Question about 2005 Suzuki Boulevard M50

1 Answer

Wireing problem tale section blinker melted all the way to harness

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Suzuki Master
  • 9,098 Answers

A grounding wire, or loose connection.

Posted on Jun 15, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Having a major electrical problems. Cab blower, radio come on with key out of the ignition. Vehicle wont start when this happens. Acts like battery is dead. I try to jump start it and still nothing. I


There's definitely some wires that are shorted together, i would start at the radio if it had been changed out there would be a good source for a short. Also check your ignition switch, its a power distribution center that can go haywire when it starts shorting out. I would also look for wires going to the blower / radio that have been melted together allowing power to be transferred between them from an unwanted source ;ie non switched or direct. Wiring can be hairy, but if you can trace it down to a single source and repair and damaged wires you could save the hassle of replacing the wiring harness. Good luck

Dec 17, 2014 | 2004 Chevrolet TrailBlazer

1 Answer

Looking for a wiring diagram on the rear frame section of a f350 fx4 diesel with part filter,cat,and egt sensors


this repair would be best done with a new wiring harness. Un ensuring that the new harness is no where near the heat source.clip the connectors and replace the harness straight back in

Oct 08, 2014 | Cars & Trucks

1 Answer

My wiring harness going to my blinker switch is melted just wandering how much they cost or if they are even easy


best bet would be to find one in a salvage yard. get the harness pigtail off of the car and wire it onto your car. not hard to do just alot of cutting and crimping and taping of wires.be sure to check for high resistance on that circuit so you don't damage the replacement part.

May 19, 2012 | 1995 Dodge Neon

1 Answer

Tail lights, turn signal and hazard lights, dsh lights not working. when i change the fuse it blows


If the FUSE blows then it is confirmed that the circuit is SHORTED and so the heavy current drain make the fuse melt off.
So it is important that the circuit is traced to find the short. So remove the bulbs of the light circuits and check the holders, check the wiring harness, see for damage on the sections where the harness passes through. Now without the bulbs replace the fuse. If the fuse blows then the harness can be short to this circuit sections.

Jul 19, 2011 | 1999 GMC Sonoma

1 Answer

2000 oldsmobile silhouette electircal problems


you need to remove both rear tail lights and disconnect the plugs, look in the plugs and you will see 6 contacts look at the middle contact on either the top or bottom, the one the is connect to the black wire will probably be melted, you may be able to go to a junk yard and find one that does not have melted contacts and cut the harness about 4 inches before the plug and use splice connectors by matching the wire colors.

Dec 01, 2009 | 2000 Oldsmobile Silhouette

3 Answers

Rear lights wont go on but brake lights work


Fuse box is a good place to start, and check under hood for power distribution box with more fuses.

Jun 01, 2009 | 1991 Ford F150

1 Answer

Blinker showing up on right side when left side is signaled to come on on my 2004 Dodge Ram Hemi


either the multifunction switch is bad or the wiring harness for the blinker is worn threw in the steering column, take it to a shop before you burn up the wirng harness, even if it's fuesd it can still melt thewires and cost a ton of money to fix.

May 28, 2009 | 2004 Dodge Ram 1500

2 Answers

Pressing brake causing blinker issue


The trailer harness that was installed probably has a short inside the box that distributes power to the trailer pig-tail. Remove the trailer harness. You problem will be cured.

Jan 27, 2009 | 1999 Toyota 4Runner

Not finding what you are looking for?
2005 Suzuki Boulevard M50 Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...