Question about Loncin Motorcycles

Open Question

Loncin atv 200cc crossrunner

What is the valve clearance settings? I have read several different settings but not sure which one is right. Most 200cc say .004 Int/.006 Exh. is this correct?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: is my 1986 honda atv 200cc a 2 stroke or a 4 stroke?

Four stroke.

Posted on Apr 11, 2009

  • 3567 Answers

SOURCE: 04 crf 250r.... the head has a chattering noise when running

Any chance the valve spring has collapsed? Cam shaft thrust washers missing? Cam shaft bearing gone bad?
abe5193.gif b3c3550.gif Please rate this solution. Thanks!

Posted on Jun 22, 2009

dmsr63
  • 2050 Answers

SOURCE: what is the correct valve clearance of motorcycles

The YZ 125 does not have valves. It's a two stroke engine.

Posted on Jan 05, 2010

  • 4088 Answers

SOURCE: Clearances Thresholds

Other than the valve will be slightly noisier, no harm will be done.

Posted on Jan 30, 2010

agent91
  • 2100 Answers

SOURCE: I'm checking valve clearances on a 2001 st4 and

Yes, you have 4 valves per side, 2 are intake, 2 exhaust. On the intake, the opener is .002-.007, and the closer .006-.010 , The exhaust, opener is, .002-.009 and the closer is ,.004- .008. If you are planning on doing this yourself, you need to do your math and get the right shims, Ducati will sell you the shims you need, but there are other people out there making them. When measuring the clearance, you need to turn the engine over by hand, pull the plugs, pull the cover off the left side to get to the crank bolt, get a friend to crank the engine over while you runs shims in and out of the rockers, keep notes on your measurements.

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find an accurate diagram for a 48cc Loncin mini chopper


Hi, Toby for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
loncin mini chopper wiring diagram Google Search
Chinese ATV Wiring Diagrams for Loncin Engine Powered ATVs and Dirt Bikes...
LONCIN 48cc Mini Chopper engine PLEASE HELP
http://www.miniriders.com/tech-talk/29110-pit-bike-repair-parts-manuals-exploded-views.html
FS517 49cc Super Chopper parts ScooterParts4Less com

Jan 28, 2017 | Loncin Motorcycles

1 Answer

Chinese 110cc loncin motor LC 152 fmh. Where can I get an exploded view?


Hi, Ernrst for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" stuff that you will need please click on the blue links below. Good luck and have a wonderful day.
Chinese ATV Wiring Diagrams for Loncin Engine Powered ATVs and Dirt Bikes...
Chinese 110cc loncin motor LC 152 fmh Where can get an exploded view...
http://www.budgetatvs.com/downloads/ATVs/Service%20Manuals/110cc%20&%20125cc%20Service%20Manual.pdf
Exploded Parts View for Loncin Engine Powered ATVs and Dirt Bikes...
http://www.rpmfactor.com/motorzone/ATV_110manual.pdf

Jun 24, 2015 | Loncin Motorcycles

1 Answer

99kawasakiprarie300valveadjustment


MOVE EACH CYLINDER TO TOP DEAD CENTER OF COMPRESSION STROKE ( sorry caps on .) check that timing mark in timing cover hole is in line .remove adj cover per cylinder in alignment and adj valves according to mfg specs. to adj : under adj cover , loosen lock nut on top then loosen adj nut on btm @ top of valves . insert feeler gauge under rocker and adj ,this is tricky to say the least. usually takes several tries to get it right, keep trying the valves must be set right or major expenses can be expected to occur. intake and exhaust settings are different normally at least .005 .be sure to tighten locknut on top before checking if clearance is correct. holding the btm nut while turning the locking nut is the tricky part 4 me anyway. 2 valves per cyl. on most atv eng. adj all valves .start eng and listen to eng w/o reving up. any ticking noise and you get to start over. should be smooth idling and quiet. no popping or backfiring. smooth starting and off w/o run on. should not be performed unless you are familiar with the procedure. contact me or service center near you if not sure on procedure.correct adj. is slightly snug fit . valves making no noise when done .

Jul 12, 2014 | ATVs

1 Answer

'92 yamaha timberwolf valve adjustment


Here's the info you're looking for.

1992-1998 Yamaha Timberwolf 2WD and 4WD
Intake: 0.05 - 0.09 mm (0.002 ~ 0.004 in)
Exhaust: 0.11 - 0.15 mm (0.004 ~ 0.006 in)

Jun 20, 2014 | RTO 200cc Full Size Four Wheeler ATV

1 Answer

Arctic cat problems


Check for spark if it has spark your carb may be dirty or not jetted right if it's not your carb or spark your valves may need to be adjusted

Dec 22, 2013 | RTO 200cc Full Size Four Wheeler ATV

1 Answer

What is the valve clearance for a yamaha moto 4 200cc atv


1st. change oil and filter.. use 10-40.. if that doesn't quiet them... .0025"-.003" on intake .004" - .005" exhaust should do it... if they are too tight,,it won't idle down fast or well.... or excessively tooo tight -won't start..too loose they rattle or if there is a lot of wear.. the rocker arms may need replacing

Apr 17, 2012 | RTO 200cc Full Size Four Wheeler ATV

1 Answer

Yamaha grizzly 600 not firing


Check spark clean the carb check valve clearances if none of those you have an electrical problem

May 16, 2010 | RTO 200cc Full Size Four Wheeler ATV

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Loncin Experts

RAYMONDO1953

Level 2 Expert

545 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Donald Gunn

Level 1 Expert

54 Answers

Are you a Loncin Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...