Question about 2005 Honda Activa

1 Answer

2005 Honda Activa air-fuel mixture adjustment

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 40,748 Answers

Hi, Anonymous it should be noted that the "AIR FUEL" mixture screw adjustment "ONLY" manages your idle and has no effect on any other circuit also any intake leaks must be repaired before the A/F adjustment procedure can be performed otherwise you will never obtain a proper idle and you will waste a lot of time chasing the impossible. The A/F mixture screw's purpose is to fine tune the fuel charge entering the combustion chamber. The following applies to both 2 and 4 stroke engines:
1. The mixture screw may be sealed at the factory with a Welch Plug please review the following video for removal.
https://www.youtube.com/watch?v=wAXcksgvDkM
2. The mixture screw manages a range of 3 complete 360-degree counterclockwise turns from the bottom/closed position.
3. The mixture screw should have a spring and o-ring for tension and sealing integrity.
4. Turn the mixture screw clockwise until it gently bottoms out, this makes the fuel charge very lean and the engine should not idle if it does then the pilot/idle jet is too big and needs to be replaced with the next size smaller.
5. Turn the mixture screw 1 and 1/2 turns counterclockwise to establish a baseline for starting the engine.
6. To fine-tune the idle circuit, adjust the mixture screw 1/4 turn in or out to achieve maximum idle RPM, wait 15 seconds between each adjustment for the idle to settle.
7. Never go past 3 full turns out this will make the fuel charge rich, foul plugs, and produce black smoke out of the exhaust, if the engine RPM keeps increasing past 3 turns the pilot/idle jet is too small and needs to be replaced with the next size larger.
8. After achieving maximum idle back out the mixture screw another 1/8 of a turn then adjust the throttle cable idle stop screw to 950-1050 RPM.
9. This procedure works great on 99% of all engines, for the 1% that demand a more robust throttle response on aftermarket monster fuel delivery systems additional tweaking outside the box may be necessary.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Adjusting air fuel mixture screw
Honda Activa Fuel Mixture screw Actual Adjustment and RPM Adjustment
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
http://www.partsfish.com/page/oem-parts-for-honda
Honda activa 2009 Owner Manual

Posted on Aug 21, 2017

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

canwoodjc
  • 3301 Answers

SOURCE: 2002 Honda 100R Need

as a starting point, screw them all the way in, "loosely" then out 2 1/2 turns

Posted on Jul 04, 2011

  • 3 Answers

SOURCE: Where is the idle screw, air/fuel adjustment screw on a VT750Cd

It just need to be perfect keep trying different air flows

Posted on Aug 18, 2009

  • 10 Answers

SOURCE: need to adjust my honda shadow 500 vt carburator's

start by synchronizing your throttle plates. Honda calls the next step the "idle drop procedure". u need to know if you have fuel adj. screws or air adj. screws. fuel screws will be on engine side of carb slide, air screws will be on airbox side of carb slide. start leaning out mixture, (turn in fuel screw, turn out air screw. idle will increase so keep adjusting idle back to spec.after each turn if needed. Adjust about 1/4 to 1/2 turn at a time on each carb until there is no change in idle, then richen up mixture by one half turn. If u sync throttle plates first then follow this procedure, there should be no hesitation when you "blip" the throttle, and after revving it should return to idle smooth,

Posted on Apr 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pls help me my Honda activa 125cc air pipe leak petrol heavy petrol leak pls help... I am scared...


Hi, Anonymous and the usual suspects are:
1. Damaged or restricted fuel tank venting system.
2. Loose float bowl screws.
3. Damaged float bowl o-ring.
4. improper fuel level in the float bowl.
5. Worn or dirty inlet valve or seat.
6. Damaged or leaking float assembly.
7. Particle contamination in inlet fitting cavity.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.xbhp.com/talkies/help-me/21532-petrol-drops-leak-over-flow-pipe-activa.html
Honda Activa Fuel Leak
http://www.motorscooterguide.net/Manuals/Honda_CH150_Service_Manual.pdf
http://www.partsfish.com/page/oem-parts-for-honda
Honda Activa Std Dlx Owners Manual

Jan 07, 2017 | 2005 Honda Activa

1 Answer

2005 Honda Activa wiring diagram


Hi, Anonymous first check for continuity at the power and ground wire at the horn, then check for continuity at the horn button, back in the day there was a small adjustment screw on the back of the horn, by turning it one way or the other you could set the limit on how much the diaphragm vibrated.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2005 Honda Activa wiring diagram Google Search
Honda Motorcycle Wiring Diagrams
Honda Activa Scooter Horn not working
Learning to repair the horn of Two Wheeler Hindi
Honda Activa 2011

