Question about 1993 Suzuki VS 1400 Intruder

1 Answer

Can i do this?.

I have a set of 2010 street glide front forks brand new . Can I put these on a 1993 Suzuki 1400 intruder .

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Suzuki Master
  • 1,554 Answers

Things to consider/ways to do this.

IF the fork tubes (the upper tubes that fit through the holes in the triple clamp) are the same diameter, then it's a simple swap-out.

If not, and you want to use the Harley triple clamp, then it's an issue as to IF the neck diameter AND length is the same.

Posted on Feb 10, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: changing front tyre of suzuki intruder 1400

just take the front wheel off and take it to a tire shop and they will usually put it on for like $5. if you dont want to do that you can use a few flathead screwdrivers and take off one side of the tire and then move the tire to the side you just took off and take off the second side. reverse to put new tire on

Posted on Oct 20, 2009

  • 83 Answers

SOURCE: How do you remove and install a new fork lock?

YOU WILL NEED TO REMOVE THE TRIPLE TREE FROM THE FRAME TO ACCESS THE LOCK. ONCE YOU GET THE STEERING SHAFT REMOVED FROM THE FRAME YOU WILL SEE HOW TO REMOVE IT.

Posted on Oct 20, 2009

  • 17 Answers

SOURCE: My suzuki intruder is missing backfiring on the

Did you sync the two carbs? If not the rear may be getting all the gas from the rear carb and none to the front. Twist throttle engine off and see if front carb cable is pulling the carb open.
Also unscrew the spark plug boot from the front spark plug wire and trim 1/8th inch off the wire and screw the boot back in. The plug wire end may be corroded on that wire.

Posted on Feb 08, 2010

  • 85 Answers

SOURCE: NEED TO PUT WATER IN RADIATOR SUZUKI INTRUDER 1400 '96

Your suzuki is air cooled with an oil cooler,it doesn't have a radiator...

Posted on May 28, 2010

  • 3 Answers

SOURCE: What brand tire is good to put on the front of my

i like the metzler 880 front and back.they are sticky and good for 12,000 miles

Posted on Sep 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1993 suzuki intruder 1400 isnt getting spark


your generator problly does not have a good seal. take the cover off clean the rust then reseal. Good luck

Apr 14, 2014 | 1993 Suzuki VS 1400 Intruder

1 Answer

Where's the flasher on a 1993 Suzuki Intruder VS 1400?


replace the indicater relay ! trace back the same colour wires !

Apr 04, 2014 | 1993 Suzuki VS 1400 Intruder

1 Answer

My 1999 suzuki intruder 1400 is vibrating while ridding over 30 mph, once i put clutch on or take it to neutral it stop s the vibration . when I am parked i accelerate the engine and the vibration s


Hi Eric, and the usual suspects are:
1. Wheels and/or tires worn or damaged.
2. Engine/transmission/vehicle not aligned properly.
3. Primary chain badly worn or links too tight as a result of insufficient lubrication or misalignment.
4. Engine to transmission mounting bolts loose.
5. Upper engine mounting bracket loose.
6. Ignition timing incorrect/poorly tuned engine.
7. Internal engine problem/flywheels shift.
8. Broken frame.
9. Stabilizer links worn or loose.
10. Rubber mounts loose or worn.
11. Rear fork pivot shaft nuts loose.
12. Front engine mounting bolts loose.
For more information about your issue, please visit the websites below, and for specific information or questions you can reach me at xlch@mail.com. Good luck and have nice a day.

http://www.jstilldesign.com/manual-book/gN/1999-suzuki-intruder-1400-service-manual.pdf

Mar 27, 2013 | 1999 Suzuki VS 1400 Intruder

1 Answer

What are the intake and exhaust valve specifications on the 1993 Suzuki VS 1400 Intruder?


try this site http://www.rockauto.com/catalog/raframecatalog.php?make=SUZUKI&year=1993&a=www.google.com.ph%2BSearch%2Bfor%2B1993%2BSUZUKI

Apr 28, 2011 | 1993 Suzuki VS 1400 Intruder

1 Answer

I need instrutions on puting fork seals in a intruder 1400 1996 modelI


it;s best to purchase a repair manual for your machine as it's a long time consuming process

Apr 04, 2010 | 1993 Suzuki VS 800 Intruder

1 Answer

Changing front tyre of suzuki intruder 1400


just take the front wheel off and take it to a tire shop and they will usually put it on for like $5. if you dont want to do that you can use a few flathead screwdrivers and take off one side of the tire and then move the tire to the side you just took off and take off the second side. reverse to put new tire on

May 31, 2009 | 1996 Suzuki VS 1400 Intruder

3 Answers

Too much shaking of my eyes/ helmet at high speed


Get yourself a Honda, Suzuki, Yamaha, Kawasaki. This will take care of the Harley shake, that is what Harleys do.

May 30, 2009 | 2008 Harley Davidson FLHX Street Glide

Not finding what you are looking for?
1993 Suzuki VS 1400 Intruder Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...