Question about Motorcycles

Open Question

Head bolt torque spec, 1956 fordson major diesel

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 254 Answers

SOURCE: Need torque wrench settings for cylinder head bolts

try here http://www.manualz.info/

hope this helps

Posted on Jan 04, 2009

Ad
bunnydawg
  • 5158 Answers

SOURCE: 91 kx 250 torque values

Engine Top End:
Auto Decompressor Bolt 104 in·lb
Cylinder Head Cover Bolts 87 in·lb
Cylinder Head Bolts: M10 36 S
M6 104 in·lb S

the S in that means the specified pattern ... just like tightening car tire bolts... please note all that it its INCH lbs....

don't know why it says just 36 for the M10 bolts unless they left out inch lbs

Anything else let me know as i've got a manual for the 250 f... actually i've got a few different ones

Robert

Please take a moment to rate this solution as i've taken a few minutes to find the manual thanks

Posted on Jan 28, 2009

chuck943
  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

  • 3567 Answers

SOURCE: torque specs for cam on 2006 honda crf250r

Rock the caps around to make sure the bearing locating clips are lined up. Torque the bearing caps to 12 foot-pounds. At this point you must check the valve clearances again. If any are off, the cam must be removed and the correct shims installed.

Please rate this solution. Thanks!

Posted on Apr 07, 2009

  • 3567 Answers

SOURCE: need torque specs for 98 yz 250,rebuilding engine

Go to the site below and you can download a free srevice manual for your bike.

http://www.carlsalter.com/motorcycle-manuals.asp

Top rating due on this answer!

Posted on Apr 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a small fluid drip from the back of my 1956 fordson major (at pto shaft ) is this a big job? & could it cause leak between gearbox & back axle.


If it is a small leak just leave it alone it is not worth the work and most likely the shaft is worn and the real cause of the leak.

Jun 25, 2017 | Cars & Trucks

1 Answer

Can only get gears in fordson major diesel when pulling up hydraulic leaver. 1956


Sounds like an adjustment is needed to the lever settings.

Jun 14, 2017 | Cars & Trucks

1 Answer

What are the torque specs for head bolts on a 2003 Ford Windstar Van?


When doing such major work, there are other parts that need correct torque and sequence as well. Buy a cheap shop manual from an auto parts store for this info and so much more.

Oct 03, 2016 | 2003 Ford Windstar

1 Answer

What is the head bolt torque for


Not having a manual or knowing the bolt thread size ..I would be guessing...can't guess!!!
Being a diesel the torque will have be very close to factory spec's.. no more that 10% above factory spec...I do not have a manual.. google the specs..sorry

Mar 06, 2016 | kawasaki 2007 Mule 3010 Trans 4x4 Diesel

1 Answer

Toyota 2c. I need cylinder head and flywheel Torque settings


Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

Aug 06, 2014 | Cars & Trucks

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

What is the torque spec for the head bolts on a 1993 dodge ram 50 w/ 2.3 l


Click here to see how to torque the head bolts on your 2.3 diesel engine.

Jan 18, 2013 | Dodge Cars & Trucks

1 Answer

1956 fordson major diesel-has front end loader and backhoe on back. What weight hydraulic fluid should I use in the loader and backhoe systems.


It depends a little on what the temperature is outside. I think I normally run a 10w in my backhoe.

Feb 02, 2012 | Cars & Trucks

2 Answers

Head Bolt torque settings for a 3.1 bighorn turbo Deisel


What is the torque for the crank pulley for 3.1turbo

Dec 21, 2010 | 1996 Isuzu Trooper

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...