Question about 2005 Suzuki Boulevard C90

1 Answer

My signal lights and 4-way flashers don't work.

I have checked the fuse and its fine is there a flasher (like in a car0.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 88 Answers

There is a selection of fuses at the rear of the bike close to the drive shaft end.
Standing facing the side of the bike with the clutch lever.....
Open the rear most lower section of the bodywork.
In here you will find the indicator fuses.

The flasher relay might be in there.

Hope this helps.

Posted on Nov 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 dodge 3500 and the brake lights and flashers don't work but turn signals do work


work on one thing at a time, brake lights first, check the brake switch, is it mounted ok ? is power geting to it ? replace if any doubt. check all fuses, replace 4-way flasher, cheap fix . a repair manual has good info, including wire diagrams, for all circuits, etc.,,.. check wir harness @ rear of truck, & along frame for damage, corrosion, etc.,.

Jan 29, 2013 | Dodge Ram 3500 Cars & Trucks

1 Answer

TURN SIGNALS & FLASHERS DON'T WORK


First check for a blowin fuse for them. If the fuse is good ,You need to change the signal light flasher.

Oct 25, 2012 | 1995 Plymouth Neon

1 Answer

Rear hazard flashers don't work 1994 Chevrolet Cavalier


Hazard flasher power comes from the 20A S/LP fuse in the fuse block. It is applied to the hazard flasher in the convenience center. Flasher output is applied to the turn/hazard/headlight SWITCH assembly where activation of the HAZARD switch causes flashing power to be applied to the turn indicators and the turn filaments of the front and rear dual park/turn lights. If replacing the fuse doesn't work, trace the power through the circuit. Check for misssing/disconnected ground wires.

Sep 16, 2012 | Chevrolet Vehicle Parts & Accessories

1 Answer

How to fix turn signal on 86 Chevy Astro Van


you don`t say but do the lights work either on the front/back on both sides.if not then it may be a fuse that needs replacing or need a bulb replacement.if the lights work but don`t flash then it sounds like a signal flasher problem.the flasher is located in the fuse panel under the dash on the drivers side.if the hazard flashers work then turn them on to find the hazard flasher by the fuse panel then you will know what the signal flasher looks like and change the signal flasher.make sure you change the one for the signals and not the hazard one.if the hazards work then i would say the signal switch is good as the hazards work through the same switch.

Apr 21, 2011 | Chevrolet Astro Cars & Trucks

1 Answer

Why my emergency flashers work and my signal lights don't


the hazard lights use a different flasher(relay)then the signal lights.you don`t say if the signals work on one side or not,you should check the fuses for the signal lights in the fuse panel under the dash on the drivers side.if you put the hazards on and find the flasher then you will know what the signal flasher will look like,it is on the fuse panel and replace they should work.

Mar 18, 2011 | 2000 Buick LeSabre

1 Answer

Turn signal dosent work


you need to check to see which bulbs don`t work both front and back lights for the signal on the side it`s not working,you don`t say if any signals work or not if no signals work then you need to check the fuses under the dash on the driver`s side.now if it`s just one side then check the lights as mentioned above.if one isn`t then replace the bulb.if neither bulb is working then it sounds like the signal flasher is not working.turn on the hazard flashers and check the lights front and back.if all bulbs work then leave the hazards on and look under the dash for the flasher that is making the noise,this will show what the signal flasher will look like,then find the signal flasher on the fuse panel under the dash it should be located on the fuse panel.and replace

Mar 15, 2011 | 1997 Dodge Ram 1500 Club Cab

1 Answer

1997 Chevy Tahoe both turn signals stopped working


Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Jul 21, 2009 | 2001 Chevrolet Tahoe

3 Answers

Turning signal and 4-way hazard flasher not working


the actual hazard lights switch is also a relay and linked to signals left/right try checking this out ?

Aug 30, 2008 | 2000 Toyota Sienna

Not finding what you are looking for?
2005 Suzuki Boulevard C90 Logo

Related Topics:

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...