Question about Motorcycles

Open Question

The Anf will kick start 1 st time every time , but you can hear it click once when pressing the start button , also the gear indicator light neutral and first light up but not 2 nd 3 rd or 4th gear

There are 2 problems that i have with the Anf The first being Although the neutral and 1 st gear illuminates the 2 nd 3 rd and 4 th gear lights do not illuminate even though the gears select ok . The second problem being when you press the start button although a click is heard the bike will not do anything , the battery is good and it does start on 1 st kick everytime , any ideas please , Mike

Posted by on

  • mike evans
    mike evans Jan 03, 2014

    Thanks for the suggestions I have now sorted both problems , The 1 st was a seized starter which I replaced with a 2 nd hand one , I shall strip the old one later , and the gear indicator was a relatively simple repair by removing the forward chain sproket casing ( 2 bolts ) then remove the little black sensor unit ( 2 bolts ) inspect and clean the 5 small tabs , I had to put some solder on 3 terminals to build them back up and gently file them back level , to the sensor block , reassemble .

  • Gregg Mahin
    Gregg Mahin Oct 18, 2017

    Hi, Mike I would really love to help you with your bike question but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my mental telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on the word "COMMENT" below and provide this information in the box that will open and then click on the green comment box in the bottom right-hand corner after it posts I will receive an "ALERT" icon that will allow me to respond to your information. Good luck and have a wonderful day.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Benimur
  • 6966 Answers

SOURCE: Daytona 675 won't start

Hi,

Two possibilities:

  • starting relay. This could actually be bypassed/jumped to determine if the starter motor will turn:
  • starter motor. most likely carbon brush.
Just a start, do postback how things turned up or should you need additional information. Good luck and Thank you for using FixYa.

Posted on Nov 22, 2008

Ad
DickCanFixIt
  • 948 Answers

SOURCE: Honda Shadow 600 c won't start in gear after battery change

The kickstand switch is either bad or bent out of position. See if you can activate the switch manually. Does the bike run now? If so, the switch is bent out of position. If it still won't run, jumper the wires together until you can replace the switch.

Posted on Apr 11, 2009

  • 22 Answers

SOURCE: 2000 yamaha vstar 1100 custom. starter problem?

I had the same problem 2001 XVS1100 Custom
this is a starter issue Over time the starter on this bike twists when its under a load.
Look at the two bolts holding the starter on if they are not straight across then its twisted. turn starter back in line with a pair of big channel locks and try to start this should do the trick if this works i would recommend taking the two bolts out and bend them back straight or replace and reinstall starter this should fixya problem

Hope this helps ...............Jimmyfixya

Posted on Jul 08, 2009

  • 18 Answers

SOURCE: 2000 es300 lexus auto w overdrive button overdrive 4th gear not work

There isn't anything wrong with your car. This is perfectly normal. I have a 2000 ES300 as well as other people that I know and it operates in the same way. Overdrive doesn't mean the same thing for every car or transmission. In our case overdrive is simply a reference to the top gear which is 4th gear. When you switch overdrive off(which is depressing the button causing the O/D OFF dash light to illuminate,) the highest gear becomes 3rd because you turned 4th gear or overdrive off. The application scenario for this is usually mountainous terrain where a lot of uphill driving makes it more feasible not to up shift into 4th gear while ascending and descending. It will not switch back to overdrive or 4th gear until you re-engage it by turning the overdrive back on or repressing the button. Again, when the O/D OFF dash light is illuminated, overdrive which is 4th gear is off and the highest gear will then become 3rd. It will never shift into 4th gear while this light is illuminated or overdrive is off. When you press the button and the O/D OFF dash light is NOT illuminated overdrive is on and therefore it will shift into 4th gear as usual. This applies to all 97-2001 ES300's and probably any other car you drive tat exhibits this same type of change when overdrive is turned off.

Posted on Jul 22, 2009

  • 2841 Answers

SOURCE: 92 Accord Automatic shifting

Has anyone change the transmission fluid and used anything other than Honda ATF-Z1. If so, have the fluid/filter changed in this car and use only Honda Fluid. This is the only fluid that you can use in a Honda. Even if you have used the correct fluid an fluid/filter change may help. If that is not the case then I suggest you seek out a trusted professional.

