Question about Gas Gas Motorcycles

Open Question

2008 wildfire scooter won;t start; getting fuel no manual avaialable; does it have a spark plug or electronic spark system

Replaced new trottle cable

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: peugeot 125 jetforce scooter 2003

aside from your air filter bein spotless and running the best possible tranny oil u need to take your carb off and clean out the jets, slide, float needle and the cylinder it slide up n down in, and the float bowl. also clean out the air boot and air box. if needed, a simple $115 self done top end job might be nececary, remember u have a 125 2 stroke, the most simplest of all man made machines, take advantage of such simplicity my man good luck

Posted on Feb 05, 2009

  • 3567 Answers

SOURCE: cant get my 50cc scooter to fire up-no spark. any

  • Do you see spark? If not, check the side stand kill switch. It kills the engine so that you don’t start out with the side stand down. If broken or out of adjustment, it would kill the spark. Check for a broken wire at the side stand switch and coupler. Try moving the side stand kill switch by hand. If that doesn’t work then wire a jumper around the switch to bypass it.
  • Is the handlebar kill switch on? Is it shorted out?
  • Check the fuses.
  • Check the operation of the ignition switch and all kill switches with a volt ohmmeter. Check the wiring harness. Did a wire come unplugged? Are all wires clean and with solid connections? Any abraded or pinched wires?
  • Is the bike in neutral and the neutral light is lit up? If no neutral light, check the neutral switch and neutral switch wire on center or side casing.
  • If still no spark, get CDI system and coils checked at the dealers shop.

Posted on Aug 14, 2009

MNfisherman
  • 11896 Answers

SOURCE: stock sym 125 scooter for almost 2 months not starting

check for fuel, spark, and air flow

Posted on Aug 30, 2009

  • 19 Answers

SOURCE: honda lead 100cc scooter wont start atall.changed

maby you have touched somthing on the carb when you changed the air filter or maby spark plug is to big or maby faulty try new one or your old one

Posted on Apr 13, 2010

  • 1 Answer

SOURCE: scooter wont start

i changed my spark plug and cleaned my carb/jets but my scooter still wont start can anyone help me?

Posted on Jul 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Roketa MC-75 will not start


Hi, Jerry and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the enrichner.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
14. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
15. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
16. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections loose, or connected to the wrong cylinders.
17. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
18. Faulty neutral, clutch lever, or kickstand safety switch.
19. Faulty fuel pump or fuse or relay.
20. A stuck bent or burnt valve.
21. Tilt sensor needs a reset.
22. Security system not disarming alarm needs a reset.
23. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Scooter Troubleshooting Scooter won start All about Scooters
http://www.extremescooters.biz/manuals/roketa_quick_start_guide.pdf
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
http://www.partsprousa.com/?vehicle_type=Scooter&brand=Roketa&brand_model=MC-75-150&srch=2#searcharea
Roketa MC 08 50 User Manual

Jul 04, 2017 | Roketa 150cc cheap Scooters

1 Answer

My Pulse Scout 49cc takes about 10 kicks to start in morning ok on electric start


Hi, Michael and the usual suspects are:
1. Spark plugs in bad condition or have an improper gap or are partially fouled.
2. Spark plug cables in bad condition.
3. Battery damaged or nearly discharged, should have 12.5 volts.
4. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Throttle controls not adjusted correctly.
6. Water or dirt in the fuel system.
7. Water or dirt in the carburetor.
8. Intake air leak.
9. Fuel tank vent hose and vapor valve plugged, or fuel line closed off, restricting fuel flow.
10. Enricher valve inoperative.
11. Engine lubricant to heavy (winter operation).
12. Ignition is not functioning properly (possible sensor failure).
13. Faulty ignition coil.
14. Valves sticking.
For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
Scooter Troubleshooting Scooter won start All about Scooters
Hard starting scooter 49ccScoot com Scooter Forums
Troubleshooting Your Scooter
http://www.scooterunderground.com/knowledge/manuals/documents/JetEuro50_Service_manual.pdf
Tao Tao 50cc Scooter Won Start SOLVED REPLACE CARBURATOR

Nov 18, 2016 | Motorcycles

1 Answer

I have a 2007 keeway hurricane and wont start


Hi, Brandon the following applies to carbureted also fuel injected models and the usual suspects are:
1. Severely discharged or damaged battery, 9 volts or lower.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Water or dirt in the fuel system, carburetor or filter.
11. Restricted, blocked or kinked fuel line.
12. Fuel tank empty.
13. Gas cap is not venting properly or fuel tank venting system blocked.
14. A failed fuel pump, pressure regulator and or fuel injectors.
15. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
16. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable free downloads that you need please visit the websites below. Good luck and have a nice day.
50cc keeway hurricane problems
Help Scooter won start cleaned carb which hoses
Scooter Troubleshooting Scooter won start All about Scooters
http://www.49ccscoot.com/manuals/Keeway_50cc_2T_Service_Manual.pdf

Feb 21, 2016 | Keeway Motorcycles

1 Answer

Hi I have a Baotian 50cc bt49q 9r. Bike won't start I've cleaned the carb drained old fuel etc, bought a new battery and a new spark plug.CDI might be faulty which I have ordered or the coil pack ?


