Question about 1995 kawasaki GPZ 1100

1 Answer

How to take back wheel off 95 1000 kawasaki gpz

Need to replace valve stem flat tire

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 126 Answers

If you only need to replace the valve stem, you can get a removal tool and sparestems at an autmotive parts store. If you need to take off rear tire, the steps should be obvious. Loosen chain tensioner but before you do this use a marker or some other marks to show original location, which eases re-installation.

Posted on Aug 23, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How do I remove a valve stem from riding mower rim?

If your simply replacing it with a new one or installing an inner tube you take a sharp knife and cut back side off. Don't cut completely as you want to catch that piece before it falls inside the tire. Then you simple pull the stem breaking that piece off, catching the back piece as it falls.

If you wanting to put back in a new stem for tubeless use you need a t-shape valve core wrench. After you place the new stem in the hole you thread the tool on and pull the new stem into place.

Jun 22, 2014 | Craftsman 42 in. Deck 19.5hp Lawn Tractor

1 Answer

2004 kawasaki 110cc took apart back tire area and have a thick metal cylinder shaped object and forgot where it goes

hi there hicks32

that metal object is a rim loc , it should have a rubber top bonded on it , this fits into another hole other than the one that the tube valve stem goes into

you should have 2 holes ,fit rim tape, fit one side of the tyre bead, instal rim lock ( with rim tape running over the rubber on the rim loc ) fit the washer and nut losely on the rim loc bolt stem by at least 4 or 5 threads fit the tube as you normally would, push the rim loc stem fully up ( so that the nut rests on rim )do not let the rim loc stem receede into tyre ) refit the other tyre bead and inflate the tyre and seat the beads on the rim , tighten the rim loc nut and the valve stem nut
make sure that that both rim loc and valve stem are straight when inflated and tightened

refit your wheel

cheers pauly46

Jun 08, 2011 | kawasaki Motorcycles

1 Answer

Struggling to fit replacement inner tube and tyre to our quinny buzz3... Any tips?

You need a set of tire levers to begin with.. anyplace that sells bike parts/tubes tires will have these.. they are just a nicely set of angled thin yet dull levers.

Using the levers you will need to lift one edge of the tire off the rim so the tire is half way on the wheel. To simply replace the tube.. continue on to B.

To completely remove the tire off the wheel.. flip the wheel over and using the levers pry the tire the rest of the way off the wheel. working your way around.. it will be snug then suddenly free.

Replaceing the tire is the same..except you only want to put it on half way before inserting the tube..

B. Remove the air stem cap and if you have the tool to remove the needle valve from the stem.. do that too as to let ALL the air out of the flat.. then pull the bad tube out.

Put the new deflated tube inside the wheel as flat and wrinkle free as possible starting with placing the air stem through the wheel.. and working it around until well seated.. some folks will use a bit of talcum powder on the tube.. usually they come dusted to allow them to properly fit when inflated.

Once you have the tube in the wheel.. start pressing the tire bead back under the rim.. depending on the wheel.. you may want to partly inflate the tube.. just a tiny bit.. so it will not get trapped between the tire and wheel rim when you re-seat the tire.. you can usually re-seat the tire to the rim with your fingers..becareful not to pinch yourself.

Inspect the wheel to make sure no parts of the inner tube is visible.. inflate to proper psi.. put on the stem cap.. replace the wheel.

You can buy a set of tire liners that will prevent punctures.. but of course this involves doing most of the above times four.

Lastly.. if you feel you just can't get it done.. stop by a good bike shop.. they will do it for you in just a few minutes.. possibly for no charge or little charge.

Best of luck!

Apr 11, 2011 | Toys

1 Answer

The fron tire of my Craftsman GT500 tractor is flat. how can I change it?

Hi, W/D here.
Find out why it went flat first. Air the tire up, and apply soapy water to the tire, then look for bubbles. If the tire went flat due to a puncture, you can repair it in place; Wal-Mart, and hardware stores market an inexpensive kit for repairing tubeless tires. Basically, you run a reamer into the puncture site, then fit the hole with a plug. Quick and easy. The repairs last.
If the tire is leaking around the valve stem, you can replace that in place as well. Same places sell valve stems. You deflate the tire, and install the valve stem from the inside.
If it is leaking around the rim, you can remove the valve core, and put a product called "Slime" in it to help seal it off.
If you really want to remove the tire, they are attached usually by one of two ways: 1. Bolt-on. There will be bolts in the rim of the tire. Removing these will allow the wheel to be removed, or 2. The wheel will be fitted to the axle with a bolt in the axle. Remove the center hub of the wheel, remove the cotter pin, remove the nut, then the wheel will come off.
If the repairs can be made with the wheel on, it's easier.
Best regards, --W/D--

Feb 12, 2011 | Garden

1 Answer

Need help reseting for tire size 26x2.1 changed to road tires can't find my book it's a sigma bc 906

you can measure your wheel by placing your bike on a flat surface with the valve stem on the wheel in the bottom most position or 6 o clock position. mark the floor where the valve stem is. now roll the bike forward so that the wheels gets one full revolution and the valve stem comes back to the 6 o clock position and mark the floor at the valve stem. now get a tape measure and measure the distance between your two marks. Convert this measurement to usually centimeters. that will be the number that put into your computer.

the manual can be downloaded here


Bicycle Parts and Accessories

Jul 03, 2009 | Sigma Bc 906 Computer

1 Answer

Fix a front flat tire on a mongoose varial bike

The first step is to remove the wheel assembly from the bike. Once that is done insure all the air is removed from the tube by holding in the needle on the valve stem. You may have to remove the cap from your valve stem first. Next, using a flat blunt tool, pry the inside lip of the tire away from the rim and hold down the tool. Make sure you don't have the tube pinched with your tool. Next, using a second tool, repeat the first step about 6" from the first tool. This should start the tire to come off the rim on the side you are working on. You should now be able to pull out the tube and inspect for holes. Use a simple tire patch kit if you can or simply replace the tube.

To replace the tube, remove the valve stem cap and insert it from the tire side through the hole in the rim for access. Replace cap on stem to help hold valve in place. Carefully lay tube inside tire without folding it. You may have to bunch it up a bit. Start pushing tire edge back around the edge of the rim. When you get almost to the end it will get tough to if the tire is tight.Use your blunt tool to help it over the edge of the rim. Once the tire is on, make sure the valve stem is pulled up tight and straight before refilling with air. Inspect the tire to make sure it is seated on the rim all the way around on both sides. If not, release air from tube and make adjustments and refill. Replace wheel on bike and enjoy your day!

Big Daddy

Apr 11, 2009 | Cycling

2 Answers

Tires mounted on Chrysler Chrome Rime go flat when cold

it is most likely the valve stems. take off the caps and spray some soapy water in them and around the base. if there is a leak you will see bubbles.

Jan 14, 2009 | 1999 Chrysler 300M

1 Answer

Jeep LIberty 2006 valve stem broke off

Just go to a tire store. They can resolve your problem quickly. A valve stem is a common item.

Dec 08, 2008 | 2006 Jeep Liberty

Not finding what you are looking for?
1995 kawasaki GPZ 1100 Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

77186 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides