Question about 1982 Yamaha XJ 650

1 Answer

Bike won't start. Only hitting on 2 cylendars

Bike won't start. Only hitting on 2 cylendars Push start button, nothing. As letting off get some spark. Have replaced 2 pick up coils but not sure if wired right. Need wire diaghram. Won't fire if cold, will fire from push button if warm, any thoughts?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 353 Answers

Posible vacuum leak replace vac line to fuel tank

Posted on Jun 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Turns over but indignation button won't fire


possibly you have water in the electrical, let it dry and retry.

Jun 06, 2013 | Triumph Motorcycles

1 Answer

2003 Goldwing won't start...just one click when start button pushed


you may have blown the starter solenoid or even worst the starter motor
i cannot diagnose without seeing the bike properly
i strongly suggest you put in a workshop and get it diagnosed properly

Apr 12, 2013 | 2003 Honda GL 1800 Gold Wing

1 Answer

Timing chain


bent push rods could have been caused when the chain broke and not from the chain been replaced wrong or the timing out.

if the engine was running when the chain broke the cam would have stopped leaving all the valves in the same positon as the mometum of the fly wheel continued to turn the pistons in the cylendars could hav come up and hitting the valves and bending the push rods. and or damaging the cylendar head.

recommend removing the head and have it checked for damage, as well as replacing the bent push rods, and cylendar gaskit. once the head is checked and the valves are seated well. then replace and follow instructions in the set up for the pistons and cam prior to replacing the chain and setting the timing.

I hope this was helpful.

Oct 20, 2012 | 1991 GMC C3500

1 Answer

Buell blast won't start


You have a bad switch somewhere - either the clutch switch in the clutch lever or the kickstand switch is bad. Of course I had a blast that had a sloppy connector at the back of the key switch that did all of the above too.

Apr 03, 2012 | 2001 Buell Blast

1 Answer

The bike won't start. When you push the dtart button the head light shuts off and nothing else happens


sounds to me as though your battery is very low on power, either that or your starter motor is stuck and wont turn which will pull loads of amps from battery and possibly dim headlight to nothing.

Sep 07, 2011 | 1996 Honda VT 600 C Shadow

1 Answer

My bike won't start(lights light ,horn works push starter button nothing no power to spark plugs ??? i belive one of the starter interlocks must be stuck in an open position possibly?


Hey, When that happened to me I took the bike half apart and it ended up being the Kill switch. Try rocking it back and forth also if you have contact cleaner flood the switch and let it dry then give it a light spray of wd-40. also check the start switch to be sure it is making contact,bike is in Neutral and the kick stand switch is also working.

Jul 07, 2011 | 2000 Honda Valkyrie Interstate

1 Answer

Hi!!!!! i have an kawasaki zx6r 1998 and it dosent want to start , i started it 2 days ago, but today it dosent want i charged battery, and when i push start button it dosent do nothing, i checked coil...


Check the clutch, neutral and side stand safety interlocks.
Double check that the bike is in neutral, and the clutch is pulled in when trying to start the bike.
If the bike is in gear with the side stand down, the bike cuts off all ignition.
If the clutch isn't pulled in, the starter won't engage.
Check all these safety interlock switches, and make sure you are in neutral with the clutch in when trying to start the bike.

Jun 27, 2011 | kawasaki ZX-6R Motorcycles

Not finding what you are looking for?
1982 Yamaha XJ 650 Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...