Question about 1994 Yamaha XV 535 Virago DX

1 Answer

Clutch cant select gears

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 54 Answers

Check the cable is tight enough or if hydraulic that the clutch piston is not sticking

Posted on Oct 21, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi guys I have a 2005 peugeot 206. I have recently installed a new clutch. Everything was installed corectly and tightened accordingly. Once i put the gear box back on and turned on the car i cant get any...


sounds like the trust bearing has not been installed this fits on the fork in the clutch house that engages the clutch to release so gears can be changed, if its not locked in place it will not catch the clutch and is probably sitting in the bottom of the clutch housing.

Jul 17, 2017 | Peugeot Cars & Trucks

1 Answer

Hi i drive a 03 ford transit when you press the clutch pedal it feels fine but you cant select gears only 5 gear when you try to get first gear its like the clutch is not being pressed


Your clutch disc may be worn out, when the disc wears completely down the pressure plate goes over center and that causes the clutch to slightly engage when the pedal is depressed and you grind gears, most clutches last about 75000 miles.

Oct 20, 2016 | Ford Cars & Trucks

1 Answer

Suzuki katana 600 clutch problem, can anyone help?


engine off ! try rocking back and forward and shift gears down to 1st then back till in neauteral ! if u select 1st and pull clutch in you should be able to push the bike , if not check adjustment !

Aug 14, 2014 | Suzuki GSX 600 F (Katana Motorcycles

1 Answer

Lost speed.5th gear stoped working


old car. 5th gear? is this M/T? 1987 ?
A/T? is 4speed

what does stopped working mean .
1: shifter fails to select 5 gear H pattern slot.
2: grinds?
3: cant force it to 5th with clutch depressed.? is free play at spec?
4: raise front wheels off ground, can you get in to 5th now? keyout and running?
5: can you get into 5th parked engine off, and select 5th and then start car in 5th with clutch depresses first step. then slowly very slowly attempt to move car starting in 5th, but dont finish, just feel the gear, feel that its there and not neutral.

not working ,says nothing at all.

Sep 13, 2013 | 1987 Honda Prelude

1 Answer

Clutch cable geo tracker


don't want to shift? fills a huge basket ,
1: grinds?
2: can't get in to some gears.? or all gears.? (engine running and not)?
3: clutch drags, clutch slips kills all gears, or just 5th.
drag kills them all and reverse 1st , its the canary gear. !! non synchro
4: noise.? or chatter, ****,larchig, or throwout hash ,?

here is the clutch page, link below.

the #1 failure for a gear not Selecting is a $5 fix.
the tip of the shifter shaft, plastic POS is broken, bar none this failure,#1 and sold only at SUZ, get em' while you can they are chapter 11 ANDGM/GEO is brain dead , ask them , and you get blank stares.

this can be proven, by selecting the gears by hand. running.
if failure, cant move those fork rods?
running? only
if you cant, the clutch is dragging. see why?
works stalled means the clutch drags.
can you shift to 1st stalled, start engine drive off can you get any gear? yes,if yes , constantly? with no grinding, the clutch is ok.

to do that manual shifter off test test the shifter must be removed.



the we get to the cable.
see the 1inch rule here, no guessing.
play set to spec, and you floor the pedal , person 2 sees 1 inch travel, (END new cable worry)
if it moves 1inch and the tranny can not be SELECTED.
the clutch is bad, if you can select only stalled motor.
if selection fails all time, stalled and running, the tranny is siezed.
covers every fail logged by 1000s of users

http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

Dec 12, 2012 | 1994 Geo Tracker

1 Answer

Cant select gears in my escort gti, the thrust bearing is winding


this sounds like the throwout breaing is going or gone bad and may have lost it purpose of controling the pressure plate, by not being able to select a gear tells me something has gone bad in the clutch system like the bearing which pushes the pressure plate to release the cluch which allow ****** to stop spinning so that the gear can be selected. the repair for this would be to replace the clutch kit. the clutch pack will come with new bearing clutch disc and pressure plate and if needed a polit bushing, the whining noise was a warning that something in the cluch system was going bad.

Sep 25, 2011 | Ford Escort Cars & Trucks

1 Answer

Cant select 1st gear and if i force it in the car rolls forward like automatic. i have adjusted the pedal and was good for 3 weeks now same problem and no more adjustment? clutch is only 40,000 old


the problem isnt your clutch pedal its either your gear box or your engin revs are to high try putting it in gear using the clutch petal but while thecar is off

Jul 04, 2011 | 1992 Toyota Pickup

1 Answer

Clutch not letting engagement of gears, clutch pedal is soft.


hi first thing to try is to adjust the clutch pedal cable up that is done at the gearbox side by adjusting the 10mm nut on the end of the cable, if after you have done this you can then select gears you will most probably need to replace clutch due to wear.if you cant select any gears even after adjusting the cable then it sound like you have a problem with the selector rod a common fault is for the bushes to wear and knock the selector out of line, check for excessive play in selector rod rubber bush.

Sep 02, 2010 | 1996 Ford Escort 4 Door

1 Answer

Cant select gear


Sounds like a bad or misadjusted clutch.

Jun 29, 2009 | 2003 Honda CR 250 R

1 Answer

Gear box or clutch??


U NEED TO SET THE CLUTCH WIRE BOLT LOSE OR TIGHT IT BOLT IT WILL BE OK

Apr 22, 2009 | 2004 Suzuki RM-Z 250

Not finding what you are looking for?
1994 Yamaha XV 535 Virago DX Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...