Question about Motorcycles

1 Answer

2004 hyosung gt 250 wong go forward, on blocks the tire moves and it shifts the gears, though it can be stopped with my foot. already tried adjusting the clutch cable, still no torque

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 22 Answers

If the engine keeps running when you stop the tire the clutch is worn out or not engaged.

Posted on Feb 10, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 12 Answers

SOURCE: My bike is clutched

shift fork in trans is not engaging need to let someone open trans and sovle the issue those trans are not hard to fix but if you dont know how the shift fork needs to be to fuction seek pro help

Posted on Jun 09, 2009

  • 9 Answers

SOURCE: Clutch slipping

bad news. a goodly amount of 2004's came out of the factory with faulty clutches.. there's been several efforts by rebel owners to get a recall on them, but no luck so far. hope that's not what it is, but bear it in mind if you find your top speed dropping.

Posted on Jul 21, 2009

  • 3567 Answers

SOURCE: recently snapped my clutch lever off my kx 250

Be sure you were given the correct cable, The stock cable is part number 54011. Compair the old cable to the new one.

d9b88da.png

Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 ,250 twin carb hyosung ..need to know how to readjust the carb screws so it stops stalling when given gas


Hi, Cathie and the usual suspects are:
1. Idle circuit and transfer ports clogged.
2. Air fuel mixture adjustment too lean.
3. Pilot jet clogged.
4. Faulty accelerator pump.
5. Float level too low.
6. Float bowl contaminated old fuel, water, dirt, rust, etc.
7. Float bowl vent or overflow tube clogged.
8. Fuel flow to carburetor restricted.
9. Intake manifold leak.
10. The gas cap is not venting properly or fuel tank venting system blocked.
11. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
12. Needle and seat stuck closed in the float bowl.
13. Multi carburetors not in sync.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://korider.com/index.php?topic=19379.0
hyosung gv250 carb balance with 2 bottle manometer
http://files.hyosungmotorsusa.com/GT125_250_Service_Manual.pdf http://www.alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 125R Manual

Jun 01, 2017 | 2005 Hyosung GT 250

2 Answers

Bike will not move forward when put into gear


u need to git a clymer manual for complete repair--sounds like the clutch needs replacin or repair--disengages ok but the plates are not grippn--dont bring it to a dealer-go private if need--isnt that hard of a job-but special tools probly needed

Feb 09, 2014 | Motorcycles

1 Answer

2009 Hyosung Aquila GV250 will not shift


Hi, Anonymous and the usual suspects are:
1. Clutch not disengaging.
2. Bent shift shaft.
3. Shift fork bent or seized.
4. Gear seized on the shaft.
5. Gear positioning lever binding.
6. Shift return springs weak or broken.
7. Shift return spring pin loose
8. Shift mechanism arm spring is broken.
9. Shift mechanism arm is broken.
10. Shift drum is broken.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://korider.com/index.php?topic=22261.0
http://www.motorcycleforum.com/59-motorcycle-repair/117196-hyosung-gv250-no-neutral.html
Hyosung Aquila 250 Service Manual
https://www.alpha-sports.com/Parts/H_GV250.htm
HYOSUNG GV250 User Manual

Dec 02, 2017 | 2009 Hyosung Aquila GV250

1 Answer

2009 Hyosung GT 250 R will not start when cold


Hi, Anonymous and the usual suspects are:
1. Choke not functioning properly.
2. The battery is not fully charged 12.5 volts or better.
3. Throttle not fully closed.
4. The intake manifold is loose or cracked and sucking air.
5. Air cleaner not sealed properly or missing element.
6. Air fuel mixture not adjusted properly.
7. Valves adjusted to tight.
8. Low compression top end needs a rebuild.
9. Engine oil to heavy for cold temperatures.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Hyosung Cold Start Problem
2010 Gt 250r takes forever to cold start
HYOSUNG GT 125 Manual
https://www.alpha-sports.com/Parts/H_GT250R.htm
HYOSUNG GT250 FI Owner Manual

Dec 25, 2017 | 2009 Hyosung GT 250 R

1 Answer

Hey I recently just replaced my gear lever for my 2005 hyosung gt250r and upon replacing I had troubles with shifting into neutral while the engine was running from 1st gear. I've tried shifting from


That is a common thing with the 250r, Just blip the throttle a little to get it to shift, or you could adjust your idle a little lower to help. don't set it lower than 950rpm tho.

Dec 10, 2011 | 2005 Hyosung GT 250

1 Answer

I own a 2008 Hyosung GT 650 and never had any issues until now. At first all I had to do was pull back on the clutch lever and start the motorcycle...no problem. Then I had to let off a little bit to get...


Hi, Paul_nason the ignition circuit cut-off system comprising of the side stand switch, clutch switch and neutral switch has the following functions:
a. It prevents starting when the transmission is in gear and the side stand is up, but the clutch lever is not pulled.
b. It prevents starting when the transmission is in gear and the clutch lever is pulled, but the side stand is still down.
c. It cuts the running engine when the transmission is in gear and the side stand is moved down.
Periodically check the operation of the ignition circuit cut-off system according to the following tests.
With the engine turned off:
1. Move the side stand down.
2. Make sure that the engine stop switch is set to "RUN"
3. Turn the key to "ON".
4. Shift the transmission into the neutral position.
5. Push the start switch if the engine does not start the neutral switch may be faulty.
With the engine still running:
6. Move the side stand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the side stand down if the engine does not stall you may have a faulty side stand switch.
After the engine has stalled:
10. Move the side stand up.
11. Keep the clutch lever pulled.
12. Push the start switch if the engine does not start you may have a faulty clutch switch.
This check is most reliable if performed with a warmed-up engine.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2008 GT650R Wont start
Troubleshooting Starting Cranking Problems on Hyosung Motorcycle
HYOSUNG GT 650 Service Manual
https://www.alpha-sports.com/Parts/H_GT650R.htm
HYOSUNG GT650 Owner Manual
HYOSUNG GT650 PARTS CATALOGUE Parts Catalog

May 02, 2017 | 2008 Hyosung GT650

1 Answer

I have Troy-Bilt storm 7524 snow blower which normally works fine, however, it has started to have problems shifting back into forward gear after being reversed. I'll put the snow-blower into reverse gear...


Try lubing the linkage where it shifts from forward and to reverse the linkage is most likely freezing up or has snow or ice build up causing it not to shift, My thought is your shoving it hard enough that it finally engages when you get the snow or ice to break off.

Jan 05, 2010 | Garden

2 Answers

My bike wont start


hiya mate! the bike is in neutral is it.. coz mine wont start if its in gear..when u sit on it pull cluch ,,neutral sould light up when u find it .. then start yr bike..

Jun 15, 2009 | 2005 Hyosung GT 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4898 Answers

yadayada
yadayada

Level 3 Expert

79865 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...