Hi, Neil and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
8. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and module.
9. Spark plug cables in bad condition and shorting, cable connections loose, or connected to the wrong cylinders.
10. Ignition timing incorrect due to a faulty ignition coil, ignition module or sensors (MAP, CMP, CKP, O2 and/or BAS).
11. Security alarm needs a reset.
For more information about your issue and free downloads that you will need please visit the websites below. Good luck and have a nice day.
Scooter Troubleshooting Scooter won start All about Scooters
cranks but wont start
Tao Tao 50cc Scooter Won Start SOLVED REPLACE CARBURATOR
http://www.baotian-scooters.net/wp-content/uploads/2012/11/baotian-rocky-service-handleiding.pdf

Feb 01, 2016 | Motorcycles

1 Answer

I have a CPI Oliver sport, and I cant start it


Hi, Anonymous and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
8. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and module.
9. Spark plug cables in bad condition and shorting, cable connections loose, or connected to the wrong cylinders.
10. Ignition timing incorrect due to a faulty ignition coil, ignition module or sensors (MAP, CMP, CKP, O2 and/or BAS).
11. Security alarm needs a reset.
For more information about your issue and free downloads that you will need please visit the websites below. Good luck and have a nice day.
Scooter Troubleshooting Scooter won start All about Scooters
Tao Tao 50cc Scooter Won Start SOLVED REPLACE CARBURATOR
CPI motorcycle manuals
CPI Scooter Parts Racing Planet USA
CPI Oliver Sport 2011

Jun 10, 2014 | 2005 Cpi Oliver 50

1 Answer

Scooter won't start when hot


Hi, Janeway_rock and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the enrichner.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. A severely discharged or damaged battery, you need 12.5 volts or better and be able to pass a load test if necessary.
13. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
14. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
15. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections loose, or connected to the wrong cylinders.
16. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
17. Faulty neutral, clutch lever, or kickstand safety switch.
18. Faulty fuel pump or fuse or relay.
19. A stuck bent or burnt valve.
20. Tilt sensor needs a reset.
21. Security system not disarming alarm needs a reset.
22. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
ZUMAFORUMS NET View topic Scooter won start when hot
Scooter Troubleshooting Scooter won start All about Scooters
Yamaha XF50W Service Manual
OEM parts for Yamaha
Yamaha XC50Z Owner Manual

Apr 23, 2012 | 2007 Yamaha C3

3 Answers

I have a 2008 Wildfire Scooter 150cc. The carburator has an overflow tube coming out the bottom and gas just pours out of it when I try to start it. I have check all the tubes and the spark plug they seem...


My 150 carb has the same overflow and is stop by a needle vale screw is it there or missing replace the screw and it should run or plug the hose so it can not run out of the carb.

Sep 13, 2010 | Health & Beauty

1 Answer

My gator 150cc scooter is hard to start... i've replaced the spark plug,changed the oil,checked the fule filter,cleaned the air filter,changed the battery and checked all my hoses. having done all these...


Hi, Grippatl and the usual suspects are:
1. Spark plugs in bad condition or have an improper gap or are partially fouled.
2. Spark plug cables in bad condition.
3. Battery damaged or nearly discharged, should have 12.5 volts.
4. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Throttle controls not adjusted correctly.
6. Water or dirt in the fuel system.
7. Water or dirt in the carburetor.
8. Faulty fuel pump.
9. Intake air leak.
10. Fuel tank vent hose and vapor valve plugged, or fuel line closed off, restricting fuel flow.
11. Enricher valve inoperative.
12. Engine lubricant to heavy (winter operation).
13. Ignition is not functioning properly (possible sensor failure).
14. Faulty ignition coil.
15. Valves sticking.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Troubleshooting
Scooter Troubleshooting Scooter won start All about Scooters
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
http://www.partsprousa.com/
TaoTao 150cc Scooter Owners Manual

Jun 01, 2017 | Qianjiang QJ150 Motorcycles

1 Answer

I can't kick start my moped now. Before I can kick start it and sometime the engine goes out when I stop at the traffic.


Hi, Casper_c_rea and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
8. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and module.
9. Spark plug cables in bad condition and shorting, cable connections loose, or connected to the wrong cylinders.
10. Ignition timing incorrect due to a faulty ignition coil, ignition module or sensors (MAP, CMP, CKP, O2 and/or BAS).
11. Security alarm needs a reset.
For more information about your issue, please visit the websites below. Good luck and have a nice day.
Startup Troubleshooting Starting Your Scooter 1 7
How To Fix Scooter Starting Issues Part 1 Quick Guide
Fix Chinese 49cc Scooter that won start Benelli service manuals page 4
http://phano.xyz/yrt/b/benelli-owners-manual.pdf


Nov 24, 2009 | 2008 Benelli BX 570

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gas Gas Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Kim Halliwell

Level 1 Expert

32 Answers

Livewyre Studio
Livewyre Studio

Level 1 Expert

24 Answers

Are you a Gas Gas Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...