Question about 2006 Bajaj Wind 125

1 Answer

Cluth houseng gear and idle gear always brooken what is the couse

Why the cluth houseng gear and the idle gear

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Get rid of your bike. the problem is simply poor quality materials used for making these bikes.

Posted on Mar 21, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 dodge dakota sport with 2.5 engine idles high when I start it up, continues idling high, when pushing clutch in to change gears it idles extremely high


Does it do it if you disconnect the idle air control valve ?
You need to know if its a vac leak or if the computer is making the valve open too far.

Feb 09, 2014 | 2001 Dodge Dakota

1 Answer

Cluth trouble


Need clutch adjustment

Dec 16, 2013 | Garden

1 Answer

When i turn on computet, my cpu,mouse, keybord all hardwear run but my moniter don't show anything. my moniter is always run but in my cpu mistek


are your monitor okey.try with a other monitor if it work your monitor is brooken.if not you have a brooken videocard.
all cabels should allways be seated tight.

Jun 10, 2013 | Computers & Internet

1 Answer

I have a 1988 chevy silverado 2500 5.7 wat wiill couse the motor to die wile in reverse and sumtimes when im at a stop light in gear idleing it will die to it has all new plugs wires n sensors


u probly didnt need new sensors-did u havit scanned 1st------a dirty throttle body and idle contrl motor is common------use a nonchlorinated solution

Oct 21, 2011 | 1988 Chevrolet Silverado 2500

1 Answer

My clutch slipps whit i hit 3000rpms in all gears .. do i need a new clutch


Ive always checked the cluth by putting it in like 3rd gear and giving it a little gas before you release clucth pedal should almost want to stall but if it whinds up then you probably need clutch.

Feb 04, 2010 | 1995 Volkswagen Jetta

1 Answer

Hello I have just had a new clutch fitted into my Hyundai Accent Coupe (2000) and yet the thrust bearing is still noisy and it is notchy going into 2/3 gears and when dropping down from 5th to 4th - any...


if you used the car with a bad cluth you may have damaged the syncromesh, it nearly always happens in 3rd gear. Sounds like the fault, the syncromesh is part of the gearbox and most often cannot be fixed without a new gearbox.

Jan 13, 2010 | 2000 Hyundai Accent

1 Answer

After traveling about 8km my car wont go into 1st or reverse gear. when it is cold it goes into all the gears fine. when i switch the car off it will go into gear. we did put a new(aftermarket clutch) in a...


Cluth cable ajustment if equiped.Some cars have a cluth cylender if your model has the cylender no ajustment is available.If you had your cluth changed at a garage you might consider takeing it back in for ajustments.If you changed the clutch check cluth cable for ajustment if your car is equiped with cable if not i would perhaps remove the transmission and inspect clutch for loose clutch plate or release bearing might not be seated properly hope this helped you.

Dec 24, 2009 | Mazda 323 Cars & Trucks

2 Answers

I can not pot my ford focus in gear i dont now what is is as cant finf cluth cable and the cluth peddel got no preass be hind it and my car is 2001 and do u now where the cluth is in the engean


yes the clutch is
well u have to take the gear box out
and the clutch is on the back of the engine


now the cable runs from the pedel to the gear box
if u look u will see a blck cable and you can adjust it
it might need adjusting

Aug 02, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2006 Bajaj Wind 125 Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bajaj Experts

sachin sharma
sachin sharma

Level 2 Expert

171 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Joseph Gallucci

Level 2 Expert

120 Answers

Are you a Bajaj Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...