Torque specification please give me the torque specification for cylinder head 5AFE L touring.

Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 DegreesI would check in the service manual as well, just to be sure.

I apologize, but I don't have access to specific torque specifications for every engine and vehicle. The torque specifications for the cylinder head bolts on a Kia 2.7L J2 engine may vary depending on the specific model and year of the vehicle. It is crucial to refer to the manufacturer's service manual or consult with a certified Kia mechanic to obtain the correct and up-to-date torque specifications for your particular engine.
The service manual will provide the recommended torque values, as well as the specific sequence for tightening the cylinder head bolts. Following the manufacturer's specifications is important to ensure proper sealing and avoid any damage to the engine components.

It is all here complete with pictures and diagrams. A Service Manual of your own is a great investment as stated by our Pro Tech Larry Ng.

https://www.google.com/search?q=2008+chrysler+300+touring+3.5+V6+head+camshaft+bolt+torque+specs

..

Details here on Page 94

11. Following the tightening sequence shown in
Figure 15, torque the fasteners in 1/2 turn increments and in two stages to the specifications.
Torque the fasteners to 1/2 the given torque, then
torque them to their final specifications:
a. Cylinder head nuts (1-4, Figure 15): 50 N•m
(37 ft.-lb.).
b. Cylinder head cap nut (5, Figure 15): 35 N•m
(26 ft.-lb.).
c. Cylinder head bolts (6 and 7, Figure 15): 20
N•m (15 ft.-lb.).
12. If the cylinder has also been reinstalled, torque
the cylinder bolts (A and B, Figure 23) to 10 N•m
(89 in.-lb.). One of the bolts sits in a recess (B, Fig-
ure 23) in the cylinder block.
13. If removed, install the locating pin (B, Figure
21) into the camshaft

Engine Lower End Torque Specifications - V star 1100

https://www.manualslib.com > ... > Owner's manual
Yamaha V star 1100 Manual Online: Engine Lower End Torque Specifications. Item N•m Alternator cover bolts 10 Connecting rod nuts 48 Crankcase stud 10 mm 20 ...

• 
  

  Cylinder Head Removal - Yamaha V star 1100 Owner's Manual

  https://www.manualslib.com > ... > Owner's manual
  Yamaha V star 1100 Manual Online: Cylinder Head Removal. The procedures for removing the rear (Figure 3) and front (Figure 4) cylinder heads are nearly ...
  
  
  videos that might help
  
  https://www.google.com/search?q=2003+v+Star+1100+head+bolts+torque
  
  ..

Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

Toyota 4A/ 5A-FE Cylinder Head Torque:
(a) Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts.
(b) Install the plate washer to each cylinder head bolt.
(c) Install and uniformly tighten the ten cylinder head bolts in several passes in the sequence.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)
HINT: Cylinder head bolts are in length of 90 mm
(3.54 in.) and 108 mm (4.25 in.). Install the 90 mm
(3.54 in.) bolts (A) in intake manifold side positions.
Install the 108 mm (4.25 in.) bolts (B) in exhaust
manifold side positions.

Tighten the cylinder head bolts. Tighten the cylinder head bolts is sequence to 29 Nm (3.0 kgf-m, 22 ft. lbs.). Use a beam-type torque wrench. When using a preset type torque wrench, be sure to tighten slowly and do not overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt and retighten it. Make sure the threads are clean, new heads bolts are best.

should come with the package containing the head gaskit or upper cylinder kit.Mostly at the back or printed inside the package.

Please don't forget to rate. Thank you:

Left side front cylinder head



Cylinder head bolt torque sequence—3.4L engine

Cylinder head by aligning it with the dowel pins

New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.

Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).

Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).

Right side rear cylinder head:



Cylinder head bolt torque sequence—3.4L engine

New cylinder head gasket

Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins

New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.

Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).

Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).

Spark plug wires

Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).

Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.

Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).

Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).