Question about Pit Motorcycles

1 Answer

Repairing gongyu 125cc

I can not get clutch to ingage and now when i kick start it i have no compurstion

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

Hello Animal Charm, my name is Andres now let me explain you that the clutch is not engaging doesnt have nothing to be with the engine compression just kale sure the clutch cable is not broken or disconnected and abou the engine compression can be caused of so much trying to start the engine is drawn

Posted on Jan 03, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HUSQVARNA Z4824 O TURN MOWER - NOCKS WHAN PTO IS INGAGED & STALLS


need throttle adjustment govenor adjustment possiblt new pto clutch you have to take in to shop adjustmets 50.00 pto clutch 200.00

Sep 03, 2014 | Garden

1 Answer

I tried to add freon to my air conditioner but the gear won't kick in


make sure all the electrical plugs are free of corrosion and pluged in.it has to have a certain amount before the pump clutches will ingage the pump. pump could be bad also.

Jul 24, 2014 | 1999 Saturn Lw 4dr Wagon

1 Answer

Standard shift, v6, 3.2, and can't ingage shifter into gear. Replaced slave cylinder and master cylinder. Bleed unit, after starting it looses pressure on clutch pedal not allowing gear to ingage. With...


Sounds like you may have air trapped in the system.Try this trick.Remove the bleeder screw from the slave cylinder.Place your finger over the hole to act as a one way valve, allowing air and fluid to escape but not allowing air to get sucked back in.Then have someone stroke the pedal slowly making full strokes, keep an eye onn the resevoir so that it does not get low and fill the system with more air.If there is room turn a bottle of brake fluid upsidedown in the resevoir to keep it from running dry.After you have run a bottle of fluid through it replace the bleeder and pump and bleed the old fashioned way a few times.If there is air it should be gone.If clutch will still not disengage the something is wrong with clutch plate and or pressure plate.Good luck!

Mar 02, 2011 | 1992 Isuzu Trooper

1 Answer

Put car in reverse after car warms and it doesnt ingage until you push on the gas. It stays in the nuetral position


hi sound like the clutch is worn and your having to use the speed of the engine to help you ingage the gear.Does the clutch slip at all when driving in a forward gear ?

Sep 02, 2010 | 1993 Saturn SC2

1 Answer

WHEN TAKING OFF, MOTORCYCLE WILL NOT MOVE AFTER INGAGING CLUTCH LEVER!


2000 VN 1500 Vulcan has a good clutch system, a little dodgy but a good system. You may want to diagnose the issue first to check if it is just the level and the cable or the clutch line itself that needs to be taken care of.

First, loosen up the cable that the clutch lever will go halfway first before you feel the spring of the clutch kicking in. If this still did not give you drive, this means that you need to have your clutch checked as it may be worn out or the clutch wheel is broken that the release bearing no longer pushes the plate to the transmission.

Jun 17, 2010 | 2000 kawasaki VN 1500 Vulcan Classic...

1 Answer

Turning signal problems


Kick stand switch does not have ground installed.It's 2 cables comes straight from the ECU.Sounds like rust in your harness plugs.Unplug the all one by one and spray them with penetrating oil.Also check the Flasher relay by turning on either one of your turnong signals and hit the relay lightly to see if it will work.

May 29, 2009 | 1997 Yamaha YZF 750 R

1 Answer

My 1987 suzuki fa50 twistngo does not turn


The bit that ingages the kick start is half way along the rear hand break cable.
you can push it with your hand and kick it over.
also try re tensioning you brake cable
this can be done at two pionts along the cable at the end or on the balance bar (10mm spanner required)
This needs to be adjusted as the pads wear down.

Mar 04, 2009 | Suzuki Boulevard M50 Motorcycles

1 Answer

New Clutch well not ingage


I have run into this problem befor a customer brought in a car that he tryed to replace the clutch in and had the same issue unfortunatly the fix was to remove the clutch disc and flip it over as it is in wrong

Oct 09, 2008 | 2003 Hyundai Tiburon

2 Answers

Air condition


yes you can go to a parts store and buy2 cans of freon i belive they are called 134A and a adapter and recharge your air yourself for a total of about 40 bucks..

Sep 30, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pit Experts

micky dee

Level 3 Expert

2888 Answers

Gregg Mahin
Gregg Mahin

Level 3 Expert

43836 Answers

neil

Level 2 Expert

119 Answers

Are you a Pit Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...