Question about 2011 Yamaha FZ6R

1 Answer

FZ6R wiring diagram

Intended to replace the headlight bulb had to replace fairings to get to it. I took off headlight connector and put it back. Now no voltage to connector now. Fuse ok.

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Yamaha Master
  • 39,932 Answers

Hi, Anonymous for this scenario you will need your service/owners/ manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
2011 FZ6R wiring diagram Google Search
Anyone have wiring diagram
http://martin.lipinsky.cz/r6/files/LIT-11616-21-61.pdf
OEM parts for Yamaha
http://www.yamaha-motor.com/assets/service/manuals/2009/lit-11626-22-77_fz6r_1661.pdf

Posted on Dec 13, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

cape cod bob
  • 292 Answers

SOURCE: integrated tail problem

firstly ground them two wires and see what happens

you have got something screwed up if you gotta take fuses out to get stuff to work.

i find it easy if i draw what i have on paper first. you should have 3 wires for tail and 2 each for turns. those maybe 3 blacks, 1 green, 1 brown, 1 blue, 1 yellow.

http://www.carlsalter.com/motorcycle-manuals.asp

you can get a free download service manual here it will have the correct wiring diagrams for your bike. it shoudl help

Posted on Apr 05, 2009

  • 221 Answers

SOURCE: wire connector between stator & voltage reg/rectifier burnt

your voltage/reg. can be tested in a couple different ways check ground res. check res. then revs. bias on diodes you have ac in dc out it sounds like you may have a diode gone bad allowing ac curent to flow causing the wires to get hot

Posted on Jul 31, 2009

  • 8909 Answers

SOURCE: Just replaced the front fairing

Check for a good earth contact from the lamp, centre pin on the diagramme.

Posted on Mar 27, 2011

  • 5370 Answers

SOURCE: 1992 xj600- i replaced a faulty sparkplug cap and

The faulty regulator can cause this problem.Get the voltage at regulator checked.If its weak or shorting it can cause such problems. -------------- Also try this thing.Remove the main fuse for 5 minutes then reinsert it.The main fuse located near the battery compartment.Remove this main fuse, wait 5 minutes then re-0insert it then check.Many a times this reset the problem.But if that is not helping then get the regulator( alternator) checked.Also check the battery connections and ground.Anywhere its shorting or getting loose.--------This will help.Thanks.Helpmech.

Posted on Jun 19, 2011

alicantecoli
  • 22095 Answers

SOURCE: I took apart my headlight

i have a kawasaki 750 classic and on mine i had to change the headlight from RHD to LHD dip and i lost the connections as my friend was helping and as he took it out he dropped the headlight and all the little push in plugs come away but it wasnt difficult to sort out as i used my multi meter and turned the side light on first and found the feed then the indicators and so on till had one wire left and i couldnt find where it went so i shone torch on it and decided it had never been connected as it was all sort of dirty .Iam red/green colour blind so this is the only way i can do certain jobs like this .

Posted on Aug 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to see a diagram on how to replace headlight harness connector that is located inside the headlight on 2004 chrysler crossfire


Pull the rubber dust cover back you will see the electrical wires going to the bulb you can pull the old connector off from there it is not inside the housing, the bulb is held in by a small spring clip at the back of the bulb socket.

Sep 06, 2014 | 2004 Chrysler Crossfire

1 Answer

Headlight wiring diagrams


You can buy the replacement pigtail connector at the auto parts store the connector plugs on the back of the bulb inside the tube on the back side of the headlight box you remove the rubber dust cover and pull the old connector off the bulb plug in the connector on the pigtail and splice the wires to the old headlight wires all of this is done outside the headlight box there is no need to remove the headlight box.

Sep 05, 2014 | 2004 Chrysler Crossfire

1 Answer

Headlight wiring diagram


Honestly, there simply not much difficulty to the way headlights are wired on any vehicle. Standard headlights receive positive 12v from the headlight switch directly (or through a relay, if you have automatic headlights), and the switch receives power through the fuse block from the battery. When you turn the headlight switch on, you should get 12v at the input connector to your headlights. If the headlight connector is not receiving +12v at the connector when you turn the headlight switch on, check the fuse, the switch, and the relay. If the headlight assembly is receiving +12v at the connector, check the bulb. If the bulb tests good with an ohmmeter, check for a broken ground wire. That is simply all there is.

