Question about 2010 TVS Scooty Pep

1 Answer

Clutch Cover side Oil Leakage

Need Solution How To Control It

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 22 Answers

Replace the cover. Any patch will not last.

Posted on Feb 10, 2014

  • meyers335
    meyers335 Feb 10, 2014

    Replace the cover. Any patch will not last.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 3.0 ranger leaking oil at back of eng left hand side below valve covers . oil can be seen tracking down l side of eng thru wheel well


the oil pressure sender unit will be in that area so check that it has not failed or leaking from around the thread
another place of leakage is the rear edge of the rocker cover where the gasket has failed or not been fitted properly or loose screws for the cover

Jul 07, 2017 | Cars & Trucks

1 Answer

How do I check the transmission fluid on my 2007 hyundai elantra manual transmission


manual transmissions don't normally use flowing fluids for lubrication they use gear lubrication oil/grease these are heavy hi viscosity (maple syrup like) and don't flow like water like automatic trans do , ck'ing there level is a bit specific to what type of lube they use , a Hyundai uses Oil so there will be a pipe plug up on drivers side of trans near top (sorry no dipstick) un screwing this will allow one to use a Non metal object to stick in and see if oil is up to hole (reaching it) , of course obvious(wet look) signs of leakage (at drive shaft and clutch cover ) are a sure sign you have a leak and level is low , wet clutch covers aren't allways a sign of a leaking transmission but to one of a leaking clutch slave cylinder(common problem on Hyundai's) this is the device that moves clutch inside , ck oil level in clutch master cylinder to confirm this

Jul 29, 2015 | Hyundai Cars & Trucks

1 Answer

What would cause a transmission to malfunction?


Transmission can malfunction due to the following reasons:
- Before blaming the transmission, engine tune up be carried out to get the maximum performance and torque.
- Wrong type of transmission oil is used.
- Improper transmission fluid oil level.
- Contaminated transmission fluid.
- Transmission oil leakage.
- Throttle control cable adjustment. (Auto transmission)
- CVT oil calibration. (CVT).
- Clutch and pressure plate and clutch slippage. (Manual transmission).
- Drive shafts.
- Transmission damaged.

May 27, 2014 | Cars & Trucks

1 Answer

Oil leak seal cover primary


the easy one for that is to go to local auto shop and get a stop leak product other than that you you have to remove side cover and replace gasket be sure to drain oil first

Sep 07, 2013 | 2011 Bajaj Pulsar 220 F

1 Answer

Nissan pathfinder clutch problem


check dupper clutch master for leakage ,if no leakage then check d lower slave cylinder for leakage ,if dry then replace ur clutch plate and cover. also check ur gear oil if it is manual.

Jul 14, 2013 | Cars & Trucks

1 Answer

1998 kawasaki 1500 vulcan slave clutch bleeder valve


The clutch bleeder is behind the left engine cover, you will have to remove the left exhaust from the head and also the left front foot peg in order to get it off should be about 5 bolts holding engine cover on dont worry its just a cover no oil leakage from that side, then it will be down just above the frame, it will have clutch hose going to it.. to Bleed it remove cap on leftside handle bar make sure fluid level is 3/4 fulll hold clutch lever in then open valve, let air out then close valve release clutch lever, should fix if not repeat bleeding until you have good pressure on clutch lever, dont let fluild get to low . once pressure is good refill and put cap back on. put bike back togather and RIDE good luck

Sep 30, 2012 | 1996 kawasaki VN 1500 Vulcan Classic

1 Answer

Kia Sportage 2005. When hot and heavy clutch use such as a traffic jam or busy town traffic I am unable to slip into first, second and reverse When it cools all is well again! No signs of leakage or oil....


if its doing this when its hot then the clutch is either sticking on the spigot shaft ,of their is oil on the flywheel face which i doubt i suspect that spigot shaft is a bit dirty and rusty ,take the rubber boot cover off the clutch arm and with a long spouted oil can squirt some engine oil over the spigot shaft ,spray stuff is no good it dries out ,

Jan 29, 2011 | 2000 Kia Sportage

1 Answer

Hey just need to know how much oil the gearbox and engine holds on me crf450 08. just to clarify the gearbox oil goes on the kick starter side and the engine oil on the gear lever side. also should i warm...


there is clutch oil witch goes on the right side and then motor oil witch goes on the left side.. you should run honda oils in that bike hp4 for motor side and honda clutch oil for the clutch its in a tall red bottel..
about the levels, on the motor side(left) use the sight glass and put it half way. on the clutch side use the small screw thats on the clutch cover for a drain fill it till it starts to come out..but the easiest way to do this is to go by the service manuel specs.. you can call your local dealership to get them also

Mar 13, 2010 | RTO Honda Crf450 R Motorcycle Dirt Bike...

1 Answer

I have a lose clutch on a 2003 hyundai elantra would could this be. do i need to replace my whole clutch


no you don't need to replace hole clutch , there is oil leakage form any cylinder, arrest leakage or replace that it will solve your problem.thanks

Feb 25, 2010 | 2004 Hyundai Elantra

1 Answer

Clutch is grabing


sounds like clutch disks are in need of replacement. your clutch is slipping when under a heavy load. if you have adusted the cable properly, then i would focus on the clutch friction disks. these are designed to wear as they transfer power from the engine to the transmission.

drain the oil and remove the side cover to access the clutch basket. you'll need a new side cover gasket as well as a new clutch pack (friction & metal).

Jan 27, 2009 | 2005 Honda CR 125 R

Not finding what you are looking for?
2010 TVS Scooty Pep Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top TVS Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Milton Scott

Level 1 Expert

23 Answers

Are you a TVS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...