Question about 2011 kawasaki VN 900 Classic

1 Answer

Two hose in air box can i put them together

Removed air box what do i do w/ hoses

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • kawasaki Expert
  • 391 Answers

The short answer is no. Where do the hoses come from?

Posted on Apr 13, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change thermostat in malibu 2001


Follow the radiator hose back to the engine on the top side. Where the hose connects to the engine is the thermostat housing. Remove the hose clamp and hose (when vehicle is cool). remove the housing itself and the thermostat will be right in front of you. Replace an put it back together. Fill up the radiator fluid again. After you start the motor for about 2 minutes check the fluid again and top off if needed.

Feb 17, 2015 | 2001 Chevrolet Chevrolet Malibu LS

1 Answer

How to remove a power steering pump


I just did this for my Silverado. you need to remove the air tube going to the air box. that's to help get at the belt tensioner. remove the belt and the alternator. you will have to disconnect the battery before the alternator. once you get those off. there are 5 bolts hold the bracket in place. 4 long bolts in the front 1 way down at the bottom. and a short bolt hiding behind the hoses near the exhaust. once you get those loose. remove the hoses that have the clamps and slide those off and point them up to not lose all the oil out of them. have a pan under the truck to catch any oil dripping. then remove the bolts and pull the bracket with the power steering pump out. you will now have to unbolt the pressure hose and then you have to pull the pulley off. there is a special tool just for that. then there are 3 bolts to get the pump off. reverse to put it back together

Feb 11, 2015 | 2002 Chevrolet Suburban

1 Answer

Where is the thermostat mounted?


    • 1. Locate the thermostat housing by following the radiator hose from the radiator to the engine block. The metal cover that the hose attaches to is the Tahoe's thermostat housing.

    • 2

      Remove the radiator hose retention clip by manually squeezing the clip tabs together. With the tabs together, pull the hose off the thermostat housing. Drain the fluid from the hose by holding the hose in the air. The fluid will drain back into the radiator.

    • 3

      Remove the thermostat housing by taking off the two bolts with a boxed wrench. Lift the hosing off the engine to expose the thermostat.

    • 4

      Pull the old thermostat out of the Tahoe's intake manifold. Place the new one into the intake manifold with the spring-loaded end inside of the intake.

    • 5

      Replace the old thermostat gasket with a new one. The gasket must remain dry during the installation process.

    • 6

      Place the thermostat housing on top of the thermostat gasket and bolt it into place.

    • 7

      Squeeze the radiator hose retention clip tabs together and slide the hose back onto the thermostat housing. Let go of the tabs to secure the hose into place.

Sponsored Links

Read more: http://www.ehow.com/how_6395786_change-thermostat-2003-tahoe.html#ixzz30u7ZzxV6

Mar 23, 2014 | 2000 Chevrolet Tahoe

1 Answer

Bosch dishwasher SHU4000 problem starting, not draining


Drain problems are almost always going to be a clog. Disconnect the drain hose from the air gap vent at the sink top. Place a bucket under the hose and run the drain cycle. Unit should drain. If not, clog is either in drain hose or under the dishwasher's internal filter. Remove filter. Locate the item causing the clog and remove it. If nothing is found here, the problem will be in the air vent gap filter itself. Disconnect the other hose and remove the air vent gap from the sink. There's a small cap at the top of the filter. Press the clips in to remove the cap. Flush the unit with water or use a thin, long blade screwdriver to remove the debris.

Put it all back together and test again. You should be fine.

Mar 20, 2010 | Bosch SHU4006 Dishwasher

2 Answers

Where is thermostat on the 2000 Deville??


he thermostat housing is located on top of the motor, underneath the air intake assembly. The easiest way to remove it, is just take off the air cleaner assembly. Unscrew the plastic nut on top of the air cleaner (above the throttle body), and then remove the 4 screws that hold the top onto the air filter box. It will start to lift off now, but there's several hoses and vacuum lines attached. The rubber hoses should have plastic clips holding them in place, these can be CAREFULLY separated with a screw driver, and then just pull the hoses off. The vacuum lines are underneath it, CAREFULLY pull these off, or pry them off with a screw driver. Make sure you remember which ones go where! With this off, the housing is easy to see, the upper radiator hose on the driver side of the car goes right into it. Remove this hose, be prepared to spill some coolant. Have towels ready to catch/mop up what you spill, and have some extra coolant handy to replace what is lost when you're done. There should be a couple bolts holding the housing on, remove these. There might be a sensor in this as well, I don't remember, unplug it if it's in the way. Pull the housing cover off, and the thermostat should be right underneath. It just lifts out, make sure you put the new one in the same way the old one came out, in other words, don't put it in upside down, it won't work. Also, make sure you have a new gasket for the housing, you should never reuse the old one. If needed, clean of any old gasket material or sealant, try not to get any into the coolant. It's not required, but it never hurts to use some RTV sealant when you put the housing back on. Reinstall everything, add coolant if needed, and don't forget to recheck the coolant level after the engine heats up, it'll probably drop once the thermostat opens up.

Aug 10, 2009 | 2000 Cadillac DeVille

2 Answers

How do you change the air filters in the Royal Star Tour Deluxe?


if you don't see an air box prominent...remove your saddle and the airbox and filter is under the saddle...your bike manual should cover this

Jul 21, 2009 | 2008 Yamaha Royal Star Tour Deluxe

1 Answer

How to replace engine air filter


  1. Disconnect negative battery cable.
  2. Disconnect inlet air temperature sensor electrical connector.
  3. Disconnect fresh air makeup hose from throttle body air inlet hose.
  4. Disconnect PCV hose from intake manifold.
  5. Loosen hose clamp at throttle body air inlet hose. Remove hose from throttle body
  6. Push in on locking tabs to disengage air inlet hose from air cleaner housing. Remove throttle body air inlet hose and air cleaner element together.
  7. Separate air cleaner element from throttle body air inlet hose.
INSTALLATION reverse

Jun 11, 2009 | 2002 Chrysler Sebring

2 Answers

I need to change the heater core and can not find it how do i get to it


under the hood rh side ( passngr ) split the heater boxes r&r as required

hope2help shack

Apr 16, 2009 | 1999 Jeep Grand Cherokee

1 Answer

1997 bonneville ssei


Grab yourself a cable type hose clamp tool.. a long pair of hose removal pliers. drain the radiator and remove the hose clamps and hosed from the passenger side firewall ( hidden behind the A/c acumulator ).
from the passenger side remove the end cap from the heater box under the dash. take it out and put it back together in the reverse order.

Nov 02, 2008 | 1997 Pontiac Bonneville

2 Answers

AIR FILTER


There is an air box with 2 hoses one going to the intake and one underneath going to another airbox, loosen the clamps and pop off the hose to the lower airbox and remove the 2 10mm bolts holding the top one to the radiator support. There are 2 clips holding the lower box lid in place pop them open rotate the lid toward the rad and remove the old filter and replace it with the new one. The assembly is reversing the order to take it apart I had trouble with this the first time I did it also.

Jul 23, 2008 | 2000 Dodge Caravan

Not finding what you are looking for?
2011 kawasaki VN 900 Classic Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...