Fuel injectors how to remove and clean fuel injectors

Silverado 1500 or 2500 or 3500 or HD? no pickup told
not told the job you are doing>??
remove them all ,or scope them or just what, no job told
no end goal or task told. sorry can guess it.

like most V6/8 now , it is a sandwich.
the service manual covers all,l buy it rent it.?
toss dice and land on 1500
the rail on this engine, fuel rail like all , intake manifold injectors used;. all injector held down by both rails. left and right
now the steps to off them if is the job,
pull the isolator seen photo 1, far below.
1: pull left rail and right rail
Remove and discard the fuel injector retainer clips by installing EN-51097 injector retaining clip installer and spreading both sides of the clip evenly.
Always use NEW fuel injector collars supplied with injector when installing the new injector. If reinstalling the injector, it is not necessary to remove the collars unless the collars are being replaced.
Replace the injector seals as needed. Refer to Fuel Rail and Injectors Cleaning and Inspection.
Note
Inspect the injectors to be sure that they are clean and free of debris prior to installation. Do NOT lubricate the injector seals. Rebuild the fuel injectors whenever the injector has been removed from the fuel injector rail.


now I will past the other page rails off per the manual read to you.
just bank 1, i am to lazy to post both
step 1 rail off bank1.
Note
Inspect the injectors to be sure that they are clean and free of debris prior to installation. Do NOT lubricate the injector seals. Rebuild the fuel injectors whenever the injector has been removed from the fuel injector rail.

1. Remove the fuel pump insulator. Fuel Pump Insulator Replacement
2. Remove the fuel injector intermediate pipe position?1. Fuel Feed Intermediate Pipe Replacement - Position 1
3. Clean the cylinder head pocket around the injectors of any dirt or buildup.
4. Disconnect the electrical wiring harness connectors from the fuel rail.
5. the fuel rail fasteners are retained in the fuel rail by keepers and may be difficult to remove.Remove the fuel rail fasteners?(1) securing the injector rail?(2).
   Install two sets of EN-49248 remover?(3).
6. Install one remover in each of the fuel rail fastener bores.
7. Remove by turning each section of the EN-49248 remover an even amount to pull the fuel rail and injectors out evenly.
8. CAUTION
9. Remove the fuel rail assembly carefully in order to prevent damage to the injector electrical connector terminals and the injector spray tips. Support the fuel rail after the fuel rail is removed in order to avoid damaging the fuel rail components.
10. Cap the fittings and plug the holes when servicing the fuel system in order to prevent dirt and other contaminants from entering open pipes and passages.
11. 1. Simultaneously lift both ends of the fuel rail?(2) and remove the fuel rail assembly from the cylinder head.
12. Remove and DISCARD the fuel injector seals.
13. Some vehicles were not originally equipped with fuel injector dust seals. A NEW seal must be installed when the injectors are removed.
    Remove and DISCARD the fuel injector dust seal (1).
14. NOTE
    Note
    Whenever the fuel injectors are removed from the cylinder head or fuel rail, they will need to be rebuilt. Fuel Rail and Injectors Cleaning and Inspection
    If replacing the fuel injection fuel rail, remove the fuel injectors. Fuel Injector Replacement

Installation Procedure, skipped me. the service manual lists 4 tools
per

Special Tools

1. EN-49248 Injector Rail Assembly Remover
2. EN-51105-1 Injector Seal Installer and Sizer
3. EN-49245-3 Fuel Injection Seal Installer Sizer
4. EN-49245-4 Fuel Injection Seal Installer Sizer

this is first. pull the isolator.

this one step is the GET TO ANSWEREd
Injector work 10x more complex and special tools needed x4

That is a strange issue. Would you tell me more about how the injectors were cleaned? Were the injectors professionally cleaned? Exactly what did you do to clean them? Were the electrical connectors hard to remove or did the wires seem hard and overheated? Was the fuel rail stuck or hard to remove? Why did you decide to clean the fuel injectors? Was it a preventative maintenance or are you dealing with some type of drivability problem? You may want to look at the fuses. Maybe an unprotected wire shorted and blew an injector fuse. The fuel pump may be weak and fuel pressure needs to be confirmed. Did you notice a fuel leak or smell fuel? Please check your engine and fuses and write back. Good Luck.

Cleaning Fuel Injectors - YouTube

? 3:08
https://www.youtube.com/watch?v=MfMkNGlaQZo
Feb 25, 2011 - Uploaded by srmastertech
This video shows an example to what can happen when the fuel filter is not replaced. This vehicle has restricted fuel injectorscaused by excessive dirt in t... ... 2008-2010 Ford Super Duty CabRemoval & Installation Part I ...Missing: baleno

How to remove suzuki baleno blocked fuel injector for - Fixya

www.fixya.com/cars/t10217281-remove_suzuki_baleno

Aug 24, 2011 - How to remove suzuki baleno blocked fuel injector for cleaning. - Suzuki 2001 Esteem question.

Remove the line on top of them and the unscrew like spark plugs u can clean them out with injector cleaner when you reinstall them do not tighten fuel lines all the way leave them loose just a little till fuel sprays out or starts when starts snug each one and crack each one at a time to bleed out the air if it where me I would just put sea foam cleaner in fuse and it won't take long and they will clean up

You have to remove the fuel rail from the engine. Then you can pull out all of the fuel injectors to clean them. Most tune-up shops offer a fuel injection cleaning service that doesn't require removal of the injectors. If your car has high mileage, you can get some extremely good deals on brand new injectors from an on-line retailer, like Amazon.

Clean How?

On a vehicle that old, you remove the injectors
& mail them to a place that ultrasonically cleans them

That is about $45.00 each

There is no fuel line cleaning

You could have them cleaned on the car with the
injector cleaner that is put in a container & pressurized
to at or 5 lbs above rail pressure,the pump fuse removed
& run off that mixture

Don't know what that costs. Say $100.00 or less

The plenum shouldn't be damp with gas. Is it a throttle body fuel injection system?

Could be a leaky injector.

Fuel Meter Body & Fuel Injectors (4.3L Engine) Removal & Installation 1995-2002 Models (RPO L35) To Remove:
4.3L (RPO L35) Fuel meter body assembly

1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
2. Remove or disconnect the following:
   • Upper intake manifold (See: Upper Intake Manifold)
   • Fuel meter body
   • Injector retainer lock nuts (J) and retainer (K)
   NOTE: Use care in removing the fuel injectors to prevent damage to the electrical connector terminals. The fuel injector is serviced as a complete assembly only. Also since the injectors are electrical compartments, these injectors should not be immersed in any type of liquid solvent or cleaner as damage may occur. Fuel injector cleaning is not recommended.
   
3. While pulling the poppet nozzle tube downward, push with a small tip punch down between the injector terminals until the injector is removed

To Install:
4.3L (RPO L35) Fuel meter body assembly

Note: When ordering new fuel injectors, be sure to order the correct injector for the application being serviced.

1. Lubricate the new injector O-ring seals with clean engine oil.
2. Install or connect the following:
   • Fuel injector (L) into the fuel meter body injector socket
   • Retainer (K) and injector retainer lock nuts (J) and tighten the nuts
     1. Torque to: 27 inch lbs. (3 Nm)
   • Fuel meter body
   • Upper intake manifold (See: Upper Intake Manifold)
3. Test drive the vehicle to confirm the repairs.

1993-2005 Models (RPO LU3) To Remove:
4.3L (RPO LU3) Fuel meter body assembly

1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section.
2. Remove or disconnect the following:
   • Upper intake manifold (See: Upper Intake Manifold)
   • Fuel meter body
   • Injector retainer lock nuts (J) and retainer (K)
   NOTE: Use care in removing the fuel injectors to prevent damage to the electrical connector terminals. The fuel injector is serviced as a complete assembly only. Also since the injectors are electrical compartments, these injectors should not be immersed in any type of liquid solvent or cleaner as damage may occur. Fuel injector cleaning is not recommended.
   
3. While pulling the fuel injector downward, push with a small tip punch down between the injector terminals until the injector is removed

To Install:
Note: When ordering new fuel injectors, be sure to order the correct injector for the application being serviced.

