Question about Harley Davidson Motorcycles

2 Answers

ABS light stays on 2008 street glide after putting on a 21 inch DNA

Put on a 21 inch DNA wheel and the ABS light stays on

Posted by Anonymous on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 20 answers of more than 400 characters.


    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

You might have damaged the sensor which is pretty easy when changing wheels, rather flimsy design, so check wire connection to sensor.

Posted on May 14, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Harley Davidson Master
  • 40,786 Answers

Check for broken wire to the sensor rotor at each wheel
check that the inner part of the rim has not worn through the wiring to the sensor.

Posted on May 14, 2015

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 2006 Harley Street Glide turn signal problems

hi, if you have not yet fixed the problem , the fuse box is located underneath the left sidecover in front of the left sattlebag youll need to remove the bag to get the side cover off ck the fuses thats all it should be ,prolly what happened was a bulb went bad and shorted the circut blowing the fuse for them theyre on the same fuse as the tach and speedo

Posted on Apr 27, 2009

  • 150 Answers

SOURCE: I need the torque specifications for the rear

Your wheel is 95 to 110 ft lbs

Brake Disk is 30-45 ft lbs ( lock tight)

Pulley i( belt Sprocket) is 55-65 FT Lbs Lock tight red on both.

Posted on Jun 15, 2009

  • 13 Answers

SOURCE: My check engine light goes on sometimes and then

on your dash is the button to check your milage. push it in and hold it down until your codes come up. some of the numbers it will go through will only be ecm numbers

Posted on Oct 09, 2009

Testimonial: "exactly what I needed. Thanks,"

  • 4565 Answers

SOURCE: where is the oil drain

I'm not really familiar with the Street Glide but usually on the "Glide" models, the oil tank is on the bottom of the transmission. There are usually two drain plugs on the bottom of the pan. The drain closest to the left front corner is the engine oil drain. The one nearest the center is the transmission.

Good Luck

Posted on Aug 03, 2010

  • 4565 Answers

SOURCE: 2006 Harley Davidson street glide brake light

Try loosening the bolts holding the front master cylinder on the handlebars. Slide the master cylinder down as close as possible to the right handlebar switch housing. If this doesn't work, the front brake light switch is probably bad and needs to be replaced in the right switch housing.

Good luck

Posted on Sep 25, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2012 Road Glide Ultra. 16k miles. w Thunder max ECM. Throwing code U1040. What is it and what is the solution?

U1040 = Loss of ABS serial data

Does the "CHECK ENGINE" light stay on?
If not, then it's a "HISTORIC" code (not current).

Clear the code and see if it comes back, as it might have just been a glitch.

Oct 16, 2013 | 2008 Harley Davidson FLHX Street Glide

1 Answer

2007 road king police abs light stays on

with most ABS light stay means a problem.

most of the time the wheel speed sensor.

2 wire connection to pick up coil (transducer)

what is located near the axle hub.

may be not getting signal from open circuit

or transducer to far away from ring

Jul 29, 2009 | 2008 Harley Davidson FLHX Street Glide

1 Answer

Front fender mounting

We use 3/8" feul line min. thickness. 2 pieces taped to wheel.

Feb 05, 2009 | 2008 Harley Davidson FLHX Street Glide

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers


Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides