Question about 2008 Sym Mio 50

1 Answer

How do I manually turn off check engine light? I bought a used 2008 Sym Mio 50cc and have changed the oil myself. Is there a way to reset that light?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Sym Expert
  • 545 Answers

With ignition key switched to on, apply both brakes twice within five seconds

Posted on Mar 13, 2017

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3567 Answers

SOURCE: what sort of oil does my sym orbit 50 scooter use?

The engine needs 10w40 motor oil. NEVER use synthetic oil or oil with special additives.

Posted on Aug 15, 2009

Warf135
  • 137 Answers

SOURCE: put new engine in carnt get a spark at plug sym

There may be several things causing this fault (your sure the plug is fine?)

The ignition systems on these bikes are pretty basic. The Stator plate provides power to the CDI unit, which builds up until the pulser tells it to send the power to the coil and produce the spark

1. is there voltage from the stator plate (under flywheel) - you can test with a basic multimeter.

2. is the pulser sending a pulse - also can be tested with basic multimeter

3. is the CDI blown? - swap out to test

4. Is the Coil blown? - can be tested with multimeter

it is also very possible that you may have got a couple of wires mixed up when you switched engines.

Posted on Sep 20, 2009

  • 34 Answers

SOURCE: repairing a sym euro jet x 50cc scooter all aspects

Hello
Is it a GY6 Motor?
Go to www.scootdawg.com this forum should have wat you need also www.scooterrebels.com as well
Best Reguards

Larry

Posted on Jan 11, 2010

czaa
  • 4536 Answers

SOURCE: hello i have a 50cc

it may be-inspec the lines and tank--carb may need cleanin also chec air filter--make sure batt is at 12v-any less gives weak spark and power

Posted on Sep 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to access battery on a sym city hopper 1999


Hi, Barrie for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Sym, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://scooterunderground.ca/knowledge/manuals/documents/Symply50_Service_manual.pdf
SYM City Hopper 50cc
SYM Owners Manual

Mar 03, 2017 | Sym Motorcycles

1 Answer

Hi got a sym jet 4 rode it parked it up and now no spark at all help please is this a comon thing 2014 plate to


Hi, Ben and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting, leaking, spark plug cable connections loose check for spark leakage in the dark.
6. Faulty ignition coil or electronic control module.
7. Faulty CKP, CMP, or BAS sensor.
8. Faulty ignition switch.
9. Tilt sensor needs a reset.
10. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
no spark at all on 50cc sym jet euro sport Scooter Doc Forum
My scooter has no spark how to fix gy6 chinese scooter 139qmb qmb139 50cc...
Sym Jet 50 Service Manual
SYM JET 50 Spares Parts Accessories
SYM Fiddle II 125 AW12W Service Manual
SYM JOYRIDE 125 User Manual

Jan 16, 2017 | Sym Motorcycles

2 Answers

How to refuel a sym jolie 50cc scooter, do you mix oil into the petrol tank, or do you fill the oil and fuel seperatley or does it mix it itself????


Pretty much all are normal petrol in the fuel tank and the oil is on another tank. The oil is mixed as it enters the inlet manifold.

Your manual is here. Section 2-3
ScooterCommunity

Nov 06, 2016 | Sym Motorcycles

2 Answers

Engine light on after oil change but mechanic can't find problem


could be the oil change timer that needs to be reset look at you manual and see how to reset it , here is a you tube vid on how to do it http://www.youtube.com/watch?v=QDKCAIeOHeA

Nov 25, 2013 | 2008 Cadillac Cts

1 Answer

Yahoo.comI need to reset the change oil indicator. I just changed the oil, and looked for an owners manual not there. Bought car used sooo.


Try this,with engine off turn key to on position then push gas pedal 3 times usally that resets it for most cars.

May 15, 2011 | 2008 Dodge Avenger

1 Answer

I acnnot find how to reset the oil change required indicator light on my 2008 Mercury Sable


The following procedure will reset your oil change light. Thank you for using Fixya!

2008-2010 Sable
  1. Turn the ignition to run (one position before starting engine).
  2. Press and release SETUP to display "OIL LIFE XXX% HOLD RESET = NEW".
  3. Press and hold RESET for 2 seconds and release to reset the oil life to 100%.
  4. Turn the ignition off and then start the engine to verify the indicator has been reset.

Mar 04, 2011 | 2008 Mercury Sable

1 Answer

2002 Grand Prix: I just had my oil changed in my Pontiac 2008 Grand...


To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds. and wait for the light to flash. Check your manual it maybe slightly different. Real easy fix.

May 16, 2010 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
2008 Sym Mio 50 Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sym Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Dave Matthews
Dave Matthews

Level 2 Expert

97 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Sym Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...