Sep 18, 2014 | 2005 Honda Activa

1 Answer

2013 Honda Activa will not idle when warm


Hi, Anonymous you need to make sure you have no intake leaks by spraying some Brake Kleen, Contact Cleaner, Starting Fluid etc. around the intake manifold and seals, if the RPM's go up or down significantly then you have a leak that needs to be fixed before you can continue with the carburetor adjustment.
The engine should be at operating temperature with the enrichener off to set the idle between 950-1050 rpm. Turn the idle skrew clockwise to increase the idle speed and counterclockwise to decrease the idle speed. If you have access to your air fuel mixture skrew you may turn it as well, if not there is a video below on how to gain access, make sure you start with clean or new spark plugs. Gently turn the air fuel mixture skrew clockwise until it starts to bottom out "STOP" do not over tighten as it will damage the taper on the end, now back the skrew out 1-1/2 full turns to establish a starting point start the engine and check the idle rpm's and turn the idle skrew accordingly for 950-1050 rpm if necessary, turn the air fuel mixture skrew 1/4 turn at a time and let the engine settle for about 10 seconds, turn the skrew clockwise for a leaner mixture and counterclockwise for a richer mixture, you are seeking the highest rpm your air fuel mixture skrew can acquire without going past 3 full turns from bottom then resetting the idle skrew back down to 950-1050 rpm If you can not detect any rpm change and can not stall the engine by turning the air-fuel mixture skrew all the way in then your pilot/low-speed jet is too big and needs to be replaced with the next size smaller. Final adjustment should be made with a clean air filter mounted to the carburetor.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Honda Activa 2013 Engine Stalling
Honda Activa Engine idling stalling issue caused by faulty ring fitment...
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
http://www.partsfish.com/page/oem-parts-for-honda
Honda activa 2009 Owner Manual

Jun 28, 2014 | 2011 Honda Activa

1 Answer

2013 Honda Activa will not idle when warm


Hi, P and the usual suspects are:
1. Idle speed improperly adjusted.
2. Air fuel mixture screws not properly adjusted.
3. Inlet system air leak.
4. Leaking accelerator pump.
5. Loose low-speed jet.
6. Plugged low-speed jet.
7. Contaminated or plugged low-speed circuit.
8. Enrichner valve/choke not seated or leaking.
9. Multi carburetors out of sync and need to be balanced.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Honda Activa 2013 Engine Stalling
Honda Activa Engine idling stalling issue caused by faulty ring fitment...
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
http://www.partsfish.com/page/oem-parts-for-honda
Honda activa 2009 Owner Manual

Jun 28, 2014 | Honda Activa Motorcycles

1 Answer

Where is the throttle screw(for idle speed), of the carb, in honda activa


That idle adjustment screw you are looking for can be found just below the fast idle cam. Which is connected to a spring-loaded hinge with a throttle cable attached.

Jan 22, 2014 | Motorcycles

1 Answer

Honda 25 cc 4 cycle mini tiller how to adjust carburator


With one screw you can adjust the idle speed, and with the second, located under the carburetor you can adjust the running or load speed.

Mar 22, 2013 | Honda 25cc 4-cycle Mini Tiller

1 Answer

Need to adjust my honda shadow 500 vt carburator's fuel/air mixture


start by synchronizing your throttle plates. Honda calls the next step the "idle drop procedure". u need to know if you have fuel adj. screws or air adj. screws. fuel screws will be on engine side of carb slide, air screws will be on airbox side of carb slide. start leaning out mixture, (turn in fuel screw, turn out air screw. idle will increase so keep adjusting idle back to spec.after each turn if needed. Adjust about 1/4 to 1/2 turn at a time on each carb until there is no change in idle, then richen up mixture by one half turn. If u sync throttle plates first then follow this procedure, there should be no hesitation when you "blip" the throttle, and after revving it should return to idle smooth,

Apr 08, 2010 | 1986 Honda VT 500 C Shadow

2 Answers

How to open dome of honda activa for clean spark plug


You need to open the seat of honda activa and open the screw present in the space provided for tool kit and helmet. Next remove the two screws holding the back rest (the ones above the tail light). Now just lift the body by holding the front end (the one which is towards the steering) there will be a rod below pull it up and let it the body rest on it. You will find the spark plug on the side of the engine (you need to pull out the cap housing the spark plug).

Jun 14, 2009 | 2005 Honda Activa

1 Answer

1989 accord lx, idles high at start-up, now it won't stay running


Carburated engines of that year may have an idle screw adjuster. You can see the screw from the outside of the carb. If so, try adjusting the carburator with a screwdriver. Unlike fuel injected Engines they can be manually adjusted.

Apr 08, 2009 | 1991 Honda Accord

Not finding what you are looking for?
2005 Honda Activa Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...