Question about Kymco Motorcycles

1 Answer

New carb but no start - Kymco Motorcycles

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 130 Answers

Which model is it ?

Posted on Feb 09, 2014


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 20 hp craftman wont start new starter got fire throu spark plug


Spray a little carb cleaner or brakeclean into carb w/air cleaner removed. If starts, check fuel supply to carb. If ok, clen carb and jet with spray carb cleaner and try again.

Jun 19, 2016 | Cars & Trucks

1 Answer

2006predator 90 won't start new carb new stater


New carb, starter, air filter, and new plug. The question is do you have spark, and did you empty old gas out of tank before you installed the new carb . You may have some water that went from tank into new carb. You won't start. GOOD LUCK FRIEND.

Sep 14, 2014 | Garden

2 Answers

I have a Ryobi RY28120 gas powered weedeater that will start sometimes and not at others. Not sure if the carb needs cleaning or if it need a new muffler. Maybe adjusting carb screws? Not sure! Also,...


Use only fresh gasoline (alcohol free if you can find it). Purchase a top quality synthetic 2 stroke oil such as Lucas, Golden Spectra and mix it exactly as the manufacture dictates. Install a new accurately gapped plug and make sure the plug wire cap (boot) is pulled back to inspect the wire to connector crimp. Start it up as you normally would to allow the new gas and oil to permiate the system and if you cannot get it to stay running without the choke being on shut it down and squirt some oil into the carburetor and pull the trimmer over, if this makes it start everytime it does not want to start and it allows you to click off of run you have either low compression (rings are worn). or your carb is yet another victim of the geniouses that thought alcohol in gas was a super idea. Either way you can replace the piston and rings or the carb. both are almost not worth the time and cost anymore, a new carb for mine is $70.00, with a new piston and ring set being around $40.00 and a brand new trimmer the same as this one on sale at $130.00 it was an easy decision to buy new.

Jul 18, 2014 | Ryobi Garden

1 Answer

Scooter wont start


Sounds dlumb, but first check and see that the fuel is flowing into the carb. You should make sure the ignition is working properly and firing, do this by pulling the plug wire from spark plug and hold it about a quarter inch from metal while turning the engine as if starting. A strong spark should jump the gap without a problem. If the spark is nice and blue, pull the spark plug and check to see if it got flooded out and is wet. If so, dry it out, clean it, regap it it, or install a new one. Then try starting it again after adjusting the new carb by turning the idle screw all the way in, then back it out one and a half turns for initial setting. If it still has problems spray starting fluid into the carb while turning it over. You should also check the new carb float level since not all new things work as they should.

May 25, 2014 | Health & Beauty

1 Answer

1999 Yamaha 1200GP Wave Runner wont' start. It has sat for about 2 years. I have new battery, new plugs and new gas, it turns over but won't start, any suggestions?


Sounds like the carbs are gummed up from the old gas sitting in them. Remove the carbs, disassemble, clean with a carb cleaner, and reassemble.

May 14, 2012 | Motorcycles

1 Answer

Craftsman Leaf blower with new carb won't start


check the head bolts to make sure they are tight

Dec 16, 2011 | Craftsman Garden

1 Answer

My hedge trimmer will not start... Put in new gas


It's not getting gas, due to being gummed up with old gas. Remove all of the old gas and mix up a batch of fresh gas&oil. Also get some carb cleaner. Put just a little of the gas&oil mix plus an equal part carb cleaner. Try to start it just to work the new mixture through the carb. You might use the spray start to help pull the new gas through. If it fires up on the new gas&oil&carbcleaner mix, shut it off and let it sit for an hour or two. Drain it out and try just a little gas&oiil without the carb cleaner. If all is well fill the tank. If not, repeat the whole process. If you can't clear the gum this way you may have to remove the carb to clean it. Good luck.

Oct 22, 2010 | Craftsman 22" Gas Hedge Trimmer

1 Answer

It will start, but will not stay started.


you more likly have a carb problem, you must flush the fuel sys out all tank lines and rr carborator install new seat and new fuel, MUST BE STABULIZED AT ALL TIMES! do not stabulize fuel older than 10 days. use a good carb cleaner spray to flush sys and carb than install new parts

Oct 10, 2009 | Mtd 22" Yard Machine Push Mower

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...