Question about Honda Motorcycles

1 Answer

Xrm110 dose not kill the engine using ignition swicth

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.

  • Honda Master
  • 47,185 Answers

Hi, Anonymous for more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Ignition Switch Wires HELP Honda Elite 250
switch or kill switch will not shut engine off Page 1 iboats Boating...

Posted on Sep 08, 2017


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 6826 Answers

SOURCE: dj_relly999 ignition swicth fixed now

I looked at the starting/charging schematic and found the following:

There is a 10A Crank Fuse in the I/P Fuse Block.
There is a Start Motor Theft Deterrant Relay with YEL/BLK wire and YEL, PPL, and RED wire
There is a theft deterrant module with YEL/BLK wire.
There is an ignition switch, which you replaced, already.

I think the theft deterrant module is giving you problems
I could find no data on how the theft deterrant module can be programmed with the new key.
May have to go to dealer to have the new ignition key programmed to the computer or the theft deterrant module.

Good luck on this repair.

Posted on Oct 15, 2010

  • 3679 Answers

SOURCE: how do i put a kill swicth in the ignition wiring

follow this u-tube link and see if it helps
Transponder Chip Key Bypass How To For Any Car

Posted on May 14, 2014

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where dose hot wire go to from coils on la145 22hp v twin

the coil wire is only a kill wire. it goes through the wiring harness through safety switches back to the ignition switch.

Nov 10, 2016 | John Deere Garden

1 Answer

Xrm110 engine diagram

Hi, Anonymous for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Xrm110 engine diagram Google Search
Honda XRM 110 Wiring Diagram Schematic Diagrams
Honda Xrm 110 Service Manual

Feb 23, 2014 | Honda Motorcycles

1 Answer

Backfires and will not idle and goes fast and then slow

Hi sounds like fuel problem, try draining tank, check fuel filter for debris then refill with good quality fuel. Add a big dose of in tank fuel cleaner. Check spark plug[s] replace if necessary, spray ignition sealer/damp start around HT coil. Check air filter and clean as necessary. Make sure choke, if fitted, is working properly. Check ignition switch for water flush with WD 40 or similar then spray in silicon oil. Check engine kill switch is operating properly and has no water ingress.

Jan 28, 2014 | 1985 Honda XR 600 R

1 Answer

Turn key car starts fine turn key to shut car off and it dont shut off

that could be the ignition swicth when you turn the key to take it out its like a kill swicth to spot the spark plugs working. you might need a new barrel look for the key. just I think.

Launch X431 tools

Sep 27, 2013 | Mercury Grand Marquis Cars & Trucks

2 Answers

Dose not to strat can"t fine the kill switch

What kill switch ??
If the engine cranks but does not start, someone would need to figure out if you are missing spark to the plugs or fuel to the injectors to have a direction to troubleshoot.

Oct 08, 2012 | 2003 Kia Spectra

1 Answer

Problems with clutch and kill switch on crf230

Check that they haven't been shorted out. This is a common bodge when they become a pain in the buttocks.

Mar 17, 2012 | 2004 Honda CRF 230 F

1 Answer

Key switch on 1998 taurus

I would look for a direct short in your wiring harness. It sounds to me like the wires are shorted together under your dash or maybe even out by your starter. Look for a location that contains the ignition wires and the starting circut.

Nov 12, 2011 | 1998 Ford Taurus

1 Answer


i would put a tago swicth on my positive wire on the coil pack and just install the swicth inside somewere.that is what i did

Apr 10, 2010 | 1997 Honda Prelude

1 Answer

My ktm 105 isn't getting no fire .

you need a new ignition coil

Jan 09, 2009 | 2008 KTM 105 XC

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4727 Answers


Level 3 Expert

78257 Answers


Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides