Question about 2001 Honda NSR 125 R

1 Answer

Rear swing arm on nsr 125

Where can i get the tool that removes the locking nut from the swing arm

Posted by on

  • Anonymous Mar 26, 2014

    dont know if i have to remove swing arm or not

  • Anonymous Mar 30, 2014

    removel of swing arm

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

You will be able to purchase one from a honda dealership, honda motor cycle dealer. if they dont have one in stock they should be able to order you one from the honda factory.

Posted on May 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove swing arm on a 99 yamaha big bear 350


Easy - take off tires, then caps over axle/castle nuts if you have them.
- take cotter pins and axle nuts off both ends of axle. Right side - remove brake drum, then remove two brake shoes, simple Springs connect them, you can pull apart intact, remove any collars, washers off the axle behind brakes, then there might be 4 bolts and a plate - the other side you can see the bearing. Now - this is important - for. The side with the brakes, take a socket bigger than the threads but size of axle lip - and you place that deep socket (side with brakes!) over the threads (threads will be inside deep socket) lip of socket touches lip of axle about 2-3 inches down - hit that w a hammer and the axle will go out to the left if facing rear of four wheeler. Next - remove brake lines and breather hose for rear end.
There are bolts that attach the rear end to the swing arm (to the right) take them out and maybe the bottom guard for rear end. Then where the rear end attaches to drive shaft tube portion of swing arm there are four bolts - when all that is done you'll be able to remove rear end. Undo top bolt or you might get away w/bottom for shock - next two pivot shaft nuts - big socket like, Allen head in middle - remove nut from pivot shaft (left and right side where swing arm pivots) then takeallAllen head and unscrew two thick bolts that the pivot shaft nuts tighten to our - there's a collar and bearing in there where the bike's swing arms pivot at. I've done it a dozen times - if you have any problems or that wasn't too clear, message me, I'll dig up some tech sheets from a service manual I got on a bike that year - close to same model - same mechanics, Yamaha was pretty universal. I got a 98 & 99 Yamaha 2wd and a 96 Yamaha 3504wd. All pretty easy to work on. I have a swing arm I might get rid of from Florida and a decent rate if yours is done for and you gotta replace. I sell and buy off eBay to keep most of my toys on the trail.Good luck

Nov 20, 2014 | Motorcycles

1 Answer

How do you take the rear swing arm off of a 1982 harley davidson


using a bike jack or milk crate on somethig comparable to set your bike on so that your rear wheel is in position to remove it . take off your chain/belt. remove brake caliper ancers axel rear wheel diconnect shocks chain guars bla..bla..bla.. bend lock tabs on lock washer back remove nut on the swing arm bolt drive bolt out. buy case of beer to drink while your old lady cleans parts easy as 123

Sep 24, 2013 | Harley Davidson Motorcycles

1 Answer

How do you take the swing arm off of a 1982 harley davidson


Raise rear tire off ground. Loosen chain adjusters, loosen and remove axle nut and remove axle. Remove chain from rear sprocket. Remove bolt from lower shock mounts. Loosen nut on swing arm and remove swing arm bolt.

Sep 24, 2013 | Harley Davidson Motorcycles

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

How do i get the back tire off my 1982 vf 750 sabre??


put bike on support stand or jack up rear wheel. remove small plastic cover on the left side swing arm and remove nut that anchors brake drum housing to the swing arm support. remove the rear brake linkage from the rear drum. remove the axle nut and slide out axle shaft from axle housing. Be careful to notice the position of the spacer and washers. the installation is the same as removal. be sure to re-adjust the rear brake linkage. If adjusted properly prior to removal it might help to mark the position of the nut on the linkage before removing.

Mar 30, 2010 | 1982 Honda VF 750 S

1 Answer

Loose chain


First off, there is a sticker on the swing arm on how much tension it should have. It's 30 mm up and down play on the chain in the middle between the sprockets.
You need a 1 1/4 socket for the rear axle.
You need a 10mm and 12mm wrench.
Loosen the rear axle nut, but don't remove.
Loosen both 12mm nuts.
Back out both 10mm bolts untill your chain tension is close to 30mm.
Tighten the 12mm nuts and then the axle nut.
Note...Make sure by the markings that both sides are even, so the wheel is straight, and make sure the wheel is pushed forward as you tighten the axle nut.

Nov 24, 2009 | 2003 Honda CR 125 R

1 Answer

Removal of swing arm


remove seat and fuel tank/ air filter box assembly.
get the bike off the ground and secure so it wont fallover.
remove rear wheel, release the rear brake hose ,
undo clamps holding shock tank,
remove upper shock mounting bolt,
remove bolt holding double connecting rod to chassis,
remove ring nut and fork pin adjuster,
remove pin,
remove shock double connecting rod from chassis,
undo wishbone shaped brackets both sides , from centre attachment..
swing arm should be free..

Oct 17, 2009 | 2002 Aprilia RS 125

1 Answer

How do I tighten my belt on a 05 rd king


Pull the clip out of the rear axle lock nut, loosen it, the at the rear of a the swing arm there are 2 adjusters, one on each side. Loosen the lock nut and turn the screw until the belt gets tight. Make sure you turn each side EVENLY, or you will **** the wheel to the right or left. Tighten up the lock nuts and torque the big axle nut to about 55-65 foot/lbs, replace clip. But seriously, I would let a dealer do this. The rear belt is supposed to have a certain amount of deflection with 10 lbs pressure applied to it. The dealer will have the proper tool to check this.

Jul 08, 2009 | 2004 Harley Davidson FLHRCI Road King...

1 Answer

Need to remove swinging arm from bike to replace bearings. how do you remove studs from engine?


Hi, Richsuelaw sorry you can't find the first and best tool you ever bought for your Derbi despair, not for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
CAN GET MY SWING ARM SPINDLE TO UNDO
https://yamahaclub.com/forums/topic/31793-how-to-remove-swing-arm-bearings
Derbi GP1 125 250 Workshop Manual
https://www.oemmotorparts.com/oem2.asp?M=Derbi
http://www.derbi.com/fr/images/stories/modelos/37/manual.pdf

Jun 20, 2009 | 2006 Derbi Senda R 125 4T

1 Answer

I need to tighten the chain on my derbi cross city 125


looks like you have a nut at the rear of thr swing arm, one on each side, these are the rear wheel/chain adjusters. slacken the wheel nut and then adjust the nuts, there should be some kind of markings on the swingarm so you can get both sides the same. when done tighten the wheel nut and you are done

Mar 25, 2009 | 2008 Derbi Cross city

Not finding what you are looking for?
2001 Honda NSR 125 R Logo

Related Topics:

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...