Question about Suzuki GSX 600 F (Katana Motorcycles

Open Question

Front sprocket torque - GSX 600 F (Katana Suzuki Motorcycles

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: torque setting

The sprocket nut torque setting is 132Nm. If you are after the plastic cover torque settings, i dont think they have one. Hope this helps.

Posted on May 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the front sprocket torque


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Front and Rear sprocket torque specs
http://super-tenere.net/forum/xtz750-drive/6011-front-sprocket-torque
http://www.yamaha-tdm.cz/download/5PS1_AE1.pdf
OEM parts for Yamaha
YAMAHA TDM900 Owner Manual

Aug 02, 2014 | Yamaha TDM 900 Motorcycles

1 Answer

Kawasaki torque specs


Axle nut 145 Nm
rear sprocket nuts B and C models 74 Nm
rear sprocket but E and F models 59Nm
front sprocket nut 125 Nm
front caliper mounting bolts 34Nm
Hope this helps - if your wrench isn't in Nm you can get a conversion online.

Jun 23, 2014 | 2000 kawasaki ZX-9 R Ninja

1 Answer

Rear sprocket torque setting ducati m750


Hi, Anonymous sorry you can't find the first and best tool you ever bought for your Ducati despair not for a mere $0 you can download another one. For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have a nice day.
rear sprocket nuts torque spec
Torque for front and rear sprocket nut bolt Ducati 1299 Forum
Free Ducati Motorcycle Service Manuals for download
Ducati Maintenance
Ducati OEM Parts Fiche Lookup and Online Ordering

May 22, 2012 | Ducati Monster 750 - Dark - City - Dark...

1 Answer

Fzs 1000 front sprocket nut torque


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Need torque for front sprocket nut
Front sprocket Nut Torque in Fazer 1000 FZ1 corner Forum
Yamaha FZS1000 2001 Service Manual
OEM parts for Yamaha
YAMAHA FZS1000 Owner Manual

Apr 06, 2012 | 2005 Yamaha FZS 1000 Fazer

1 Answer

TORQUE Set 4 front sprocket 02 yamaha R6


Hi, Allen for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.r6messagenet.com/forums/r6-maintenance-technical/547-front-sprocket-nut-rear-sprocket-nuts-torque-specs.html
http://www.r6-forum.com/forums/57-garage-mechanical-help/68148-sprocket-torque-specs.html
1999 2002 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Dec 21, 2011 | 2002 Yamaha YZF-R6

1 Answer

FRONT SPROCKET TORQUE SETTINGS FOR A FAZER 1000 04 YEAR


Hi, Ollie316 for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Need torque for front sprocket nut
Front and Rear sprocket torque specs
Yamaha FZS1000 2001 Service Manual
OEM parts for Yamaha
YAMAHA FZS1000 Owner Manual

May 10, 2011 | Yamaha FZS 1000 Fazer Motorcycles

1 Answer

How to set the timing on 1998 GMC Sierra 5.7


5.0L and 5.7L Engines To Remove:
  1. Remove the crankshaft balancer.
  2. Drain the cooling system.
  3. Remove the water pump.
  4. Drain the engine oil.
  5. Remove all engine oil pan fasteners except two nuts at rear of engine.
  6. Separate the engine oil pan from the front cover.
  7. Disconnect the crankshaft position (CKP) sensor wire. gm-03-50-845.gif

  8. Remove engine front cover. gm-03-50-849.gif

  9. Pry the oil seal from the front cover.
  10. Inspect the front cover seal area and crankshaft balancer seal area for damage. gm-03-50-846.gif

  11. Rotate the crankshaft until the timing marks on the crankshaft and the camshaft sprockets are aligned.
  12. Remove the crankshaft position sensor reluctor ring. gm-03-50-847.gif

    NOTE: Free play on the slack side of the camshaft timing chain must measure less than 0.43 inch (11Mm) or timing chain and sprockets must be replaced.
  13. Remove the camshaft sprocket bolts.
  14. Remove the camshaft sprocket.
  15. Remove the camshaft timing chain. NOTE: Do not turn the crankshaft assembly after the timing chain has been removed in order to prevent damage to the piston assemblies or the valves.
    gm-03-50-848.gif

  16. Remove the crankshaft sprocket using J 5825-A.
  17. Remove the crankshaft balancer woodruff keys (if required).
To Install:
gm-03-50-850.gif