Jun 24, 2014 | 2000 Mitsubishi Galant

1 Answer

2000 wv jetta, one headlight is dim. it is not the bulb


This is caused by a poor headlight ground to the body of the car, the ground is most often found near the headlight under the hood, just follow the connector wires to the headlight bulb back through the wiring harness to locate it.

Jun 08, 2012 | Cars & Trucks

1 Answer

How to change the headlights?


Hi there, here are some few tips to assist you:
  • Remove the center cover and the screws attached to the radiator grille. Pull the radiator grille out of the engine compartment and set it on the ground.
  • Use a T30 Torx screwdriver to remove the two primary retaining screws from the headlight assembly. Make a note of each screw's original location--they're not interchangeable, so you'll need to put them back in the right slot to reassemble the light.
  • Draw the headlamp assembly away from the car and then disconnect the electrical wiring connector.
  • Release the wire clip on the back of the headlight assembly and remove the cover.
  • Disconnect headlight electrical connector and turn the bulb socket counterclockwise to remove it from the assembly. Install the new bulb, replace the cover and reattach the electrical connector.
  • Reconnect the headlight assembly wiring connector. Test the new bulb to make sure it works before replacing the retaining screws and radiator grille.
Hope these help. Please rate me if they do.

Jan 08, 2011 | 1999 Mercury Cougar

3 Answers

How do you remove the headlight assembly on a 05 Pontiac G6 GT to replace headlight bulb? When unlocking car, the bulb works, but when starting or putting car in drive light goes off. Is the bulb the...


real interesting... there should be no relation to the "drive" and the head light. current drawn by the starter causes the lights to go out or dim. Check the headlamp relay and for corrosion on connector to lamp assemblies in the engine compartment. On back of assemblies there is a large diameter plastic retainer after you remove the wire clip. Turn counter clockwise and pull back. a wire clip should retain the bulb itself

Oct 02, 2010 | 2005 Pontiac G6

1 Answer

Low Beam bulb replacement


you may have to remove top fairing get access

Apr 04, 2010 | 2002 Ducati 998 R

1 Answer

Do I need to remove my fairing to replace the headling bulbs?


Hi there,

well you can please follow the below steps -

Remove the Fairing - 1. Unscrew all seven outer fairing fasteners using a Torx driver. These screws are located on the inner fairing near the windshield, the speakers, and the handlebar clamps.
2. Stand in front of the motorcycle. Tilt the outer fairing toward you and hold it firmly. Reach in and disconnect the wire connectors for the headlight assembly by hand.
3. Move the fairing to a work bench to continue the procedure.

Change the Headlights - 1. Remove the wire harness connectors from the back of each headlight that need replacement. Turn the plastic retainer counterclockwise by hand to remove each bulb from its housing.
2. Install the new headlight bulb or bulbs, with each bulb's wider ears on the bulb back plates oriented toward the top. Screw in the plastic retainer rings by hand.
3. Connect the headlight wire harness connectors to the back of each headlight.
4. Move the fairing back to the motorcycle. Reinstall the fairing, battery and seat in reverse order.
Please post comments if you need more help or information.........

Good Luck!!

Thanks

Mar 17, 2010 | 2004 Harley Davidson FLTRI Road Glide

1 Answer

How to replace the headlight bulb on 2006 C280?


1. Figure out best way to light the tight area to see.
2.look directly behind the light headlight bulb under hood. You will see a round black plastic cover ...Pull it off. Remind yourself how it came off. It will hook into the bottom and snap back in nicely when you are finished.
3, Do NOT pull off wire connector yet. Note/feel how secure it is for when you replace new bulb.
4. On the outside perimeter of the backside of bulb housing you will see a black plastic round ring (this holds the bulb in)...(there are 2 finger tabs...one for clockwise, 1 for counter clockwise). There is hardly any play to either way...push gently Counter-Clockwise to allow bulb loose.
5. Pull Bulb with wires still attached straight out slowly and see how you will reinsert new one.
6. Have new bulb ready...don't touch bulb glass. Pull off wire connector.
7. Put new bulb on exactly same way onto wire connector
8. Gently house the bulb back the way it came in and hold flush.
9. Now push outer black plastic tab clockwise to hold in bulb...bulb should be as secure as before you took it out.
10.Test Light
11. Put on round black plastic back housing with hooks inserted into 2 two holes on the bottom and press top back its connector and you will hear a secure click.
12. You are done...have a beer...congratulate yourself. Tom.

Apr 18, 2009 | 2007 Mercedes-Benz C230 Sedan

Not finding what you are looking for?
2011 Yamaha FZ6R Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...