Question about kawasaki GPZ 1100 Motorcycles

1 Answer

Hydro clutch hydro.clutch adjustment

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

There is no adjustment on the hydraulic clutches...if it drags, bleed the system and check slave piston for leaks...if it slips, check that the piston in the slave isn't sticking...if that's ok check the friction plates for wear.

Posted on May 09, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 20 hp mahindra tractor with front end loader the problem I am having is it will not go up a slight hill in forward or reverse what can I do thank you

If it is a hydro or automatic it sounds like you need to check fluid levels, if manual trans you may need a clutch or clutch adjust

Dec 12, 2016 | Garden

1 Answer

Mowcart 66 break/clutch dosnt work properly and chain keeps coming off

Loosen adjuster plates where rear axle mounts to frame,they should be elongated slots to allow chain to be adjusted and alig ned,you can also adjust belt under body for clutch/brake function..

Jul 25, 2014 | McCulloch Riding Mower Briggs 20 HP V-Twin...

1 Answer

I just changed teh clutch plates on my Honda CFR450R and now I do not have any action in my clutch lever. Is this clutch hyro assisted. If it is where can I bleed the air our and get my clutch lever...

If it has a clutch cable and not a pipe then you need to look at clutch assembly ,cause it could be that the clutch plate is put the wrong way in,thus not putting pressure on pressure plate or pressure plate is shot and needs to be replaced.If it is Hydro then it will have an hydro pipe and a container for brake fluid level

Dec 28, 2013 | Yoshimura Large Engine Plug HONDA CRF450R

1 Answer

I have an ATV 2000 Yamaha Kodiak YFM400AM(C). A few months ago after warming up it stalls when I PUT IT IN GEAR. I had to adjust choke idle up to engage into gear and go. It still does that and now when I...

For the first problem. Most likely the clutch is holding to tight and needs to be adjusted. Next problem. Check this first. Check the
connections on the battery post, make sure they are clean and tight. Next the carburetor may have flooded and hydro locked the piston. Make sure the battery is fully charged and the battery post are clean and tight. Retry starting the engine, if you only have the clicking sound, move the ATV to a location where gasoline cannot be ignited by a flame or spark including the sparkplug wire. Remove the sparkplug, move the sparkplug wire into a location where it is not close to ground so it will not create a spark. Try to crank the engine and see if it will spin, if it spins it will spew out gas if it was hydro locked. If the engine was hydro locked crank the engine a little more expelling as much gas as possible. Leave the spark plug out for a while so the remaining
gasoline in the cylinder will have time to evaporate. Clean and
reinstall the sparkplug. Try starting the engine, if the engine starts, reset the adjustments you made to the carburetor prior to having the dying problem. If the engine was not hydro locked and will not spin, and you only hear the clicking sound when trying to start the engine, you may have a problem with the starter or starter solenoid should it have a solenoid. I do think the engine will be hydro locked. Provided the battery, was fully charged the battery terminals were clean and the starter circuit is ok.


Oct 30, 2013 | 2004 Yamaha XT 660 R

1 Answer

The clutch on my 1986 nissan pickup engages at the very top of the pedal. How do i adjust it

I have A 91 Nissan pickup with a hydro clutch and I adjusted it by threading out the threaded rod at the top of the clutch peddle inside the cab I hope that helps

Sep 16, 2012 | Nissan Cars & Trucks

1 Answer

How to adjust the clutch on ariens hydro 42

If you need the clutch adjusted there is a specific sequence for adjusting the clutch.I would spray with WD-40 or penetrating oil on the clutch movement , on the shaft (just in front of the engine) under the belts, there is only about 1/4" or so movement. Also lube all the linkage pivot points. If you still need to adjust the clutch download the manual with the model and serial number from and follow the procedures in the manual.

Apr 02, 2012 | Garden

1 Answer

I need help to adjust my hydro clutch on 2007 1800c vtx

Hi Satanonwheel, for more information about your question please visit the website below. Good luck and have a nice day.
2007 Honda Motorcycle Service Repair Workshop Manuals

Apr 13, 2011 | 2007 Honda VTX 1800 C

1 Answer

Engine wont turn over due to the clutch not able to depress far there an adjustment for this if so where and how...thanks

sounds like you need to replace the clutch safety switch sound like the contacts inside the switch have went bad . I don't think you can adjust those due to it being a hydro system . Hope this helps out!

Jun 05, 2009 | 1991 Ford F250

1 Answer

I have a snapper rider (hydro), when it's started and u take foot off clutch/brake, it dies, push in clutch again and it catches...could it be the safety switch under the seat? Please help!!!

This does sounds like your safety switch is bad. But you do need to make sure that your clutch it engaging properly also the adjustment could have been changed by vibration also

Apr 13, 2009 | Garden

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4533 Answers


Level 3 Expert

76630 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides