Question about 2002 Harley Davidson FLHR - FLHRCI Road king

1 Answer

Front indicator lights on ,speedo lit but no display,brake light not working,rear indicator lights not on,but flash when ignition is in on position what's the problem

Turn signals do not work either what is the possible cause

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

Bad connection , probably a block connector plug , disconnect the plug from the socket and spray terminals with wd 40 .

Posted on Mar 23, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 8404 Answers

SOURCE: My rear tail light does not work when the front

You should have two filaments in the reat taillight lamp, one for tail light and one for brake light. You are not confusing these filaments/functions are you?

What you seem to be saying to me is that you have a lamp that had no tail light filament (burned out) but does have a brake light filament still intact.

Remove the light and check it visually and/or with a contunity tester.

I hope this helps you ...

If I misunderstood your question, please ask me again

a

Posted on Oct 02, 2009

  • 1 Answer

SOURCE: right signal not flashing signals dont light up for night

2005 sportster custom will only run with choke on

Posted on Mar 20, 2010

  • 4 Answers

SOURCE: Battery checks good turn ignition

Check out near the ignition there should be two small rectangular circuit breakers rather than fuses one may be faulty best to carefully bridge the terminals of these with a fuse in a fuse holder of 10 amp with 10 Amp fuse fitted use the pigtails off the fuse holder to bridge the suspect circuit breaker if thats the problem the bike should start and all lights work if you have a short the fuse will blow also. If the problem is sorted with the fuse bridging proceed to replace the faulty circuit breaker keep the wiring original dont be tempted to patch it up use original replacement part

Posted on Sep 01, 2010

wd4ity
  • 4565 Answers

SOURCE: Only right turn signal works.

Ok, there is only a few things that could cause this. They include:

handlebar directional switch on inoperative side not functioning.
broken or disconnected wire in the directional switch circuit
a possible combination of causes found in problem #1.
module malfunction.

You need to test the left turn signal switch to make sure it has voltage going to it and when you press the switch, 12 volts is going to the turn signal cancelling unit. This 12 volt pulse from the switch is what tells the module to turn the left turn signals on. Without the pulse, the module doesn't know you've pressed the switch. You may need a wiring diagram to trace this out. Sorry but I don't have one for that year model.

Good Luck
Steve


Posted on Nov 16, 2010

  • 2926 Answers

SOURCE: Turn signals, horn and brake

Not sure of the year of your bike, but if you have an aftermarket alarm system, it is related to the alarm system itself or a bad relay in the circuit.

Posted on Nov 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake/Signal Lights Problem.


Sounds like a ground problem to me. Bulbs are not getting there ground to complete the circuit so they backfed through the other bulbs.

Oct 23, 2012 | 1998 Acura RL 3.5

Tip

Wiring Diagram Kawasaki GPZ 750


Kawasaki GPZ750 (ZX750) Turbo North American models.<br /><br /><img src="suzman_10.JPG" /><br /><br />1 - Right turn <br />2 - High beam<br />3 - Warning light<br />4 - Headlight fail<br />5 - Neutral<br />6 - Left turn<br />7 - Boost Guage <br />8 - Tach light<br />9 - Tach/volt switch<br />10 + 11 - Speedo lights<br />12 + 13 - Illum. lights<br />14 - Spare connectors<br />15 - LCD + warnig lights<br />15 + 16 - LCD illum<br />17 - RF indicator<br />18 - Horns<br />19 - Headlamp<br />21 - LF indicator<br />22 - Reserve lighting unit<br />23 - Hazard switch<br />24 - Indicator switch<br />25 - Horn switch<br />26 - Dimmer switch<br />27 - Starter lockout switch<br />28 - Neutral switch<br />29 - Side stand switch<br />31 - Oil pressure switch<br />32 - Alternator<br />33 - Regulator<br />34 - Solenoid<br />35 - Starter<br />36 - Battery<br />37 - Junction box<br />38 - LR Indicator<br />39 - Stop/tail lamps<br />40 - Stop/tail lamps<br />41 - RR Indicator<br />42 - Injectors<br />43 - Engine temp switch<br />44 - Boost sensor<br />45 - Fuel pump<br />46 - Air temp sensor<br />47 - Throttle sensor<br />48 - Main pump relay<br />49 - Fuel injection control unit<br />50 - Rear brake switch<br />51 - Pick-up coils<br />52 - Ignition control unit<br />53 - Coils<br />54 - Spark plugs<br />55 - Fuel level sensor<br />56 - Front brake switch<br />57 - Starter/engine stop<br />58 - Ignition<br />

on Nov 22, 2010 | Motorcycles

1 Answer

1998 dodge Dakota Ok so I just got this truck and when I got it the abs light and brake light were on plus the speedo doesn't work sometimes I replaced the rear speed sense on the diff but the lights...


If the red brake light and the ABS light are both lit up on the dashboard, do NOT drive the vehicle. It indicates a major malfuntion with the brake system. The red light indicates low brake fluid or the parking brake engaged. The yellow ABS without the red light, indicates a problem the computer found and it disables the ABS system while still having conventional brakes. Since both are lit, it needs the brake system repaired. What you replaced on the rear diff was probably the rear ABS sensor. The vehicle speed sensor for the speedometer should be located on the rear of your transfer case if you have 4WD, or on the rear of the trans if you have 2WD.