Posted on Aug 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 VW Beetle diesel automatic


all cars have starter lock outs.
all. ( cept 1929 Ford A)
there are 2 locks, park lock out
and starter lock.
all A/T have a PRNDL switch that cuts the starter, in any gear.
so you dont run over muffy.
this is called the KEY line or ST or start line.
its very simple, in gear the KEY line is dead open
try cranking in Neutral with fresh contacts.
if the line has 12v cranking on forward side of switch and 0v
out the switch its bad, or your not really in P/N.
simple to a fault. its just a switch.

you hot wire the starter and it cranks, (ask)
this proves the starter works.
so the key line is dead.
The FSM covers this, as does how to calibrate the shift linkage


Jan 22, 2014 | 1991 Honda Accord

1 Answer

The neutral lite wont stay on , the foot lever is not allowing it to go to neutral


The neutral light won't stay on because the gearbox isn't in neutral. try rocking the bike backwards and forwards, kick the gears down as many time as you can (at least 6) and then try moving the gear lever up one until the bike moves freely backwards and forwards. Your bike should then start. It would be easier to identify any problems if you let us know the make and model of the bike.

Feb 11, 2013 | Motorcycles

1 Answer

How to drive?


you can ride the cluthch on a bike un like a car you wont hurt it its oil lubricated constantly, sitting on the bike pull the clutch in with your left hand and click the left foot lever down in to 1st, then learn how to click it back up 1 half movement in to neutral. the neutral light will come on sfter the bike enters neutral. in first gear give the throttle on the right hand a squeeze and pull the clutch in with your left hand put foot gear selector down in to 1 st and begin to release clutch slowly. hold on as bike will engage may be jerky balance yourself! when you get moving stop! by pulling the clutch in and the hand brake as you close the throttle to stop! practice your take off many times some where safe! when you get your balance in 1st gear pick up speed and begin shifting the foot gear selector up in to 2nd gear and practice closing the throttle and breaking to a safe stop. gears are generslly 1st down 1 click 2345 and6th all up from there and neutral is 1 half a click up from 1st between 2nd gear. And dont put it in gear with the kick stand down t may stall on you

hope this helps

May 03, 2011 | Honda CR 500 R Motorcycles

1 Answer

Cant push the button to put in gear


CHECK MAKE SURE BATTERY FULLY CHARGED IT HAS TO BE 12.5 VOLTS BEFORE THE BRAKE TRANSMISSION SHIFT INTERLOCK SOLENOID WORKS.IF BATTERY POWER GOOD CHECK BRAKE LIGHTS TO SEE IF BRAKE LIGHTS SWITCH IS WORKING.IF NO CHECK FUSE.IF FUSE GOOD BRAKE LIGHT SWITCH IS FAULTY. IT CONTROL THE BRAKE TRANSMISSION SHIFT SOLENOID ALSO THE NEUTRAL SAFETY SWITCH.IF FUSE AND BRAKE LIGHT SWITCH IS GOOD.YOUR PROBLEM COULD BE A FAULTY NEUTRAL SAFETY SWITCH OR BRAKE TRANSMISSION SHIFT SOLENOID FAULTY.

May 05, 2010 | 2001 Chevrolet Cavalier

1 Answer

NEED AQUALITE MANUAL - CAN'T SET TIME


To set time:

1) Press "Mode" button until Time is displayed.
2) Press and hold "Lap/RST" button until seconds display starts flashing.
3) Press "ST./STOP" button to change selected entry.
4) Press "Mode" button to change from seconds>minutes>hours>date>month>day of the week>time format>date format
5) Press "Lap/RST" once you are done to set the time.

To set Alarm time:

1) Press "Mode" button until ALM is displayed.
2) Press and hold "Lap/RST" button until minutes display starts flashing.
3) Press "ST./STOP" button to change selected entry.
4) Press "Mode" button to change from minutes>hours (remember to cycle through for AM or PM
5) Press "Lap/RST" once you are done to set the alarm.

To toggle alarm sounds on and off:

1) Press "Mode" button until ALM is displayed
2) Press "ST./STOP" button to toggle alarm sounds on or off (shown on display)
3) If alarm sound is shown on display, alarm will go off every day at the selected time. To turn off alarm once the alarm sounds, simply press any button on the watch.

