Question about 2003 kawasaki KX 125

Open Question

Kawasaki kx80 kickstart sliping

I have to lean my kx to side to kik it off any one know how to repair or fix problem

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: I need to know how to assemble a Kick Start mechanism

Google " Kawasaki KX 80 service manual " You can down load PDF manuals for low cost or get one by ordering. You might want to check out your local library. They somtimes get manuals given to them. It has been 30 years since I have worked as a Kawasaki mechanic but I MAY ( or may not ), be able to help if you could email a clear photo of the parts you have and a clear photo of the inside of the outer case plus a photo of the right inner caseing preferably with the clutch removed.

Posted on Mar 14, 2009

ollie reece
  • 1167 Answers

SOURCE: hey how much and what kind of oil goes in my kx 80

hi mate gear oil wise you need light gear oil i reccomend silkolene,motorex,morris,rock oil for 2 stroke wise you need to buy a mixing bottle of ebay or something with a ratio of 32/1 and i use silkolene comp 2 premix competition oil descent stuff its 10 pound for 1 litre

Posted on Jul 23, 2009

  • 31 Answers

SOURCE: I want to know how to replace the wiring on my

What wiring. The only wiring is for spark.

Posted on Oct 25, 2009

Porrelli
  • 167 Answers

SOURCE: head torqe settings for a 1990 kx 80

8mm bolt 18 ft/lbs

Posted on Nov 23, 2009

Testimonial: "thanks heaps mate very helpful"

searcher1974
  • 229 Answers

SOURCE: my kx 60 wont kickstart but it will bump start

Sounds like low compression. Do a compression test,and it should have at least 90psi,..if not,its time to rebuild the top end..(piston,rings,bore)...pretty common for two strokes.

Posted on Aug 31, 2012

Testimonial: "Cheers pal, I'm gonna have a look at it on Sunday, but it does still run when i bump start it, it has lost a little bit of compression though, but when it runs it still goes into power band and that..."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kymco super 8 2t starts abd runs fine but wont


Scrap the motor and replace complete unit with a decent Japanese motor,eg Kawasaki KX80

Oct 13, 2014 | Motorcycles

1 Answer

Head bolts stripped on kx80 2002


Reline the head bolt holes.Check Timecert.

Sep 08, 2012 | kawasaki Motorcycles

1 Answer

Replacing Kawasaki kx 80 kick start return spring


Hi, easy job, if your bike is waer cooled, you dont say how old it is the old bikes were air cooled, undo all the water pipes attached to the r/h case all the water will escape, you can leave the oil inside the gearbox, if you lay the bike on its left hand side, lift the engine and block it up to make sure gear lever is not resting on the ground, as this will disengage when you remove the clutch cover on the r/hand side, undo all the fixing screws from the cover remove kickstart lever, tap the cover gently to loosen the cover and remove when loose, if the case will not come off check further for screws, sometimes hide inside water pumps etc, once you are ready to remove the cover, keep the kickstart shaft pushed inermost so that it stays located within the engine, once ready fully observe the location of spring mountins within the engine and replace the spring

Oct 17, 2011 | 2003 kawasaki KX 125

1 Answer

I need to replace the cluch cover on a kawasaki kx 80


See: https://www.cyclepedia.com/1988-2004-kawasaki-kx60-kdx80-kx80-kx100-online-manual/

Oct 19, 2010 | kawasaki KX 125 Motorcycles

1 Answer

BARREL APLICATIONS KX 80


Do you by chance mean cylinder head?

If they have the same port locations and same bore dimensions they should be swappable.

You can look online at Kawasaki and see if the replacement parts have the same part number too.

Mar 01, 2010 | kawasaki KX 250 Motorcycles

1 Answer

I have a 1998 kx80 clutch side oil gose low alot and smokes realy bad


then your bearing seal is blown out.
this can happen by too much throttle whit choking.
replace it or fit a new one, its very cheap.

Sep 13, 2009 | 2003 kawasaki KX 125

1 Answer

Please tell me about this dirt bike. 1992 or 1993


VIN:JKAKXWR12PA008201
World region:Asia
Manufactured in:Japan
Year:1993
Make:Kawasaki
Model:KX80-R
Body style:Moto Cross
Drive type:RWD
Cylinders:1 Cylinders

Apr 21, 2009 | 2003 kawasaki KX 125

Not finding what you are looking for?
2003 kawasaki KX 125 Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...