  1. Install the crankshaft balancer woodruff keys into the crankshaft.
  2. Align the crankshaft sprocket keyway with the crankshaft balancer woodruff key. WARNING
    Wear eye protection when installing crankshaft sprocket.
    gm-03-50-851.gif

  3. Use J 5590 to install crankshaft sprocket.
  4. Install the camshaft sprocket and camshaft timing chain. 9308kg61.gif

  5. Ensure that the crankshaft sprocket alignment mark is in the 12 o'clock position and the camshaft sprocket alignment mark is at the 6 o'clock position.
  6. Install the camshaft sprocket bolts and tighten the camshaft sprocket bolts;
    • Torque to: 18 ft. lbs. (25 Nm)
  7. Install the crankshaft position sensor reluctor ring until completely seated against crankshaft sprocket. NOTE: The composite type engine front cover and seal must not be reused. Always install a new engine cover with a new seal.
  8. Install new engine front cover and bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  9. Clean sealer from corners of oil pan gasket where it meets the engine front cover. gm-03-50-775.gif

  10. Apply a 0.196 in (5 mm) bead of adhesive, GM P/N 12346141 or equivalent, 1.0 in (25 mm) long to the engine front cover to engine block junction.
  11. Install oil pan bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  12. Tighten oil pan nuts.
    • Torque bolts to: 18 ft. lbs. (25 Nm)
  13. Connect the crankshaft position sensor wire.
  14. Install the water pump.
  15. Install the crankshaft balancer.
  16. Fill the engine to the proper level with oil.
  17. Fill the engine to the proper level with coolant.
  18. Test drive the vehicle to confirm the repairs.

Nov 05, 2010 | GMC K1500 Cars & Trucks

2 Answers

Does my 2001 saturn sl 1.9l have a timing belt or chain?


