Question about 2013 Kymco Downtown 300i

Open Question

Seat cable maintenance - 2013 Kymco Downtown 300i

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i install seats for 2001 chevy venture


Seats or covers? The seats front seats nd to be bolted in the back row of seats nd to install the back bar first then just drop the seats down they should lock into place

Jul 12, 2014 | 2001-2005 Chevy Venture Leatherette Seat...

1 Answer

How to remove passanger seat from bmw 2001 x5?


slide seat forward , undo rear bolts
slide seat back , undo front bolts
unplug electrics if any
remove seat

Jun 28, 2014 | Vehicle Parts & Accessories

1 Answer

I recently changed the front brakes on my 2009 Town and Country and now my brake light comes on. I did not use the special tool to seat the caliper piston. I used a c-clamp. Also, I didn't open up the...


Try and disconnect the ground cable on the battery for 10 minutes then connect it back. This reset the computer to take off the brake light....unless you have a malfunction.

Mar 05, 2014 | Vehicle Parts & Accessories

1 Answer

Transmission shifting


Make sure the transmission fluid is at the correct level. If this is not enough, perhaps adjusting the TV cable (throttle valve cable) will be necessary.

Nov 13, 2013 | 1993 Cadillac STS Ballistic Custom Seat...

1 Answer

MOTORCYCLE BATTERY DRAIN


Although rebranded, the OEM battery for most Japanese motorcycles is Yuasa. There are some maintenance free batteries for MCs now available. Maintenance free batteries do not have the clear plastic PVC hose lines. Batteries last about 4 years... when in doubt, replace it. Check your battery either under the seat or accessible from the plastic side fairing to see if it has a hose nipple on the battery. If it doesn't then the battery is a maintenance free type. If it has a hose nipple, buy a new clear plastic PVC hose from a service station (usually used for car windshield washers) or (better) pet shop (used for aquariums) and run a length down the frame until its clear of metal so the battery water can drip onto the pavement. Cable ties work great at securing it as you don't want the liquid dripping on anything except the ground.

Aug 27, 2012 | kawasaki Motorcycles

1 Answer

Changing pvc valve


1995 Geo Truck Tracker 4WD 1.6L TBI SOHC 4cyl
The PCV Valve is located under hood, center, upper engine area, top of engine, mounted in passenger side of intake manifold.

The low gas mileage and the versatility that your 1995 through 1999 Geo Tracker offers are two benefits of owning it. The maintenance needs to be kept up on your Geo Tracker. One form of this maintenance is to replace the valve cover gasket once you have driven 100,000 miles or more.
  1. Allow your engine to cool. Disconnect the negative battery cable. Remove the air inlet hose and air intake case or air cleaner housing. Detach the PCV valve hose from the PCV valve. Separate and remove the spark plug wires and the accelerator cable from their clips.
  2. Loosen and remove the valve cover bolts. Lift the cover up and off. Using a flathead screwdriver, gently nudge the gasket out of the gasket seating area. Using automotive engine cleaner and a clean cloth rag, clean the gasket seating area.
  3. Place the new gasket in the gasket seating area. Put the cover back into place. Put the bolts in and then using a torque wrench tighten them. Do not over tighten the bolts or the gasket will not fit correctly. Reconnect the spark plug wires and the accelerator cable in the holding clips.
  4. Reconnect the rubber hose to the PCV valve. Install the air intake case, or air cleaner housing, and the air inlet hose. Reconnect the negative battery cable. Add oil to the car and start the engine. Allow the car to run 10 to 15 minutes. This will allow the oil to lubricate the engine while it moves to the top.
I hope helps with this (remember rated this help) Good luck.

Dec 29, 2009 | 1995 Geo Tracker

1 Answer

What are the future problems of the BMW 650i?


The future problems? Now that really narrows down the possibilities. The biggest problem is running out of money once the warranty expires. The second biggest problem would be letting the wife or kids drive it.
Maintenance, maintenance, maintenance. These are very high maint. cars.
Electric seat motor and cables should go kaput. As will the drivers side electric window. The rear tailights will get water in them and quit. The oxygen sensor will quit leaving a check engine light on. The Bosch electric fuel pump IN the tank will quit as well, leaving you stranded. Get it replaced every 40-60 thou miles.

Nov 30, 2009 | 2006 BMW 6 Series

1 Answer

Phaser 860 maintenance tray A stuck


1. The Maintenance Drawer will not come out. - Often times this can be overcome by waiting 2 minutes for the ?Hot Ink? timer to expire, then remove the Maintenance Drawer. 2. If the printers Maintenance Drawer is locked in place and can not be removed and there are no cleaning functions currently taking place then the Maintenance Drawer can be unlocked by removing the right side cover and move the Cap/Wipe/Purge belts evenly down to the home position. This will raise the sensor flag from I/O Left and disengage the locking pin that is preventing the Maintenance Drawer from being removed. 3. If either Maintenance Drawer Guides (Blue Plastic Rail guides) have been replaced or removed and reinstalled and this is preventing the proper insertion of the Maintenance Drawer then check on the outside of the chassis frame that both rear locking tabs for the rail guides are protruding through the printers frame and are properly seated and notched into place. ? If they are not properly installed and seated then remove the rail guides and reinstall and then test for proper insertion and removal of the printers Maintenance Drawer. 4. Obstructions or spilled ink (wax) may be covering the Drum Maintenance rail guides and preventing the proper insertion or removal of the Maintenance Drawer. ? Check the printers Drum Maintenance Rail guides for any paper scraps or spilled ink or leaking ink from the Printhead. Make sure that there is no spilled ink under the Maintenance drawer waste tray and that it is seated properly. TROUBLESHOOTING TIPS AND HINTS: In order to provide more clearance when removing the printers Drum Maintenance rail guides, use the X-axis gear to move the Printhead away from the drawer guide that you are removing/installing. Also raise the Cap/Wipe/Purge assembly to reduce interference. When a drawer rail guide is mounted, double check its rear locking tabs where they go through the chassis side frame. Both blue tabs should be visible on the outside of the frame of the printer.

Apr 28, 2008 | Office Equipment & Supplies

Not finding what you are looking for?
2013 Kymco Downtown 300i Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...