Question about 2006 Harley Davidson XL 1200 C Sportster Custom

1 Answer

Remove the seat to a harley 2008 custom 1200 roadster

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Harley Davidson Expert
  • 125 Answers

If it is a double seat all you do is unscrew the screw at the back of the seat that goes into the rear fender. Then push the whole seat forward and lift to disengage the seat from the horn post (for lack of what they actually call it) and then pull back away form the take to free the tang that fits under the seat.

Posted on Feb 17, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 22 Answers

SOURCE: spark plug

The proper air gap is .032 to .036 depending on spark plug brand.

Posted on Nov 10, 2008

  • 2712 Answers

SOURCE: oil drain plug

Follow the hose that goes to the frame from the oil tank. Loosen the clamp and pull.

Posted on Nov 20, 2008

  • 2 Answers

SOURCE: need instructions on removing back tire on Harley

I worked as a PDI @ riders in b'ham for a while and had to change a few rear wheels, the 1st thing is to deflate the tire then use a coat hanger wire that is strait. Place the wire @ the center of the axel bolt head and then following the swing arm up to the center of the swing arm bolt head, then use a zip tie to mark the coat hanger. Then move to the other side and check to seeif they are the same . They should be. Then move to the disc break and remove the calliper, do not remove the break line. Once you do this you can loosen the axel nut. I assume you have the back tire off the ground, so now you can move the wheel to the front and remove the drive belt. now you can remove the axel and drop the wheel down and out . do this opposit to put it back on remember to use your coat hanger to reset your tension on the drive belt , hope this was helpfull.

Posted on Apr 14, 2009

  • 218 Answers

SOURCE: 2003 Harley Davidson Sportster 1200 Custom Tachometer kit

The only idea that i can come up with is that you dont have a good ground..or the guage was bad when you bought it..i hope this..Keith

Posted on Jul 02, 2009

bozcro
  • 867 Answers

SOURCE: passenger seat on a Harley sportster nightster

main thing befor you drill the mounting hole, make sure its in the middle and the right spot. i did many accurate mods on harleys for ppl because you need a good eye, which most deaalerships dont have. place tape on fender, measure, mark, measure again then drill small hole, check, if good drill full size, if of , drag hole then drill.

Posted on Aug 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Harley Davidson XL 1200 R Sportster Roadster misses on takeoff


Hi, Stacey and the usual suspects are:
1. Throttle cables misaligned or misrouted.
2. Damaged or restricted fuel tank venting system.
3. Intake system air leak.
4. Vacuum piston malfunction.
5. Pinholes or torn diaphragm.
6. Accelerator pump leaking or no output.
7. Plugged bowl vent or overflow.
8. Fuel level in bowl too low.
9. Restricted fuel supply passages.
10. Plugged jets or passages.
11. Worn or damaged needle or needle jet.
12. The enrichner valve/choke not seated or leaking.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Carburator Theory and Tuning
Harley Davidson 2005 Sportster Service Manual
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://mybikemanuals.com/harley-davidson/2005-harley-davidson-owners-manuals
Instant Tech Relief To speak to me personally absolutely "FREE"

Jul 16, 2017 | 2005 Harley Davidson XL 1200 R Sporster...

1 Answer

How do you get the seat off a 2008 Harley Davidson Sportster to change the battery


Hi, Jim seat removal can range from the simple and obvious to the complex and baffling for the novice new Harley Davidson owner. Seems like the more expensive the bike is the harder it is to remove the seat. So let's start with the most expensive. 99% of all Harley seats have a male tongue in the front that slides into a female receiver that is either bolted or welded to the frame just behind the fuel tank. For this reason, whenever you are removing a seat you must always slide it backward 3-5 inches For Heritage Softails check for a bolt on each side usually under a flap on the seat. Then there is the seat strap that is secured on both sides, only one side needs to be removed. A single screw can secure it to the rear fender or it may have a bracket with two studs secured by nuts or knobs to fasten the rear portion of the seat. For Sportsters if you have a pillion pad or passenger seat that snugs up against the front seat there can be a screw securing the two to the rear fender, you have to get your hand in between the two seats and force the separation of seat material to see and gain access to the screw. For Touring bikes, there is the rear seat screw in the back that is the caboose of seat fasteners, usually a large chrome bracket, that screws into the rear fender. Care must be exercised in covering this shiny bauble with your hand during the sliding back procedure so as to "NOT" scratch the tour pack. So when all the hidden and mysterious fasteners have been removed, you need to lift it up in the rear, slide it backward a few inches and bingo you have mastered the impossible.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Harley Davidson Battery Install on Sportster 1200
https://www.carlsalter.com/pdfs/harley-davidson-2010-sportster-service-manual.pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://mybikemanuals.com/harley-davidson/2008-harley-davidson-owners-manuals
Instant Tech Relief To speak with me personally absolutely "FREE"

Apr 02, 2017 | 2009 Harley Davidson XL 1200C Sportster...

1 Answer

Will the 2008 Harley Davidson Sportster 105TH CUSTOM gas TANK fit the roadster?


Hi Marchibeque, 4 ot of 5 Harley Gods give that question a thumbs up, but call your local parts department for confirmation. Good luck.

Mar 21, 2013 | 2006 Harley Davidson XL 1200 R Sporster...

1 Answer

LOCATION OF THE CIRCUIT BREAKER ON 2006 SPORTSER ROADSTER


Look behind the triangular plate on the right side of the bike just under the seat.

Steve

Jul 19, 2011 | 2006 Harley Davidson XL 1200 R Sporster...

1 Answer

N my 06 sportster Roadster tried to crank her up motor turned heard a pop then no lights ,it won't even turn over


There's a fuse panel either under the seat or behind the triangular plate on the left side of your bike. If you find a fuse blown or the main circuit breaker tripped, you'll have to figure out what caused it.

Good Luck
Steve

Jul 15, 2011 | 2006 Harley Davidson XL 1200 C Sportster...

1 Answer

How do you remove the oil tank cover on a 2005 Harley Sporster 1200 XL Custom?


Pull on the bottom of the cover until it pops loose then lift the cover off its two top pins. May have to remove seat to lift off two top pins.

Feb 19, 2011 | 2000 Harley Davidson XL 1200 C Sportster...

1 Answer

How do I remove the negative battery cable to remove the battery for charging on a 2008 1200 sportster custom?


You can charge the battery without removing the battery. Find the large cable that comes from the battery where it connects to the starter. Connect you positive charger clamp there. Connect the negative charger clamp to any good frame ground on the bike. You can charge you battery using this method provided you battery charger clamps are not too big.

If you can't do this, you'll have to take the seat off the bike, remove the battery hold down strap, and then move the battery outwards so you can disconnect the negative battery cable.

Good Luck
Steve

Dec 09, 2010 | 2006 Harley Davidson XL 1200 C Sportster...

1 Answer

Passenger seat on a Harley sportster nightster


main thing befor you drill the mounting hole, make sure its in the middle and the right spot. i did many accurate mods on harleys for ppl because you need a good eye, which most deaalerships dont have. place tape on fender, measure, mark, measure again then drill small hole, check, if good drill full size, if of , drag hole then drill.

Aug 15, 2009 | 2006 Harley Davidson XL 1200 R Sporster...

Not finding what you are looking for?
2006 Harley Davidson XL 1200 C Sportster Custom Logo

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...