Question about 2007 Triumph Triumph Bonneville

Open Question

Air cleaner remove and replace how to - 2007 Triumph Triumph Bonneville

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble removing valve cover on the right side (passengers side) of the engine on a 1996 mark viii. Help


  1. Remove engine appearance cover retaining bolt and nuts.Remove engine appearance cover from vehicle.

  1. Disconnect engine control sensor wiring at intake air temperature sensor (IAT sensor) connector and crankcase ventilation tube from air cleaner outlet tube.
  2. Completely loosen air cleaner outlet tube to throttle body bolt (captured bolt).
  3. Loosen clamp on air cleaner outlet tube to engine air cleaner (ACL) and disconnect air cleaner outlet tube.
  4. Remove remaining bolt from support bracket clamp on RH valve cover to air cleaner outlet tube.
  5. Remove air cleaner outlet tube and engine intake air resonator.


  1. Remove two retaining nuts from engine air cleaner outlet tube bracket to valve cover and remove engine air cleaner outlet tube bracket.
  2. Remove four nuts retaining RH ignition wire cover and remove cover.
  3. Disconnect ignition wires from spark plugs with a gentle twist! pull motion on the spark plug boot. Remove spark plugs.
CAUTION: Do not pull on the ignition wire as it may separate from the connector in the boot.
  1. Remove bolts and studs retaining RH valve cover to cylinder head.
  2. Remove valve cover.

Sep 28, 2017 | Cars & Trucks

2 Answers

Location of the mass flow air sensor in a 2007 Cadillac SRX? how to replace?


Hard to believe you have a bad MAF in a 2007 caddy. How many miles on car? Have you tried cleaning the unit?

Parts store have a locator chart which should show location.

Apr 14, 2015 | 2007 Cadillac SRX

1 Answer

Replace air filter


Air Cleaner Element -- Explorer 4.0L and 5.0L



Removal
1. Release the air cleaner clamp and position the LH side of the engine air cleaner (ACL) (9600) and air cleaner outlet tube (9B659) out of the way.

2. CAUTION: Do not tamper with the sensing elements located in the mass air bypass of the mass airflow sensor.

Remove the air cleaner element from the RH side of the engine air cleaner.

Installation
1. Clean all inside surfaces ofengine air cleaner. Refer to «Cleaning and Inspection» in this section.

2. Install air cleaner element.

3. Position engine air cleaner halves together and close the air cleaner clamp.

Mar 07, 2011 | 1998 Ford Explorer

1 Answer

How to removing engine aif filter on 06 honda element ?


FOR A 2.4 LITER ENGINE
Air Cleaner Element Inspection/Replacement

8dc707a.gif
  1. Remove the air cleaner bolts (A) and the Air cleaner Housing cover (B).
  2. Remove the air cleaner element (C) from the Air cleaner Housing (D).
  3. Check the air cleaner element for damage or clogging. If there is damage or clogging, replace the air cleaner element. Do not use compressed air to clean the air cleaner element.
  4. Clean and remove any debris from inside the Air Cleaner housing.
  5. Install the parts in the reverse order of removal.
  6. Good luck

Oct 20, 2010 | 2006 Honda Element

1 Answer

1988 Chevrolet Berreta, 6 cylinder. I can't find the Air Filter to it.


from autozone.com
  1. Remove either the wing nut, upper cover retaining bolts or release clips from the upper top of the air cleaner and either lift off or separate the upper air cleaner housing or lid.

0aee193.gif


Fig. Fig. 1: Remove the air cleaner housing lid using a screwdriver ...
8788df2.jpg

Fig. Fig. 2: ... then lift the housing lid up and remove the air cleaner element

  1. Remove the air cleaner element and replace it with a new one.

6406f6f.gif


Fig. Fig. 3: Exploded view of the air cleaner assembly - 2.2L engine shown

  1. Wipe the air cleaner housing out using a damp cloth. Check the lid gasket, if equipped, to ensure that it has a tight seal.

To install:
  1. Position the new element in the air cleaner housing.
  2. Position the lid or housing cover, then tighten the retaining bolts/nut or fasten the clips.