1. Lubricate the NEW injector O-ring seals with clean engine oil
2. Install or connect the following:
   • Fuel injector (L) into the fuel meter body injector socket
   • Retainer (K) and the injector retainer lock nuts (J) and tighten the nuts
     1. Torque to: 27 inch lbs. (3 Nm)
   • Fuel meter body
   • Upper intake manifold (See: Upper Intake Manifold)
3. Test drive the vehicle to confirm the repairs

Check this procedure about V8 3.9L Fuel Injectors - Removal & Installation

1. Before servicing the vehicle, please familiarize yourself with safety procedures.
2. Relieve fuel system pressure.
3. Remove or disconnect the following:
   Negative battery cable Engine appearance covers Fuel lines Fuel pressure regulator Fuel cross over elbow Fuel injector connectors Fuel injector clamping plates Fuel injectors

To install:

1. Install or connect the following:
   Fuel injectors. Use new O-ring seals. Fuel injector clamping plates Fuel injector connectors Fuel cross over elbow Fuel pressure regulator Fuel lines Engine appearance covers Negative battery cable
2. Start the engine and check for leaks.
   

1. Before servicing the vehicle, please familiarize yourself with safety procedures.
2. Disconnect the negative battery cable.
   CAUTION The engine appearance cover is equipped with a noise suppressor. If the noise suppressor becomes separated from the engine appearance cover it must be positioned on the intake manifold prior to installing the engine appearance cover.
3. Remove the engine appearance cover and the noise suppressor, if detached.
4. Remove the air cleaner outlet pipe.
5. Release the fuel system pressure.
6. Remove the four engine appearance cover mounting bracket nuts and the brackets.
7. Disconnect the fuel pressure sensor electrical connector from the sensor.
8. Disconnect the fuel pressure sensor vacuum connector from the sensor.
9. Disconnect the eight fuel injector electrical connectors from the injectors.
10. Disconnect the fuel temperature sensor electrical connector from the sensor.
11. Disconnect the fuel supply tube retaining clip from the fuel injection supply manifold.
12. Disconnect the fuel supply tube spring lock coupling.
13. Remove the four bolts and the fuel injection supply manifold and fuel injectors as an assembly.
14. Remove the fuel injectors from the fuel injection supply manifold.
    CAUTION Use O-ring seals that are made of special fuel-resistant material. Use of ordinary O-ring seals can cause the fuel system to leak. Do not reuse the O-ring seals.
15. Remove and discard the 16 O-ring seals from the fuel injectors.
    
    
    

    Fig. Exploded view of the fuel injector mounting-3.9L engine shown
    

To install:

1. Lubricate the new fuel injector O-ring seals with clean engine oil before installing.
   CAUTION Use O-ring seals that are made of special fuel-resistant material. Use of ordinary O-rings can cause the fuel system to leak. Do not reuse the O-ring seals.
2. Install sixteen new O-ring seals onto the fuel injectors. Lubricate the O-ring seals with clean engine oil prior to installation.
3. Install the fuel injectors and clips onto the fuel rail.
4. Install the fuel rail and injectors as an assembly. Tighten the fuel rail bolts to 89 inch lbs. (10 Nm).
5. Install the remaining components in the reverse order of removal.

Keep us updated.

YOU HAVE TO RELIEVE FUEL SYSTEM PRESSURE.REMOVE THE INTAKE MANIFOLD COLLECTOR.REMOVE VACUUM HOSE FROM THE FUEL PRESSURE REGULATOR.REMOVE FUEL HOSES FROM THE FUEL RAIL.REMOVE FUEL RAIL BOLTS AND INJECTOR HARNESS CONNECTORS.REMOVE INJECTORS AND FUEL RAIL AS AN ASSEMBLY.REMOVE INJECTORS FROM RAIL BY PUSHING THEM OUT.REMOVE DISCARD FUEL INJECTORS ORINGS REPLACE WITH NEW ORINGS LUBRICATE NEW ORINGS WITH CLEAN ENGINE OIL.YOU HAVE TO BUY ORINGS FOR FUEL INJECTORS AT THE DEALERSHIP.BESURE TO TAKE OLD ORINGS SO WILL GET THE RIGHT SIZE ORINGS.

The easiest way is to put a cleaner solution in the fuel tank, this will run though the whole fuel system and clean the injectors and lines.
It may smoke a little for a few miles or so, depending on what fuel to cleaner ratio you use, but follow the makers instructions.