Question about 2006 Honda Xr 250

1 Answer

My indicators and speedo have stopped working

The fuses and relay are ok, ive cleaned the switch on the indicator but didnt work, the speedo is getting pwer but not counting km's or speed

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

Bad connection, unclip connectors, clean, and spray with wd42.

Posted on Dec 31, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MU-TH-R 182
  • 19 Answers

SOURCE: Right turn signal blowing fuse

Fuses are a SAFETY device. Never replace fuses with larger amp ones. Take the bike to an authorized repair shop and get it done right. There could be a short or relay problem that can lead to more extensive problems down the road. Safety devices are put in place to protect you and the system. Like in a home: if you run 14-2w/grd to light fixture the max fuse to use is 15amp fuse. never put a 20 in because the wire can melt at higher amps. Same with your bike. the wire is not rated to handel more than is was designed and fused for.

Posted on Feb 24, 2009

  • 330 Answers

SOURCE: Speedometer/indicator lights are not functioning

check for ground to these.ignition switch may need electrical cleaner spray.

Posted on Mar 22, 2010

  • 12 Answers

SOURCE: honda nsr 125 right indicator problem

check for a faulty ground wire/s, or a faulty or lose connection

Posted on Jul 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both my turn signals and emergency flashers stopped working


hi...
there is a relay which connects turn indicator and the emergency flashers which is provided for the timing of the flash.this timer relay may got burnt or damaged. even though the fuses are OK the turn indicators wont work. please check this.

please rate me weather the information which i provided was usefukll to you by clicking on the thumbs present on the end of your page.thank you

Jul 09, 2010 | 1999 Ford F350 Regular Cab

1 Answer

Renault kangoo indicators and hazard lights have stopped working, checked the fuses there ok. Could you help?


Most common cause is a failed indicator relay. Just swap it with a known good one to confirm whether it's faulty but ensure it's correctly rated for your Kangoo.

After that, the next most common causes are more expensive: the indicator switch and the hazard light switch.

Nov 01, 2009 | 2000 Renault 181

1 Answer

Turn signals wont work front or rear indicators in instrument pan


you need to check your fuses if fuses are ok locate indicator relay and check it has a live and a good earth if so open the relay and you should see a bad joint inside if this is the case you can either solder it back up or sometimes they are burnt out and need to be replaced if the relay is ok check the hazard switch

Aug 02, 2009 | 1996 Buick Regal Olympic Gold

1 Answer

Mercedes e 300


I think the hazards and the indicators function on different relays. If the indicator switch is working ok then the relay is probably not working.

Jul 18, 2009 | 1992 Mercedes-Benz E-Class

3 Answers

Indicators not self cancelling & Horn not working


I had the same problem. Horn not working and indicators not self cancelling.
After removing the steering wheel I found that the central two pronged collet, that engages with the steering wheel and drives the horn contact slipring and indicator cancellation, had worn down its prongs. this had caused the horn wires to stop rotating and they had been snapped by the motion of the steering wheel.
the ideal solution would be to replace the collet and horn wires but I managed to repair both

Apr 11, 2009 | 2000 Renault 181

Not finding what you are looking for?
2006 Honda Xr 250 Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...