Sep 29, 2010 | 1988 Chevrolet Beretta

1 Answer

Where is the air filter and how to replace it?


Six cylinder:
The air cleaner element is inside the air cleaner housing on the left side of the engine compartment. (It has a large hose connected to it).

To replace it: Disconnect the hose from the air cleaner housing cover with flat-tipped screwdriver.

Loosen the four bolts, and remove the air cleaner housing cover.

Remove the old air cleaner element.

Carefully clean the inside of the air cleaner housing with a damp rag.

Place the new air cleaner element in the air cleaner housing.

Reinstall the air cleaner housing cover, and tighten the four bolts.

Connect the hose to the air cleaner housing cover with a flat-tipped screwdriver.

Hope this helps you.

Jan 08, 2010 | 2004 Honda Accord

1 Answer

How to replace engine air filter in 2001 honda odyssey


The air cleaner element is inside the air cleaner housing on the driver's side of the engine compartment.
To replace it:
1. Remove the two pins holding the air intake cover by pulling the head on each pin. Remove the air intake cover.
2. Loosen the four bolts by using a Phillips-head screwdriver.
3. Disconnect the clip from the bolt on the air cleaner housing, then remove the air cleaner housing cover.
4. Remove the old air cleaner element.
5. Carefully clean the inside of the air cleaner housing with a damp rag
(The coolant lines inside the air cleaner housing may be warm. Do not open the hot air valve when cleaning the inside of the air cleaner housing)
6. Place the new air cleaner element in the air cleaner housing.
7. Reinstall the air cleaner housing cover. Reinstall the clip on the bolt; make sure the clip is under the washer. Tighten the four bolts.
8. Reinstall the air intake cover. Reinstall the two pins and secure them by pushing on the heads until they lock.

Hope this helps you through the process.

Nov 23, 2009 | 2001 Honda Odyssey

1 Answer

How to replace engine air filter


  1. Disconnect negative battery cable.
  2. Disconnect inlet air temperature sensor electrical connector.
  3. Disconnect fresh air makeup hose from throttle body air inlet hose.
  4. Disconnect PCV hose from intake manifold.
  5. Loosen hose clamp at throttle body air inlet hose. Remove hose from throttle body
  6. Push in on locking tabs to disengage air inlet hose from air cleaner housing. Remove throttle body air inlet hose and air cleaner element together.
  7. Separate air cleaner element from throttle body air inlet hose.
INSTALLATION reverse

Jun 11, 2009 | 2002 Chrysler Sebring

2 Answers

Were is the IAT in a 2004 nissan altima


Removal and Installation To Remove:
  1. Remove or disconnect the following:
    • Mass air flow sensor electrical connector
    • Tube clamp at the electronic throttle control actuator
    • Air cleaner to electronic throttle control actuator tube, upper air cleaner case
    • Mass air flow sensor from the cleaner case.
To Install:
  1. Install or connect the following:
    • Mass air flow sensor to the cleaner case
    • Air cleaner to electronic throttle control actuator tube
    • Tube clamp at the electronic throttle control actuator
    • Mass air flow sensor electrical connector
prev.gif next.gif

Mar 28, 2009 | 2004 Nissan Altima

2 Answers

How to change air filter and intake hose ?


Hi have a nice day!

Components
3625b8c.gif Disassembly

1. Remove the air duct connected to the air cleaner.
2. Disconnect the intake air temperature sensor harness.
3. Remove the air intake hose from the air cleaner side.
4. Remove the air cleaner cover and filter.
5. Remove the air cleaner mounting bolts and remove the air cleaner.


INSPECTION


1. Check the air cleaner body, cover, or packing for distortion, corrosion or damage.
2. Check the air duct for damage.
3. Check the resonator for distortion or damage. 1a53eea.gif 4. Check the air cleaner element for restriction, contamination or damage. If the element is slightly restricted, remove dust and other contaminants by blowing air from the upper side through the element. 5. Check the air cleaner housing for restrictions, contamination or damage. ca8fd93.gif INSTALLATION Installation of the air cleaner is the reverse order of removal

May 31, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
2007 Triumph Triumph Bonneville Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...