Question about 1997 Honda CBR 600 F(3)V

1 Answer

Engine won't stay running

4 cylinder motorbike engine won't stay running. It is a multi point fuel injected engine, instead of the original carb. The sparks are all working. It will start running sometimes and only keep going with near full throttle which will hold engine at less than tick over until it eventually stops.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 408 Answers

Sound like fuel supply fail.Check the fuel pump, fuel filter and fuel pump relay first.

Posted on Jun 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It was running and it made a backfire and since then it cranks but won't turn over and start what could be the problem


Does it have spark , is there fuel get to injectors ? What engine 2.2L 4 cylinder or 2.8 V-6 ? TBI - throttle body injection or Multi port fuel injection ? Does it have timing belt or timing chain etc... Open the oil fill cap on the valve cover , have some one crank over the engine . Look inside the oil fill hole , can you the rocker arms moving ? Timing belt broke or jumped time >

Jan 01, 2016 | 1987 Chevrolet Cavalier 4 Door

1 Answer

What do you do if you cant get your 1992 ford f250 to start?


Start with the basics. To run, the engine needs fuel, air, ignition spark, and compression. So one should verify the fuel pump is working and fuel is getting to the engine. When you first turn the key to on, the pump should come on for a brief second or two to prime the lines with fuel. If you don't hear it come on, spray inside the intake with starting fluid or carb cleaner and see if engine tries to start. Does it at least fire and try to run? If so, the pump needs testing to see if it is bad or wiring to the pump is the problem. If the pump is working, the next thing is to check for spark on a spark plug wire when the engine is cranking. You can buy an inexpensive spark tester at a parts store, or just pull a spark plug wire off the plug and hold the metal wire terminal end 1/4 inch from a metal piece on the engine. Use a glove or heavy rag to hold the wire and have someone crank the engine over. To verify ignition is good, you need to see a strong blue spark consistently when the engine is cranked over. If no spark, the ignition system is the problem, and further testing of the system is required. Best done by a well-equipped shop. If pump is working and you have spark, but still won't start, either check fuel pressure with a pressure gauge (correct fuel pressure is very important!), or check that injector circuit is working and injectors are spraying fuel into the intake or into the cylinders, depending if you have multi-port injection, or throttle body injection (or central point fuel injection, I think Ford calls it).
Plenty of other things to check, but sudden no-start problems are usually because of fuel or ignition failure. If you haven't changed the gas filter or air filter in some time, that is a good place to start.

Feb 24, 2013 | Cars & Trucks

1 Answer

I have a Toro 4 cycle gas trimmer that won't stay running. Starts, then sputters, then dies. I've changed the oil, drained fuel & put in new fuel.


check to make sure the air filter and the fuel screen are clean, the screen is the little white plastic piece on the end of the hose in the tank. if it is still sputtering try cleaning the bell out on the carb. it is the little metal cylinder on the bottom of the carb where it holds the fuel until it evaporates into the engine if it gets clogged the engine will not run properly.

Jun 30, 2011 | Garden

1 Answer

Does the 1991 saturn have individual fuel injectors


if you look along the intake manifold where its mounted to the engine there should be 4 individual sensor looking components(one for each cylinder) with a 2 wire connector fastened to them,then you have multi-point injection(one injector for each cylinder).if not then you have what is called throttle body injection which is one body with 1or2 injectors that supply fuel to all the cylinders.this looks similar to a small carburetor located in the center area of the intake manifold were all the intake runners come together.

Jun 13, 2011 | 1991 Saturn SL1

3 Answers

How do I know if my truck has a carb or if it's fuel injection?


FUEL INJECTION THROTTLE BODY INJECTION SYSTEM HAS TWO ROUND FUEL INJECTORS ON TOP.CARBURETOR DONT HAVE FUEL INJECTORS.IT HAS CHOKE VALVE AND FUEL NOZZLE WHICH IS THE FUEL METERING SYSTEM.

Feb 04, 2011 | 1987 Nissan Pickup

1 Answer

1991 buick park ave. missing at highway speed, tach revs up to 3000 rpm instead of usual 2200 sometimes dies at take off and then runs like normal for a while


It seems that correct amount of fuel is not being supplied to the engine. Most probably the fuel nozzles have accumulated some dirt. Try spraying some carb cleaner into the air intake assembly when the engine is idling. This ought to mix with the air-fuel mixture being injected into the cylinders and if the nozzles are narrowed, should clean them up.

Nov 11, 2010 | 1991 Buick Park Avenue

1 Answer

Still starving for fuel after replacement of fuel line and filter.Getting gas to carb but will not stay running?


1990. this should be throttle body injection, you didnt post engine size. Need to check fuel pressure at idle and under load, While driving under hard acceleration. On a carb fuel pressure should be between 4-6.5 psi at all times. TBI should be 9-13 psi. Also on the carbs there is a filter on the carb at the fuel inlet. Need a 1" wrench to remove the line and remove the internal filter.

Sep 11, 2010 | 1990 GMC Sierra

1 Answer

4 cylinder motorbike engine won't stay running. Fuel is injected in. The sparks are all working. It will start running sometimes and only keep going with near full throttle which will hold engine at less...


If its cable throtle then clean throtle hosing on the inlet manifold.If that does not work clean the injectors.By adding fuel treatment for injection systems.Or remove and get them checked out.

Jun 03, 2009 | 1999 Plymouth Voyager

2 Answers

Too much fuel pumped into the carb. What to do?...adjust?...set?


The idle air control valve may be at fault, also the throttle position sensor may be telling the engine th wrong information and sending too much fuel, a couple other ideas come to mind but I not an expert. A faulty injector is one of them.....I another idea that may help as well: Vacuum Leak: The ECM will try to compensate for leaks up to a certain size. This will cause the ECM to compensate and possible send too much fuel to the engine...???? Good Luck

Mar 15, 2009 | 1986 Pontiac Fiero

Not finding what you are looking for?
1997 Honda CBR 600 F(3)V Logo

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...