It is a chain and its not the easiest but it could be worse.It is as follows:
1.9L SOHC Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Right front wheel and splash shield
    NOTE: Place a 1 in. x 1 in. x 2 in. long block of wood between the torque strut and cradle to ease removal and installation of the torque engine mount.
    • 3 right side upper engine torque axis to front cover nuts and the 2 mount to midrail bracket nuts, allowing the powertrain to rest on the block of wood
    • Drive belt, tensioner and pulley
    • Power steering pump attaching bolts and set the pump to the side with the lines still attached
    • A/C compressor from the bracket and set aside with the lines attached
    • Camshaft cover
    • Using a strap wrench or a piece of wood wedged between the damper spoke and the lower side of the engine front cover, hold the damper and remove the bolt. With a suitable 3-jaw puller and the slots cast into the damper, pull the crankshaft damper/pulley assembly from the crankshaft.
    • Install the special oil seal replacement tool SA9104E, to be sure the front crankshaft timing sprocket is held firmly in place and prevent guide damage. Install with the flat side towards the crankshaft sprocket.
    • Remove or disconnect the following:
      • Front 4 oil pan bolts and cut the seal away from the front cover
      • Front cover bolts and carefully pry the cover away from the cylinder block at the pry location tabs, which are provided. Remove the cover from under the hood or through the wheel well
      • Front cover oil seal from the cover
      NOTE: During timing chain and sprocket removal, position the crankshaft 90 degrees past Top Dead Center (TDC), to be sure the pistons will not contact the valves upon assembly.
    • Carefully rotate the crankshaft clockwise so the timing mark on the crankshaft sprocket and keyway align with the main bearing cap split line (90 degrees past TDC).
    • Remove or disconnect the following:
      • Timing guides and tensioner
      • Camshaft sprocket bolt, using a 7⁄8 in. (21mm) wrench to hold the camshaft. Then, remove the timing chain and camshaft sprocket
      • Crankshaft sprocket
      To install:
    • Inspect the chain for wear and damage. Check the inside diameter of the chain, it should be no more than 16.77 in. (426mm). Inspect the chain guides for wear or cracks and the timing sprockets for teeth or key wear. Replace components as necessary.
    • Verify that the crankshaft keyway is positioned 90 degrees clockwise past TDC (keyway at 3 o'clock). The keyway should align with the split between the bearing cap and engine block.
    • Bring the camshaft up to No. 1 TDC by loosely installing the sprocket and rotating the sprocket until the timing pin can be inserted. The camshaft contains wrench flats to assist in turning the shaft. The dowel pin should be at 12 o'clock when the camshaft is at TDC.
    • Install the crankshaft sprocket, then rotate the crankshaft counterclockwise 90 degrees up to No. 1 TDC (keyway at 12 o'clock).
    • Position the chain under the crankshaft sprocket and over the camshaft sprocket. The timing chain should be positioned so that 1 silver link plate aligns with the reference mark on the camshaft sprocket and the other aligns with the downward tooth (at the 6 o'clock position) on the crankshaft sprocket. The letters FRT on the camshaft sprocket must face forward, away from the cylinder head and excess chain slack should be located on the tensioner side of the block.
    • Install or connect the following:
      • Timing pin to verify proper alignment of the camshaft and sprocket. Torque the sprocket bolt to 75 ft. lbs. (102 Nm).
      NOTE: Do not allow the camshaft retaining bolt to torque against the timing pin or cylinder head damage will result.
      • Timing chain guides with the words FRONT facing out. Install the fixed guide first and verify the chain is snug against the guide, then install the pivot guide. Torque the bolts to 19 ft. lbs. (26 Nm) and verify that the pivot guide moves freely
      • Retract the tensioner plunger and pin the ratchet lever using a 1⁄8 in. No. 31 drill bit inserted in the alignment hole at the bottom front of the component
      • Tensioner. Torque the bolts to 14 ft. lbs. (19 Nm), then remove the drill bit
    • Make one final check to verify all components are properly timed, then remove all timing pins.
    • Install or connect the following:
      • Seat a new front cover oil seal using the installation tool with a press
      • If the engine front cover casting or assembly is replaced, the 3 torque axis mount studs should also be replaced. Torque the new studs to 19 ft. lbs. (25 Nm).
1.9L (DOHC) Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. drain the engine oil.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Right front wheel and splash shield
    NOTE: Place a 1 x 1 x 2 in. (25 x 25 x 51mm) block of wood between the torque strut and cradle to ease removal and installation of the torque engine mount.
    • 3 right side upper engine torque axis to front cover nuts and the 2 mount to midrail bracket nuts, allowing the powertrain to rest on the block of wood
    • Drive belt, tensioner and pulley
    • Power steering pump attaching bolts and set the pump to the side with the lines still attached
    • A/C compressor from the bracket and set it to the side with the lines attached
    • Camshaft cover
  4. Using a strap wrench or a piece of wood wedged between the damper spoke and the lower side of the engine front cover, hold the damper and remove the bolt. With a suitable 3-jaw puller and the slots cast into the damper, pull the crankshaft damper/pulley assembly from the crankshaft.
  5. Install the special oil seal replacement tool SA9104E or equivalent, to be sure the front crankshaft timing sprocket is held firmly in place and prevent guide damage. Install with the flat side towards the crankshaft sprocket.
  6. Remove or disconnect the following:
    • Front 4 oil pan bolts and cut the seal away from the front cover
    • Front cover bolts and carefully pry the cover away from the cylinder block at the pry location tabs, which are provided. Remove the cover from under the hood or through the wheel well
    • Front cover oil seal from the cover
    NOTE: During timing chain and sprocket removal, position the crankshaft 90 degrees past top Dead Center (TDC), to be sure the pistons will not contact the valves upon assembly.
  7. Carefully rotate the crankshaft clockwise so the timing mark on the crankshaft sprocket and keyway align with the main bearing cap split line (90 degrees past TDC).
    • Timing guides and tensioner
    • Camshaft sprocket bolt, using a 7⁄8 in. (21mm) wrench to hold the camshaft. Then, remove the timing chain and camshaft sprocket
    • Crankshaft sprocket

Nov 30, 2009 | 2001 Saturn SL

1 Answer

How much torque do i need for monster 696 front sprocket?


don't understand the question?

1 tooth down in the front is almost equal to 3 teeth up in the rear

smaller front or larger rear sprocket will give more torque and vice versa.

Sep 19, 2009 | 2008 Ducati Monster 696

1 Answer

Torque setting


The sprocket nut torque setting is 132Nm. If you are after the plastic cover torque settings, i dont think they have one. Hope this helps.

Mar 28, 2009 | 2007 Triumph Tiger

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...