Question about Not available Renault ING Racing Jacket Black with Orange and White

1 Answer

Removing engine in 1998 chevy malibu

Removing engine from 1998 chevy malibu

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 507 Answers

Buy the Chilton's manual and read it................

Posted on Jul 04, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is transmission stick located on a 1998 Chevy Malibu automatic


The 1998 Chevy Malibu does not have a transmission dipstick. Although there is a check plug located on the transaxle, near the pan, adjacent to the engine oil drain plug.

Jun 13, 2013 | Cars & Trucks

1 Answer

Need steering pump hosed replaced 1998 chevy malibu 3100 engine


may want to remove the ignition coilpack for more access to the nut on the rack, thats the hardest part of the job, then remove the hose retainig clip on back of the alternater and remove the steering pump bolts thru the pulley to lift it up so youll have clearance, but the fuel injection check port usually gets in the way so try carefully prying

Dec 30, 2012 | 1998 Chevrolet Malibu

1 Answer

Where is the crank positioning sensor located on a 98 chevy malibu 4 cylinder


if a 2.2 four-cylinder, remove the starter motor. disconnect the 7x crankshaft position wiring and harness connector. remove crankshaft retaining bolt and withdraw sensor from engine block. replace the "O" ring and lightly lubricate it with new engine oil. installation is reverse of removal. have a good one !!

Oct 24, 2010 | 1998 Chevrolet Malibu

1 Answer

Location of water pump on 1998 chevy malibu with 2.4 twin cam engine


your water pump is driven off of timing chain,it will be on back side of timing cover toward firewall down toward bottom. you have to remove timing cover and chain to replace pump

Aug 21, 2010 | 1998 Chevrolet Malibu

1 Answer

Ho do you remove oil pan on 1998 chevy malibu 3.1


take out the oil pan bolts and take it out might have to undue motor mounts and jack up engine to get pan out.

Oct 04, 2009 | 1998 Chevrolet Malibu

1 Answer

98 chevy malibu:engine wont turn


Check with a battery tester if you have power at the starter, Are the Battery post clean, Are any fuses blown in the fuse Box, check for any corrision.

Aug 13, 2009 | 1998 Chevrolet Malibu

2 Answers

Where is the water pump located on a 1998 chevy malibu 4 cyl?


It is located at the rear of the engine between the timing cover and exhaust manifold. You will have to remove the manifold to ge to pump. It runs off the timing chain. It would be a wise decision to take to an experienced mechanic.

Jul 02, 2009 | 1998 Chevrolet Malibu

2 Answers

Bad knock sensor on 1998 chevy malibu 2.4L


The knock sensor is on the back side of the engine near the trans. It is round, with a 1 wire connector. You will have to get it from underneath. Good Luck.

May 06, 2009 | 2008 Infiniti FX35

2 Answers

Serpentine belt 2000 chevy malibu putting one on


first of all,put a jack under engine, put wood on top to prevent from hurting engine,jack up till a little tension is on jack to support engine.release tensioner, a 3/8 breaker bar will work in the square part of tensioner.next remove cruise control from braket and set aside.remove motor mount.if need be, jack engine up to remove belt. 3.1 v6

Oct 31, 2008 | 1998 BMW M3

Not finding what you are looking for?
Not available Renault ING Racing Jacket Black with Orange and White Logo

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Not available Experts

BJ Russell

Level 2 Expert

214 Answers

yobo007
yobo007

Level 3 Expert

507 Answers

Alan Springett

Level 2 Expert

91 Answers

Are you a Not available Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...