Question about Harley Davidson FXD Dyna Super Glide Motorcycles

1 Answer

Noise when clutch is fully disengaged - FXD Dyna Super Glide Harley Davidson Motorcycles

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Harley Davidson Master
  • 1,554 Answers

If it's a rattle sound, most likely the clutch plates rattling until they clamp up with the pressure plate when you release the clutch lever.

Posted on Jan 02, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ginocussen
  • 216 Answers

SOURCE: clutch not fully disengaging

You have either air in your hydraulics which you need to bleed or else the clutch plates are worn/warped....here is the repair manual....
rate me if I've helped you. Thanks.
http://www.carlsalter.com/download.asp?fileid=075084077095049050053045050048048046040083088046077067088046069067088041095050048048049046112100102

Posted on Apr 04, 2009

  • 86 Answers

SOURCE: my dirtbike only moves when the clutch is fully dinengaged...

is there any free play with the clutch lever? only need about a quarter inch of free play.. if there is none, it will burn out the clutch plates.

Posted on May 18, 2009

  • 95 Answers

SOURCE: clutch is slipping, does not fully disengage. can

sounds like to me you may need a new cable, hopefully you did not run the bike very long, if so may need a new clutch also

Posted on Jun 16, 2010

Testimonial: "Thanks, I will replace the cable and see what ahppens"

  • 12 Answers

SOURCE: how do i adjust a clutch on a 2004 ttr-125

look at clutch diagram,is it u fix or put it on the correct sistem?mostly wrong part is added or not added make this prob..

Posted on Jul 31, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car will not engauge into 1st or 2nd gear


the gear grinding noise is because the clutch plate is not fully disengaging and the input shaft is still driving. If you did not use the same length of push rod then the slave cylinder is not moving enough to disengage the clutch. Check it out that with the pedal on the floor the piston in the slave cylinder should be almost to the edge of the slave cylinder . That is where It should be to be working properly

Jan 13, 2014 | 2004 Pontiac Grand Am

1 Answer

1994 ford escourt clutch will not disengage fully, tried bleeding the hydralic clutch but still not disengaging fully. Any sugestions


could be slave cylinder or clutch master cylinder. might also be the throw out bearing binding up on the shaft not allowing full movement.

May 31, 2012 | 1994 Ford Escort

1 Answer

I have a 94 saturn sc2 that seem like the clutch is not fully disengaging. Is there any reason for this other than the clutch no good?


depending on whether the clutch is cable or hydraulic, the issue could be in the linkage (if cable), and you may have to adjust the cable so that when the pedal is on the floor the clutch is fully disengaged..if hydraulic, try bleeding the clutch cylinder. if that doesn't solve the problem, then you may have a leak in the line leading to the clutch

good luck with your fix!

Mar 03, 2011 | 1994 Saturn Sc

2 Answers

There are few problems mentioned below: 1. In morning when engine is cold, it produces too much noise, when pressing clutch and it increases, when lifting the pedal (Half Clutch), when engine is hot, this...


from the description , the noise is a failing throw out bearing
the gear scratching is the fact that the clutch is not fully disengaging and there is still excessive torque in the input shaft for the syncro rings to work properly
fit a new clutch kit ( including new throwout bearing) before you have to rebuild the transmissionas well

Apr 01, 2017 | 2011 Mahindra Scorpio

1 Answer

Grinding noise after shifting


The clutch pedal need to be adjusted ,while you press the pedal clutch,it is not disengage fully the gear box that why when you shift it make that noise,well hope that clear your mind and help you.

Jan 28, 2010 | 1997 Honda CR-V

1 Answer

Clutch not fully disengaging


You have either air in your hydraulics which you need to bleed or else the clutch plates are worn/warped....here is the repair manual....
rate me if I've helped you. Thanks.
http://www.carlsalter.com/download.asp?fileid=075084077095049050053045050048048046040083088046077067088046069067088041095050048048049046112100102

Apr 03, 2009 | 2003 KTM SX 125

2 Answers

I have a whirpool dryer Mod#LER5620KQ1 the dryer makes a grinding noise when you turn the power on what can this possibly be


Check for metal shavings under the unit pull off the back cover. It seems like this can be one of a couple things. Bad main bearing, your clutch is not fully disengaging or the brake is not disengaging

Feb 18, 2009 | Dryers

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...