Question about 1997 Honda CBR 900 RR Fireblade

1 Answer

HONDA FIREBLADE RRV. REVS FLUCTUATE

WHEN TRYING TO MAINTANE A STEADY SPEED IE 40-50-60 THE BIKE TENDS TO HUNT. BUT WHEN GOING THROUGH THE GEARS IT SEEMS OK. THE LAST OWNER PUT A DYNO KIT ON IT, COULD IT BE THE CARBS NEED SETTING UP. ALSO WHEN STARTING THE BIKE FOR THE FIRST TIME EACH DAY IT NEEDS FULL CHOKE FOR ABOUT 3 MINUTES. THANKS

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 408 Answers

Dyno kit supplies you extra carb needles which are useless in street use.They are only for racing use.If the previous owner installed them then you should put the stock ones back.Also reset your carbs (vacuum pressure, mixture screws)

Posted on May 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My rrt fireblade missfires when headlights are on at low revs


Check the ground for regulator or another ground that is common with lights and fuel pump if is there any.

May 05, 2015 | 1996 Honda CBR 900 RR Fireblade

1 Answer

Struggeling so switch gears on high revs


You could have either have the clutch not adjusted correctly or you could have glazing on the clutch discs or both. I would check for glazing on the clutch pack.If they seem glazed rub them on the cement a few times. The concrete will not harm anything but it will clear the glazing off of the clutch pack.

Dec 27, 2013 | Honda XR 200 Motorcycles

1 Answer

1989 gl1500 engine speed fluxuates while running at a steady speed. most noticeable in lower gears,seems to run smooth in high gear.Also,engine speed will fluxuate while idleing or trying to hold the...


This is a common problem related to plugged or very dirty low speed idle jets in the carb, When they get that bad it is best to have the carbs cleaned by a reliable mechanic.

May 18, 2011 | 1989 Honda GL 1500 Gold Wing

1 Answer

Hi i have a cb1300 on 04 plate bought recently . in low gears and approx 2000 to 3500 revs the bike seams very snatchy and surging on steady throttle but change up a few gears and its fine . its not like a...


Check your clutch plates, it may be slipping at higher RPM on low gearing but have enough contact area on lower RPm higher gearings. Good enough to rate this advise?

Sep 01, 2010 | 2004 Honda CB 1300

1 Answer

I wanna make ma bike more faster


The easiest cheapest way to get more power to the rear wheel of a chain drive motorcycle is to install a smaller counter shaft sprocket than the one that is on the bike right now. Usually one tooth less than what is on the bike right now will do. Example: 15 to 14 or 13 to 12 The top speed of your bike may drop from 130 mph to 120 mph but most people don't get to use that anyway. This simple mod may allow you to raise the front wheel in higher gears.

Aug 28, 2010 | 1997 Honda CBR 900 RR Fireblade

1 Answer

Rpm's jumping


Might have a bad IAC motor

Jan 11, 2010 | 2002 Dodge Durango

1 Answer

I need to find the tourqe settings for the swing arm spindle for a Honda CBR 900 RRV. Thanks


The book specified torque for the swing arm spindle nut is 87 foot pounds.

Nov 27, 2009 | 1996 Honda CBR 900 RR Fireblade

2 Answers

My cbr 954rr fireblade has a problem I'm not sure what it is but this is what it is doing. I can start the bike and it will turn over about 3 to 6 times and fire right up fast. and I can rev it high. I can...


check your petcock vacuum line. it may be pinched or all dried up and cracked. sometime when you pull the tank off you put a kink in lines and reduce the flow of fuel just enough to simulate it running out of gas.

Oct 11, 2009 | 2002 Honda CBR 954 RR Fireblade

Not finding what you are looking for?

Open Questions:

See all 1997 Honda CBR 900 RR Fireblade Questions

1997 Honda CBR 900 RR Fireblade Logo

269 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...