Question about 1990 kawasaki ZXR 750

1 Answer

Kawasaki Mule 3010, keeps getting flat battery, wont jump start

Hi, The company i work for has a 3010 Kawasaki Mule. The other week it had a flat battery, checked it for charging and found would charge to 13.9v, so i fitted a new battery as didnt want to take the risk of just charging (old battery). 2 weeks it had gone flat again, completely stopped mid drive. Suspected fuel pump so fitted new with filter and plugs. Had difficulty jump starting as starter motor was locking up due to overheat. Eventually started, drove around for 10 mins, all good. Stopped and started perfectly. Went for another quick drive 5min and it just conked out and couldn't start due to flat battery. It wasnt charging at idle but would go to 13.9v with some throttle. Any suggestions? Could you please email me at pkzbates@optusnet.com.au

Posted by on

  • Anonymous Mar 25, 2014

    I have a kawasaki mule gas 3010 that will not charge the battery, where do i start looking and what type of chargeing system is this

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

Sometimes when the battery keeps going dead like that, a component may be creating a current draw. you can do a simple current draw test with a fluke meter by setting the meter to read amps, make sure the test leads are in the proper portals on the fluke for an amp test, and disconnect one of the battery cables and connect the test leads in-line with the battery and cable. It would help to know you have a good fuse inside the fluke. They are easy to blow, and whatever you do, DO NOT try to start the unit with the meter hooked up for the amp draw test. That is how fuses are blown. With the key off, check for any amp draw. If there is, you can start unplugging components until the draw goes away. If there was no draw to begin with, you may have a stator coil (or alternantor, whichever it has) that is weak and can't keep up.

Posted on Jun 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mule 550, It starts fine, but will not shut off when the key is turned off....any suggestions?


Hey Matt, sounds like the switch is going bad.. I would see if it will start - WITH THE KEY OFF by "jumping" the solenoid.. if the switch is bad.. it might start... and confirm the switch is bad..

Jun 21, 2017 | kawasaki 2008 Mule 3010 4x4

1 Answer

I have a 2003 kawasaki mule model 3000 it wont say running at idle what to do


Full tune up and carb clean .get new plug,air filter.oil Chang ,carb clean and adjustment.that should do it.,., try fuel filters and test fuel pump see if it's functioning properly.,.

Dec 10, 2016 | kawasaki 2005 Mule 3010 4x4

1 Answer

Where is the neutral safety switch for a kawaski 3010 mule


Kawasaki Mule Update - YouTube

? 2:16
www.youtube.com/watch?v=Fw_jeQUU6Hw
Jan 25, 2013 - Uploaded by Penguinboy1995
solenoid is reading battery voltage and the constant hot, it is not sending the 12 volts from the switch to the ...

Sep 19, 2015 | kawasaki 2005 Mule 3010 Trans 4x4

1 Answer

Primary clutch bolt for a 2005 Kawasaki 3010 mule 4 x 4 will not screw back in


Hi ! for an informantion, please visit the website below. If you need more information about a specific electrical issue you can reach me at motor@motorpartstore.com.
http://www.motorpartstore.com.Good luck and have a nice day.

Apr 12, 2015 | kawasaki 2005 Mule 3010 4x4

2 Answers

#1cylinder not firing on 2003 3010 Kawasaki mule


if its firing ok on other cylinders, unlikely to be pump or fuel filter, focus on electrics, plug, ht lead etc

Dec 08, 2013 | 2003-2007 Kawasaki Kaf620 Mule 3010 4x4...

1 Answer

#1 cylinder not firing


its probably your coil, the igniter would make all cylinders go out

Dec 08, 2013 | 2003-2007 Kawasaki Kaf620 Mule 3010 4x4...

1 Answer

Kawasaki mule 3010


Check the starter or solenoid.

Apr 27, 2013 | kawasaki 2008 Mule 3010 Trans 4x4

Not finding what you are looking for?
1990 kawasaki ZXR 750 Logo

1,873 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...