Question about 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

Clutch cable rubbed a hole in the rear brake line. ABS light still on after repair. How do I reset it?

Reset ABS light

Posted by on

  • Floyd McMurray
    Floyd McMurray Mar 24, 2014

    2008 Ultra is the correct Harley not 2000.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Harley Davidson Master
  • 1,554 Answers

The ABS light should stay on until you reach a speed of about 3 MPH or higher.

Did you check for error codes?

1- Turn Ignition switch to OFF & Run/Stop switch is to Run.

2- Push odometer reset button in & hold.

3- Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word "diag" should then appear.

4 - Push the odometer reset button once and you will see the selection menu "PSSPt" with the first P flashing.

5 - Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
P = ECM/ICM (Electronic Control Module [EFI] / Ignition Control Module [Carbureted)
S = TSM/TSSM (Turn Signal/ Turn Signal Security Module)
SP = speedometer
T = tachometer

6 - To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC's the code will be displayed or the word "none" will appear if there are no DTC's. Push the odometer reset button again to view additional codes if they exist.

7 - Record the codes.

8 - If DTC's are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC's again by repeating steps 1 to 9. If the code is current it will reappear.

9 - Press and release the odometer reset button to continue to the next module.

10 - Turn Ignition switch to OFF.

On models not equipped with a tachometer "No Rsp" will appear when the tachometer identifier is selected.

"No Rsp" will also appear if the run/off switch is in the off position when doing this procedure.

Also if the code set is a historic code (not a constant light) after 50 start and run cycles of at least 30 seconds each in duration, the light will extinguish itself as long as the error hasn't occurred again.
If it were a current code, the light would remain lit while running.

If you clear the error code (step #8), the light SHOULD reset.

Posted on Mar 24, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Chevy blazer, lost most of brake peddle and


No reset on 98"s bleed all the lines. Replace all the lines in my opinion...That's what I do. we are talking almost 15 years of rust and fatigue...

Sep 24, 2014 | 1998 Chevrolet Blazer

1 Answer

I broke a rear brake line and repaired it now my abs brake light is in


I would take it to a parts store have codes read and ask that they clear the codes if the light comes on again you may still have air in the system have it bled.

Sep 02, 2014 | 2001 Buick Century

1 Answer

2006 Ford F350 4wd dually. Had ABS light come on. Found rear brakes bad. Replaced roters, calipers, brakes, brake lines and all new seals in rear dif. Rebuilt front dif, new seals, new brakes, roters,...


It doesn't cost anything to ask a question at a ford dealership . I would call and just explain what's going on. That one has me stumped. Good luck !!

Oct 29, 2013 | 2006 Ford F 350 Super Duty

1 Answer

Changed rear brake line from the reservoir to the ABS unit (hole in line from rubbing against clutch cable) on '08 HD Electra Glide. Installed new line. Bled the unit, have brakes, but when hard braking...


ABS units are tricky things, unless you know what you are doing your best bet is to leave it to the professionals. Yes you'll have to take it to your bike shop to have them bleed it correctly now.

Oct 22, 2013 | 2003 Gas Gas Pampera 280

2 Answers

Changed rear pads. Brake indicator on dash is still blinking and chiming. How do you reset


Is it the "brake"repair light blinking & chiming?? Or is it the "ABS" brake light blinking/chiming. Brake light should be red, ABS amber

Sep 05, 2011 | 2001 Chevrolet Tahoe

2 Answers

1999 Ford Ranger with 4 wheel ABS. I replaced the brakes on all four wheels and the rear wheel cylinders. The rear brake lines were open individually for a very brief time, and bled conventionally. I would...


The brake pads and shoes are not elec., your abs light is on because your abs computer pick up a bad signal from one of your abs sensor's,, take it to any auto parts or some one like autozone where they can do a code reading and get back us with the code so we can help you diag. your trouble code.

Jun 14, 2010 | 1999 Ford Ranger SuperCab

2 Answers

Repaired brake line .need to reset light on dash


try taking off the positive battery cable for a few minutes and replace it. This should work to reset your computer which controls those lights.

Apr 13, 2010 | 1995 Saturn Sl

4 Answers

Abs light came on and a tc with line through it came on


when you have antilock "problem " on this vehicle you automatically get t\c light, I fixed this problem for a friend when the tire rubbed through one of his abs sensor cables .. just re-connected it don't spend $500 at a "RELIABLE" shop if you can fix this yourself....they will never tell you how easy it might be to repair!!

Feb 07, 2010 | 2003 Hummer H2

1 Answer

92 dodge van rear ABS-brake and ABS lights on/can't reset?


Its probably how your bleeding your brakes, but first make sure the bleeding nipples are facing upward. You should bleed diagonaly, front pass wheel then rear driver wheel. Then front driver wheel and rear pass wheel. The abs light has its own computer your have to get it scanned to clear the codes and turn off the light

Mar 18, 2009 | 1992 Oldsmobile Ninety Eight Regency

Not finding what you are looking for?
2000 Harley Davidson FLHR-FLHRI Road king Logo

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...