Question about Harley Davidson Motorcycles

1 Answer

2013 street glide abs light stayes on i just added new wheels and rotors what is the problem

2013 stret glide abs light stays on.I just changed the wheels and rotors what could it be

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 43,029 Answers
Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: ABS light flashs - push switch and it stays on completley

it is caused by low battery voltage run bike for about a mile then stop turn of turn back on wait till abs lights go out then start

Posted on Apr 14, 2009

  • 3 Answers

SOURCE: 2006 Harley Street Glide turn signal problems

hi, if you have not yet fixed the problem , the fuse box is located underneath the left sidecover in front of the left sattlebag youll need to remove the bag to get the side cover off ck the fuses thats all it should be ,prolly what happened was a bulb went bad and shorted the circut blowing the fuse for them theyre on the same fuse as the tach and speedo

Posted on Apr 27, 2009

v2iper
  • 150 Answers

SOURCE: I need the torque specifications for the rear

Your wheel is 95 to 110 ft lbs

Brake Disk is 30-45 ft lbs ( lock tight)

Pulley i( belt Sprocket) is 55-65 FT Lbs Lock tight red on both.

Posted on Jun 15, 2009

  • 13 Answers

SOURCE: My check engine light goes on sometimes and then

on your dash is the button to check your milage. push it in and hold it down until your codes come up. some of the numbers it will go through will only be ecm numbers

Posted on Oct 09, 2009

Testimonial: "exactly what I needed. Thanks,"

wd4ity
  • 4565 Answers

SOURCE: 2006 Harley Davidson street glide brake light

Try loosening the bolts holding the front master cylinder on the handlebars. Slide the master cylinder down as close as possible to the right handlebar switch housing. If this doesn't work, the front brake light switch is probably bad and needs to be replaced in the right switch housing.

Good luck
Steve

Posted on Sep 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHY THROWING abs brake codes


If you changed from the proper engineered stock wheel and have not had the ABS reprogrammed this would be why but H-D will only have an ABS program for their deswigned part combinations in any case.

Apr 25, 2014 | 2011 Harley Davidson FLHX Street Glide

2 Answers

ABS light stays on 2008 street glide after putting on a 21 inch DNA


check for broken wire to the sensor rotor at each wheel
check that the inner part of the rim has not worn through the wiring to the sensor.

Jan 03, 2014 | Harley Davidson Motorcycles

1 Answer

Abs light stays on, got new brake pats and rotors... still stays on! noise when braking.


you will need to have someone scan the abs systen with scanner to pull codes to know what wheel sensor is the problem

Nov 13, 2010 | 1999 Ford Explorer

1 Answer

I replaced my brake rotors on a 2004 gmc canyon and installed new brakes. everything works great, however my abs light stays on now.


IF you installed the wrong brake rotors,without the ABS reluctor ring[if equipped],the light will come on.Second possibility is you damaged the ABS wiring to the wheel speed sensor.There is a harness to each wheel.

Apr 17, 2010 | 2004 GMC Canyon

1 Answer

2007 road king police abs light stays on


with most ABS light stay means a problem.

most of the time the wheel speed sensor.

2 wire connection to pick up coil (transducer)

what is located near the axle hub.

may be not getting signal from open circuit

or transducer to far away from ring

Jul 29, 2009 | 2008 Harley Davidson FLHX Street Glide

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...