answers

SOURCE: 2001 kaw Vulcan 1500 will not start. new battery, starter relay

Check continuity at the kill switch? sidestand switch? Either could be malfunctioning. What does your manual tell you about the starter relay circuit?

Posted on Jul 20, 2009

  • 5 Answers

SOURCE: Starting fault

There is also a safety switch on the clutch lever that could give the same symptoms.
Another thing to check is the fuse block that has a starter relay built in (hidden) above the fuse compartment. My D5 has the same symptoms and this is the problem. If I keep the starter button depressed for some seconds the relay operates and bike starts.

Posted on Mar 19, 2010

ftw1952
  • 10319 Answers

SOURCE: 2007 KLX250 KAW. Out

the starter hase a loose field inside the starters casing. That will cause the armature to rub and short out the entire electrical system when hitting the starter button. At times it will not in your case therefore the bearing or armature shaft is bent or very worn causing this to happen at times.

Posted on Dec 18, 2010

  • 8404 Answers

SOURCE: help my baby wont start. just getting a clicking

If everything is on and all voltages are proper at the proper time, all that is left is the starter motor. If it is as you say, the engine must be removed to do it, you may want to talk to the service manager at your Kawasaky shop. This is not a job for the faint of heart, and it does require special skills, tools and knowledge.

Posted on Oct 14, 2011

otisharr
  • 8 Answers

SOURCE: 1984 XLS Roadster Iron Head. Why doesn't it start?

HI YOU MITE TRY PUTING A METER OR A TEST LIGHT ON THE STARTER SOLENOID TREMINAL SMALL WIRE AND HIT THE START BUTTON TO SEE IF THE LIGHT COME ON ,IF NOT THE WIRE IS OPEN .IF LIGHT COME ON THEN THE STERTER NEED REPAIR OR REPLACE.

Posted on Feb 05, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool wed9400su0


Possible thermal fuse on blower housing, that's usually the problem if the timer is still ticking, it can be tested for contiuinty with a meter

Jan 23, 2014 | Whirlpool Dryers

1 Answer

2003 dodge ram has light tick for a minute at cold start then goes away


The 'light tick' is most probably a valve lifter. The valve lifters in the engine are hydraulic, and are pressurized by the engine's oil pump.
When the engine gets some mileage, say 60 or 70 thousand miles or more, the engine is just not as tight as it once was. What happens is that the lifter loses its pressure when the engine is not running, because there is some wear. When you start the engine, the lifter takes a few moments to pressurize, and makers a ticking noise until it does. The 'ticking' is the sound of the valve being hit by the push rod, which is being pushed by the lifter. Once the lifter is pressurized, the 'ticking' sound stops. This is a very common thing for engines, it will eventually happen to nearly every one.
Sometimes, thin, old oil can cause this. If you have not changed the oil/filter in a while, you should do it now.

This is nothing to really worry about right now, but it is a sign of engine wear. Just be sure to run the proper oil in the engine, and do all the proper maintenance.

Jun 19, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

Have a Whirlpool GEQ9800LW0 and it won't start. When I set the timer and push the start button nothing happens. The timer still makes it's usual clicking sound but the dryer won't start. What needs...


Check power to the inlet valve, if absent let the program move forward and if the motor does not work either it is possible that thetimer though ticking is not contacting.
So go back to check for the wash cycle, when start is pushed, inlet valve on, water comes in, water fills , triggers level sensors,washing starts with motor on.
If there is no voltage on any parts ,the timer contactor is faulty

Sep 19, 2010 | Whirlpool GEW9200L Electric Dryer

1 Answer

I have a Maytag PYE2300AYW. Push button but nothing happens. Had breakers to house checked and all good.


Dryer suddenly stop working when pushing start button (knob will make a humming or ticking kind of noise but won't turn on. I cleaned and check the outside exhaust and lint screen passage. Nothing is helping. help

Jan 08, 2010 | Maytag PYE2300AY Electric Dryer

1 Answer

Vibrations, tranny slipping, and engine tick


Sounds like you may have a worn out CV joint and the clicking may stop with an oil change. Good Luck

Jun 21, 2009 | 2003 BMW 325

1 Answer

Dryer will not start.. Here clicking sound when i push start button but nothing happens


Did you clean the lint screen and replace? Also - all lint should be cleaned from back of dryer and the duct...many dryer manufacturer have safety sensors that will not light dryer due to there being too much lint, not enough air flow...(safety feature) ...

Oct 09, 2008 | Kenmore 62602 Electric Dryer

1 Answer

No start


e3 fault??? sounds like an open sensor, located right nest to the thermaal fuse.

May 08, 2008 | Whirlpool GEW9200L Electric Dryer

Not finding what you are looking for?
2011 kawasaki KLX 110 Logo

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...