Oct 11, 2012 | Cars & Trucks

1 Answer

Rear hazard flashers don't work 1994 Chevrolet Cavalier


Hazard flasher power comes from the 20A S/LP fuse in the fuse block. It is applied to the hazard flasher in the convenience center. Flasher output is applied to the turn/hazard/headlight SWITCH assembly where activation of the HAZARD switch causes flashing power to be applied to the turn indicators and the turn filaments of the front and rear dual park/turn lights. If replacing the fuse doesn't work, trace the power through the circuit. Check for misssing/disconnected ground wires.

Sep 16, 2012 | Chevrolet Vehicle Parts & Accessories

1 Answer

Brake pad wear indicator light does not go off at the dash after changing rotors brake pads and the sensor in the front wheels all pads and rotors and the sensor is ok at rear. the vehicle has only 30000...


Did you change the sensor? if you did, do a battery reset (disconnect for 10 to 20 min.).

Obviously the wear sensor has made contact with the rotor and is already damaged. You're not even suppose to resuse the wear pad sensor if its worn or damaged anyways.The way how the sensor works is that it must make contact to the rotor to complete the wear pad light indicator circuit. There is no mentioning that he replaced the the wear pad sensor with a new one.

But if one did replaced the wear pad sensor and the wear pad indicator is lit up, the way to reset it is to leave the key on in ignition switch #2 or #1 for about 30sec. turn it off and its reset.

Its possible that you forgot to replace the brake light sensors. They are about 15 bucks, and have to be replaced in order for that light to turn off. You can either get them from the dealer where they'll likely charge you 3 times as much, or you can go to http://www.turnermotorsport.com and get them there.

You have to reset the light by leaving the ignition switch on position #2 for about 30 sec. turn off the ignition and start the engine up and see if it goes out. I recommend buying a new wear pad sensor as well because now light will lit up when you're way below spec (less than 3mm)

Also, you could try with this procedure for one E39: Turning off the Check Brake Linings warning on the Instrument Cluster...
- so you've just changed the brake pads on your E39, along with the wear sensors. The old sensor(s) needed replacement cause you waited a bit too long before changing the pads, and wore through the sensor(s), turning on the BRAKE light on the dash. But wait, the light is still on? But there's a new sensor installed... what gives?!
- there is a procedure required in order to turn off the light/warning. With the ignition off, step on and hold the brake pedal. Now, while holding the brake pedal down, turn on the ignition switch to position 2 (just before cranking). Hold the brake pedal until the BRAKE light is off. Tada, the warning is gone and reset.

NOTE: This procedure worked on a 2001 E46 325i. It took about 15-20 seconds, but it cleared out w/o having to unhook the battery.

Other details find in the Owners Manual 2006-BMW-Z4m-Roadster-Owner-Manual

Keep us updated.

Nov 04, 2010 | 2006 BMW Z4 Roadster

1 Answer

Yellow light burning


That is the brake pad wear indicator. Probably need to have your front brakes and the brake sensor replaced. Might be rear brakes, but they don't wear out as often.

Jul 12, 2010 | 2004 Mini Cooper

1 Answer

1989 Cadillac rear lights stay on


It may be a turn hazard module under dash.that is the culprit! The power to the third brake light does not go through the module, but the rear brake lamps power is controlled through this module. I am looking at a drawing of one and it looks like it has two connectors with about five wires in one and six in the other. It has some cooling fins on it also.

May 30, 2009 | 1989 Cadillac Brougham

1 Answer

Signal light system problem


You have a bad ground somewhere .. try the rear lights first make sure each light is grounded good .. then try front ones and see if they are grounded also. Remove bulbs and replace them and make sure each is in good clean condition.. thanks Jerry holler if you have more

Jan 30, 2009 | 1997 Volkswagen Jetta

3 Answers

Focus remote key fob not working


this info would cost you £30.+ at ford Radio Frequency Programming Instructions:
  • Insert the ignition key and turn from position II (Ignition) to position 0 (All off) and back four times within three seconds.
  • Remove the ignition key. The locking control system is now in "learn mode" for the next 20 seconds and the red warning system LED (By the clock) stays on continuously to indicate this.
  • During the 20 seconds press one of the transmitter buttons. The remotes signal and code number is learned by the locking module and is indicated by flashing the warning system LED.
  • Wait until learn mode times out (20 seconds) or switch the ignition back to ON.nfrared Programming Instructions:
  • Put your key into the ignition and turn to position 1 (Radio). After approximately 10 seconds the red alarm control LED (next to the clock) should illuminate. As soon as it comes on remove the key from the ignition - the LED should remain lit.
  • Point the remote's "eye" at one of the front door sensors and press the rear button until the light on the transmitter illuminates (Keep the button pressed)
  • With the rear button held in press the front button 4 times then release both at the same time. The control lights in both clock and fob will flash 4 times to indicate programming complete.
  • Turn the ignition back on to exit programming mode

Nov 28, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2002 Harley Davidson FLHR - FLHRCI Road king Logo

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Mike

Level 3 Expert

4339 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...