Question about Motorcycles

Open Question

Bajaj wave scooter spares

Head light set, front fork set

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: i would like to know how to change the front forks on my burman

To remove the forks you need to untighten the screws holding the forks in the yoke, then hit the tops of the forks slightly with a wooden hammer to get them out of the yoke.

Posted on Jun 15, 2009

  • 2 Answers

SOURCE: Bajaj Saffire Automatic Transmission

Throw it

Posted on Oct 23, 2009

  • 3567 Answers

SOURCE: My Bajaj Wave DTS-I does

Get a new spark plug and clean or replace the air filter. Drain the carb and then refill it. Now check for spark by putting the plug wire on the plug then holding the metal side of the plug against the cylinder head. Use the starter to turn the engine over so you can look for spark at the end of the plug. Check the fuses with a multimeter. If still no spark, check the kill switches. Be sure there is gas in the tank and the gas flows freely into the carb.

Posted on Sep 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change steering head bearings


If bearing races are removed, the bearings cannot be reused, they must be replaced.
1. Support motorcycle so front end is off floor and forks are fully extended.
2. Remove right side cover and remove maxi-fuse.
3. Remove headlamp and headlamp bracket.
4. Remove both front brake calipers.
5. Remove front wheel.
6. Remove front fender bracket with front fender.
7. Loosen but do not remove fork tube caps.
8. Loosen all pinch bolts on top and bottom triple clamps and pull fork tubes from triple clamps.
9. Remove brake hose bracket from the bottom of fork stem and bracket.
10. Remove fork stem cap and remove fork stem nut.
11. Lift handlebars from steering head with upper triple clamp attached. Be careful not to pinch or kink control cables.
12. Remove adjusting nut, seal, and upper bearing out of bearing race.
13. Pull fork stem and lower triple clamp from bottom of steering head.

Jul 14, 2014 | 2008 Harley Davidson VRSCDX Night Rod...

1 Answer

Harley has front end clunk


Hi Anonymous, unless you are having handling issues it's probably the front forks not having correct fork oil amount or the wrong weight, for more information on your question please visit the websites below and good luck: Harley Davidson Manuals Mark Workshop
Cycles Capacities and Fluid Requirements Fork Filling Quantities
How to Change the Fork Oil on 2012 Harley Davidson Street Glide

Dec 16, 2012 | 2005 Harley Davidson FLHRS - FLHRSI Road...

1 Answer

Torque setting 1999 300 ktm head &side cover


Thank you for contacting FixYa with your inquiry. I have been going over some of the inquiries that have been archieved and trying to provide solutions for those that didn't get answered. Hope this information helps.


KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

Oct 29, 2011 | Motorcycles

1 Answer

How to change head set also replace front fork?


Loosen clamp at top of bike frame where seat slides in ...twist seat back and forth while lifting upward.......To remove ft. fork ..At handlebar assy.remove allen bolt..(some are hidden by rubber plug)..remove handlebar assy/remove large nut at top of frame where handlebar slides down in..
...twist and pull to remove front fork....some have upper and lower nut depending which bike.

Feb 27, 2011 | Cannondale Jekyll 600

1 Answer

2009 ktm 125sx torque settings for head and cylinder


Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

TF

Nov 05, 2010 | 2008 KTM 125 SX

1 Answer

Wobble at above 65


Better start checking everything. depending on the severity of the wobble, it may just need something simple like a new tyre. But all of the following can cause a problem
Tyres worn
tyre pressures\and balance\incorrect sizes
wheel bearings front and rear
spoke tension( if it has spokes)
Head bearings\twisted forks
swing arm bushes
change front fork oil\check suspension settings
loose axle bolts
bent discs
string line the wheels
bent frame or forks

Apr 25, 2010 | 2004 Harley Davidson FLHT - FLHTI Electra...

1 Answer

Head tourque wrench setting


Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs
TF

Apr 19, 2010 | 2005 KTM EXC 200

1 Answer

How to replace the fork seals on a 2003 harley davidson fatboy


If you ask this question YOU should not be doing it! but your *** on the seat not mine.
Remove ...........front wheel, front fender,top fork cap and loosen lower triple clamp bolts under head light cover, forks are now out!
Remove 6mm bolt at the bottom of the fork leg and drain oil,remove dust seal and wire clip, now remove the upper fork nut (the spring will jump out at you).Pull the leg and tube away from each other, the old seal will stay on the tube..clean and reassemble driving NEW seal down into place with wire clip.....refill with oil

Mar 31, 2010 | 2003 Harley Davidson FLSTFI Fat Boy

1 Answer

Feels like type of tank slap when cornering checked tyre headstock tension wheel balance tyre pressures bearings it is the only bike iv'e ever owned that i can not remove my hands from the bars whilst in...


Jack up the front end until the wheel is off the ground, then slowly rotate the bars from one stop to the other. If you hear noises or it feels rough, take the forks and wheel off, disassemble the fork head and inspect the upper and lower bearings and races for damaged surfaces. Clean and repack bearings with fresh grease. Reassemble the fork head and adjust the bearings to just remove slop. Recheck the rotation. When putting the forks and wheel back, check the shock action of each fork individually. If the machine has a lot of miles, drain the fork oil and recharge. Make sure that the axle is clamped tight as well as the fork head clamp and top bolts. Has the bike ever been hit hard in the front? If yes, it could have changed the fork angle making it unstable.

Aug 22, 2009 | 2006 Honda VT 750 Shadow

1 Answer

Distinct front fork knocking


Put the bike on a stand and grasp the forks at the bottom and push in / out to see if there is any play also check pads in the caliper and brake hose knocking against fork leg etc. if you dont have a stand (or a milk crate) you can sometimes feel play by rocking the bike back and forwards with the front brake applied. Other things to check are that the front tyre pressure isnt too hard .. and I would suggest you bleed the air out of the forks via the top philips screw ,

Nov 10, 2008 | 2007 CCM 404 Enduro

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...