Question about 2004 Yamaha Royal Star Venture

1 Answer

Horn systematic negatively grounded? - 2004 Yamaha Royal Star Venture

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Yamaha Master
  • 41,728 Answers

Hi, Anonymous first check for continuity at the power and ground wire at the horn, then check for continuity at the horn button, back in the day there was a small adjustment ***** on the back of the horn, by turning it one way or the other you could set the limit on how much the diaphragm vibrated. For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have nice a day. The Venturers Yamaha Venture Technical Support Library
http://www.starbikeforums.com/forums/49-v-star/23937-horn-problem.html
http://www.yamahaventure.nl/pdf/servicemanualxvz13tf.pdf
OEM parts for Yamaha
http://www.yamahaventure.nl/pdf/ownersmanualxvz13tf.pdf

Posted on Apr 06, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Horn is out on a 2003 Mitsubishi Montero limited. What parts needed to fix it?


check horn relay works
get a 12v probe and test the horn switch works when pressed
12v should be supplied to the horn relay coil contact when the horn switch is pushed on.
Also check the fuse.
Check voltage going to horn when pressed
horn might be negatively switched so 12v positive is on one side of horn and relay switches ground negative .
You will find the horn relay under the bonnet in a relay compartment most likely

Dec 05, 2016 | 2003 Mitsubishi Montero Limited

1 Answer

Why are there two wires to the horn on a ford sapphire


it grounds when you hit button same with older dome lights

Mar 18, 2015 | Ford Cars & Trucks

2 Answers

Where is my steering column grounded. My horn does not work when ignition switch is on


Your horn should always work, key on or off. 1999 Accord uses a horn relay. Horns themselves going bad is not uncommon.

Aug 08, 2014 | 1999 Honda Accord

1 Answer

My horn WILL NOT work


Where are you connecting the tester to? If you are connecting one lead to the negative terminal on the battery and the other to the horn wire and it lights up try connecting a wire from the horn housing (bare metal) to the negative battery terminal and attach the horn wire to the horn and try it. if that works the ground path from the battery to the horn mounting place is broken somewhere. you may have to run a negative wire to the horn mounting place to make it work properly. Hope this helps.
Bob

Jul 18, 2014 | 1968 Mercury Cougar 4.9

2 Answers

Toyota Camry 1999 model horn does not work


new horn or relay gone most likely but make sure it is grounded good or wont work either hook battery booster cable from negative battery terminal to horn bracket if it works then clean mounting area under horn ground is bad

Dec 11, 2012 | 1998 Toyota Camry

1 Answer

My car horn only have 1pin but the new horn 2 pins how to make it work


the extra pin goes to ground. Cut the connector off the new horn, and connect it to the battery to determine which polarity sounds good. Then solder a terminal on the negative wire and make it long enough to reach a chassis ground point. Cut the connector off the old horn to use for your new horn's positive wire. OK?

Oct 31, 2010 | 1995 Nissan Maxima

1 Answer

No Horn


first look for your fuse panel, probably under dash, or under hood, then check horn fuse...this MIGHT work. If not locate your horn under the hood, probably in front of the radiator. if you have a volt ohm meter, just 10 dollars or so at home depot or radio shack, set it on ohms, put one lead on the negative of your battery, the other on one of the horn connections, if it shows zero (a continuity reading) that is the negative ground side of your horn then run one voltmeter lead directly from the negative battery terminal, to the negative horn connection, and have someone try the horn. If it works, great. if it doesnt take the other lead from the positive battery terminal, leaving the negaitve one in place, putting the other end of the positive on the other positive terminal of your horn. if it works, your horn is ok.

that probably means a blown fuse, or more trouble, a bad worn connection under your steering wheel, which means pulling the steering wheel and checking to see if the brass or bronze horn ring is making good contact with the steering wheel connection brass bump, or if it worn out. i had to go to dealer to get a replacement, was about $12 for a toyota, and they do wear out.

good luck

Mar 21, 2010 | 1998 Mercury Grand Marquis

1 Answer

Boat horn not working; fuse is good


TOOL NEEDED (1) DC test light or probe. TROUBLESHOOTING (1) generally a horn just has two wires positive and negative. Test negative by connecting dc test light negative to the negative on the back of the horn. use positive side of dc test light and touch a known positive connection. dc test light should light if not. find clean know ground for horn. Test positive by connecting neg side of dc test light to a know negative connection. use positive side of the dc test light and touch positive side of horn. test light should light up when you touch the horn switch. if dc test light does not light take a jumper wire and connect one side of jump wire to a known positive connection. take other side of jumper wire and lightly touch positive side of horn connection. horn should beep. if horn does not beep replace horn. if horn does beep test and or replace horn switch.

Sep 06, 2009 | Boating

1 Answer

1987 camaro horn not working - clicking noise at relay


Make sure the horn is grounded at the base of the horn where it is mounted.Also run a gound from negative battery post to the frame and body.Also check the horn by running a positive wire from battery to the horn,while making sure of a ground.If I can help lrt me know.

Apr 03, 2009 | 1987 Chevrolet Camaro

Not finding what you are looking for?
2004 Yamaha Royal Star Venture Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...