Question about 2002 Harley Davidson FXDL Dyna Low Rider

1 Answer

Replace ignition switch

You tell me!

Posted by Anonymous on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 50 answers of more than 400 characters.

  • Harley Davidson Expert
  • 300 Answers

1. Remove seat.
Always disconnect the negative cable first. If the positive
cable should contact ground with the negative cable
installed, the resulting sparks may cause a battery explosion
which could result in serious injury.
2. Disconnect battery cables, negative cable first.
3. Unscrew ignition/light lock ring. Push switch back through hole.
4. Cut switch wires approximately 3.0 in. (76 mm) from switch body. The new switch must be spliced into existing wiring harness using splice connectors.
5. After splicing new switch into wire harness, place switch into position. The word "TOP" is marked on the top of the switch body to allow for proper positioning of switch. 6. Install lock ring to secure switch in place.

Posted on Mar 27, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Remove ignition switch

Having the replacement switch you tell you a lot having a active key to turn to on position with help you depress the button on the switch in order to release the switch from the housing removing the any covering around the ignition might be required as well in order to get to the release button located on switch. Again your new switch will aid in this

Jan 15, 2014 | 1992 Lexus Ls 400

1 Answer

I need to replace the ignition switch in my car

There is an Ignition switch that is located under the dash. On the other hand if your referring to where the ignition key goes in then this part is called an ignition cylinder. If it is the ignition cylinder (or tumbler) then yes the steering wheel must be removed to replace this and you will need special tools to do it. I would not suggest doing this yourself with no experience as there are lots of small pieces and parts in there. The ingition switch is located under the dash on the steering column and has a wire harness attached to it with numerouse wires. This is replaced by removing 2 small bolts and unplugging it. There is a rod running down the column that goes into a slot on the back side of the ignition switch. It must be placed in the hole where the old old was and then the switch may need adjusting forward or back to properly work.
Hope this helps.

Apr 10, 2013 | 2000 Cadillac DeVille

1 Answer

Digram of replacement ignition switch

please tell me the year make and model of vehicle, and if 4x4, automatic or manual transmission and engine size if possiable and i will send you a link or pic's of this requested information, thanks

Jul 15, 2012 | GM Carts Car Audio & Video

1 Answer

How to fix ignition switch

I can help you. however more info is needed, please tell me the vehice make, model, and year. Also the ignition switch your refering to is the electrical portion of a ignition lock assembly, if the vehicle has a standard lock that uses a key, (not push button start). if the lock is damaged or no keys...then the part you need is a ignition lock and key, not ignition switch, :) *some imports have this assembly, lock and switch as a unit*, and are not servicable, in this case the entire ignition assembly will be required.

Jul 15, 2012 | Cars & Trucks

2 Answers

When trying to light oven or grill the clicking of the ignition does not stop! Any ideas? Parkinson cowen chichester thanks

your oven switch is sticking, causing the clicking, if you can open the range top to see that switch, i would pull off the wire to that, until you can have it replaced

Dec 19, 2010 | Microwave Ovens

2 Answers

How to replace ignition switch

I purchased an ignition switch for my 2002 Oldsmobile Bravada and It needs replaced.Please tell me the best way to remove the steering column to replace it. The Auto parts store said it would be simple. I have worked on cars and helped build cars but I haven't put in an ignition switch. I have it started.Please help.

Oct 20, 2010 | 2002 Oldsmobile Bravada

1 Answer

I have a 2004 hyundai accent. the starter went bad two weeks ago, and a friend and I replaced it. (it wnt without warning ) The other day, it went again. I'm told it could be in the ignition. That it's not...

if this starter "went bad" by refusing to work (run)
replace your ignition switch: it's behind the ignition lock on the steering column.
ignitions do not tell starters to do anything: the ignition switch key turns the starter on and, a spring returns the key to off when you release it turning the starter off.

Jul 19, 2010 | Hyundai Motor 2004 Accent

1 Answer

Was replacing the ignition switch and accidently broke off a silver piece off of where the switch goes connected. Can you some one tell me if this can be replaced and if I have to replace the entire key...

Replacing An Ignition Switch..

If The Ignition Switch Is Defective, It Must Be Replaced Regardless. Before Removing A Dashboard-mounted Switch, The Tumbler (Lock Mechanism) Must Be Removed From The Switch.Normally A Small Piece Of Wire Is Inserted Into A Hole IN The Front Of The Switch And The Key Is Turned.This Will Release The Tumbler From The Switch So The Tumbler Can Be Pulled Free. Then Unplug The Wires And Remove The Old Switch.

A Steering Column-mounted Ignition Switch Is Separated From The Tumbler. It Is Normally About Halfway Down And On Top Of The Steering Column. To Remove This Type Of Switch, Remove The Fasteners Holding The Steering Column To The Dash. This Will Let The Column Drop Down So You Can Replace The Ignition Switch.

Apr 09, 2010 | 1999 Dodge Caravan

Not finding what you are looking for?
2002 Harley Davidson FXDL Dyna Low Rider Logo

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

4340 Answers


Level 3 Expert

76846 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides