Question about 2005 Honda XR 100 Motard

1 Answer

Kick start My 1986 honda xr100r dirtbike Has no compression, the kick start locks up then you kick it over haarder than usual and it releases then it locks up again within 1 minute

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Honda Expert
  • 391 Answers

Run a compression check. If it's low, solve that problem first.

Posted on May 15, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
wilsodfarm
  • 986 Answers

SOURCE: It's a 1986 xr 250.

Im not being a smart ==== but do you have fire and fuel sounds like its in time or you would not have compression

Posted on Feb 11, 2010

Thermo King
  • 593 Answers

SOURCE: can't get my 2002 honda xr100r started. I can't

The engine electrics need to be turned on. You have to have power to the ign. coil to start.

Posted on Oct 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my 1991 honda xr100r smoking?


Hi, Anonymous your instrument gauges and lights can alert you to most electrical and engine issues they can not warn you about failed engine gaskets or seals so your engine has to resort to old fashion alert methods of colored "SMOKE SIGNALS" here is a breakdown of their meaning:
1. COLORLESS OR SLIGHTLY BLUE SMOKE on start-up means your air/fuel mixture is at the right composition and everything is well burnt in your combustion chamber.
2. BLUE SMOKE on startup is usually caused by failed valve seals dripping oil into the combustion chamber when the engine is not running.
3. YELLOW OR BROWNISH SMOKE at start-up means your air/fuel mixture is too lean. Too lean means that there is low fuel but high air mixture in your combustion chamber.
4. WHITE SMOKE on startup may be caused by a blown head gasket allowing coolant to enter the combustion chamber and may start dripping out of the exhaust pipes or mufflers. Smoke while riding is usually caused by worn out or damaged valves, seals, guides, pistons, rings, or cylinder walls.
5. BLACK SMOKE on startup is usually caused by too much fuel in the combustion chamber this can be due to air/fuel mixture adjustment too rich, accelerator pump improperly adjusted, faulty choke/enrichner or not in the off position, air filter dirty and clogged, faulty carburetor float needle and seat, pilot jet too large, fuel injectors leaking, smoke while riding is usually caused by the main jet being too large or a damaged carburetor.
It should be noted that aggressive or abnormal throttle operation will cause these conditions to manifest themselves exponentially.
For more information about your issue and valuable "FREE" downloads that you will need for viewing and printing please click on the links below. Good luck and have a nice day.
xr100 smokes
Why is my xr100 smoking
XR80R XR100R service manual repair 1985 1997 XR80 XR100 Download Manuals... $10
http://www.partsfish.com/page/oem-parts-for-honda
Honda XR100R 1996 Owner Manual

May 29, 2014 | Honda Motorcycles

1 Answer

Dirtbike kick star


this happened with my sons pw50 where the piston ring had snapped and when it locked it was stuck bewteen the piston & bore

i would seek a shop or mechaninc to look at the top end and isnpect the piston & rings for wear or damage

dont keep kicking as this could result in further damage

Mar 20, 2014 | 2003 Yamaha YZ 125

1 Answer

1994 Honda XR80R does not go into gear


Hi, Anonymous and the usual suspects are:
1. Clutch not disengaging.
2. Bent shift shaft.
3. Shift fork bent or seized.
4. Gear seized on the shaft.
5. Gear positioning lever binding.
6. Shift return springs weak or broken.
7. Shift return spring pin loose
8. Shift mechanism arm spring is broken.
9. Shift mechanism arm is broken.
10. Shift drum is broken.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2002 XR80 Will Not Shift Into Gear Texas Offroad Network Forums
Shifting Problems Honda Dirtbike XL100 XR100 ETC
XR80R XR100R service manual repair 1985 1997 XR80 XR100 Download Manuals...
http://www.partsfish.com/page/oem-parts-for-honda
http://mybikemanuals.com/honda/honda-xr-owners-manuals

Feb 02, 2014 | Honda Motorcycles

1 Answer

2002 Honda CR 250 R lost all compression


Hi, Brandy for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2001 CR250 Fresh top end no compression
2001 CR250 Fresh top end no compression
CR250 2002 2003 pdf
http://www.partsfish.com/page/oem-parts-for-honda
http://owners.honda.com/assets/ownerlink/model/own_man/powersports/2007/2007_cr250r.pdf

Mar 04, 2012 | 2002 Honda CR 250 R

1 Answer

125cc won't kick over


MAKE SURE YOU HAVE SPARK AT THE PLUG
MAKE SURE YOU HAVE COMPRESSION
REMOVE PLUG PUT FINGER OVER HOLE AND KICK
IF YOU HAVE BOTH OF THOSE TRY CLEANING THE JETS IN THE CARB

Jan 15, 2010 | 2003 Yamaha YZ 125

2 Answers

When trying to start bike there is a big backfire


There is a proper way to start the engine. Four controls are on your bike to assist in starting. Below are generic instructions.
  • The choke, used when the engine is cold. Pull the red knob for choke.
  • The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
  • The de-compression lever, always used.
  • The throttle, used to prime the cylinder, (power valve).
Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Now release the de-compression lever. Give the throttle a 1/4 turn then let it snap closed. A diaphragm, (Power valve), in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. A flooded engine will often backfire. Now give a strong kick through the full sweep of the kick start lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from the kick lever. This happens in the case of a misfire, aka > backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), for six kicks. After six kicks go ahead and twist the throttle again for a second priming. A good battery, a clean spark plug, a clean carb and clean air filter will also aid in starting. Note that not all carbs have a power valve. When a power valve is not present you should crack the throttle open only 1/8 inch from closed on each kick.

Nov 17, 2009 | 1996 Honda Hornet 250

1 Answer

2007 honda crf 250 r hard starting when cold ,


There is a proper way to start an engine. Most bikes have four controls to assist in starting.
  • The choke, used when the engine is cold. Pull the red knob for choke.
  • The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
  • The de-compression lever, always used.
  • The throttle, used to prime the cylinder.
Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Now release the de-compression lever. Give the throttle a 1/4 turn then let it snap closed. A diaphragm in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. A flooded engine will often backfire. Now give a strong kick through the full sweep of the kick start lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from the kick lever. This happens in the case of a misfire, aka > backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), until the bike starts. Go ahead and give it another primer shot after the 5th kick attempt. A good battery, a clean spark plug, a clean carb and clean air filter will also aid in starting.

Sep 23, 2009 | 2005 Honda CRF 250 R

1 Answer

Bike is sometimes hard to start.When bike stalls and goes dead,it is hard to start again.This is a 2003 honda crf450.


There is a proper way to start the engine. Four controls are on your bike to assist in starting.
  • The choke, used when the engine is cold. Pull the red knob for choke.
  • The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
  • The de-compression lever, always used.
  • The throttle, used to prime the cylinder.
Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Now release the de-compression lever. Give the throttle a 1/4 turn then let it snap closed. A diaphragm in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. A flooded engine will often backfire. Now give a strong kick through the full sweep of the kick start lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from the kick lever. This happens in the case of a misfire, aka > backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), until the bike starts. A good battery, a clean spark plug, a clean carb and clean air filter will also aid in starting.

Jun 28, 2009 | 2003 Honda CRF 450 R

3 Answers

Its getting dam near impossible to kick start, it will start after 30 or so kicks, any ideas?


Could be low compression due to head gasket leak, worn piston rings. Or bad spark due to dirty plug, wrong gap, plug breaking down, lead or cap breaking down, ignition fault. Choked air filter, fuel filter.
Try these in easiest order I.E. remove air filter and see if it starts easier, do a compression test, cahnge plug, lead cap. Check the fuel filter.
I am sure it's a simple solution.(high milage engines tend to be difficult to start so take this into account)

Jun 27, 2009 | 2004 Honda CRF 450 R

Not finding what you are looking for?
2005 Honda XR 100 Motard Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Mike

Level 3 Expert

4339 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...