Apr 09, 2010 | Watches

2 Answers

NEED THE INSTRUCTIONS FOR AN AQUALITE 100 jstreiter@comcast.net


To set time:

1) Press "Mode" button until Time is displayed.
2) Press and hold "Lap/RST" button until seconds display starts flashing.
3) Press "ST./STOP" button to change selected entry.
4) Press "Mode" button to change from seconds>minutes>hours>date>month>day of the week>time format>date format
5) Press "Lap/RST" once you are done to set the time.

To set Alarm time:

1) Press "Mode" button until ALM is displayed.
2) Press and hold "Lap/RST" button until minutes display starts flashing.
3) Press "ST./STOP" button to change selected entry.
4) Press "Mode" button to change from minutes>hours (remember to cycle through for AM or PM
5) Press "Lap/RST" once you are done to set the alarm.

To toggle alarm sounds on and off:

1) Press "Mode" button until ALM is displayed
2) Press "ST./STOP" button to toggle alarm sounds on or off (shown on display)
3) If alarm sound is shown on display, alarm will go off every day at the selected time. To turn off alarm once the alarm sounds, simply press "ST./STOP" button on the watch.

Mar 26, 2010 | Bulova Watch

1 Answer

How do you set the time?


To set time:

1) Press "Mode" button until Time is displayed.
2) Press and hold "Lap/RST" button until seconds display starts flashing.
3) Press "ST./STOP" button to change selected entry.
4) Press "Mode" button to change from seconds>minutes>hours>date>month>day of the week>time format>date format
5) Press "Lap/RST" once you are done to set the time.

To set Alarm time:

1) Press "Mode" button until ALM is displayed.
2) Press and hold "Lap/RST" button until minutes display starts flashing.
3) Press "ST./STOP" button to change selected entry.
4) Press "Mode" button to change from minutes>hours (remember to cycle through for AM or PM
5) Press "Lap/RST" once you are done to set the alarm.

To toggle alarm sounds on and off:

1) Press "Mode" button until ALM is displayed
2) Press "ST./STOP" button to toggle alarm sounds on or off (shown on display)
3) If alarm sound is shown on display, alarm will go off every day at the selected time. To turn off alarm once the alarm sounds, simply press "ST./STOP" button on the watch.

Jan 13, 2010 | Watches

1 Answer

Starter does not turn


chec fuses-bad ones can appear normal-inspec if connecs r tite at starter n solenoid area-n also relays--starter may be bad ur bike is 10yrs-test it--that electric clutch may be malfunctionin too

Aug 30, 2009 | 1999 Yamaha XVS 1100 Dragstar

1 Answer

Have a 2002 triumph sprint st 955i, bike would


Hi, the problem lays with your side stand switch. This is designed to stop us riding off with the stand down. When the switch plays up the safety still works with the stand up. Try giving it a good clean and spray with WD40. It gets covered in crud from the chain lube.
Tom

Jul 07, 2009 | 2002 Triumph Sprint ST

6 Answers

Aqualite stopwatch alarm


To set time:

1) Press "Mode" button until Time is displayed.
2) Press and hold "Lap/RST" button until seconds display starts flashing.
3) Press "ST./STOP" button to change selected entry.
4) Press "Mode" button to change from seconds>minutes>hours>date>month>day of the week>time format>date format
5) Press "Lap/RST" once you are done to set the time.

To set Alarm time:

1) Press "Mode" button until ALM is displayed.
2) Press and hold "Lap/RST" button until minutes display starts flashing.
3) Press "ST./STOP" button to change selected entry.
4) Press "Mode" button to change from minutes>hours (remember to cycle through for AM or PM
5) Press "Lap/RST" once you are done to set the alarm.

To toggle alarm sounds on and off:

1) Press "Mode" button until ALM is displayed
2) Press "ST./STOP" button to toggle alarm sounds on or off (shown on display)
3) If alarm sound is shown on display, alarm will go off every day at the selected time. To turn off alarm once the alarm sounds, simply press "ST./STOP" button on the watch.

Feb 11, 2008 | Watches

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...