Question about Harley Davidson Motorcycles
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The codes are the following depending on your bike (EFI or Carb).:
P0373 CKP Sensor Intermittent Carb
P0373 CKP Sensor Intermittent EFI
P0374 CKP Sensor Not Detected Carb
P0374 CKP Sensor Synch Error EFI
U1255 Missing Message at Speedometer EFI
U1255 Serial Data Error/Missing Message EFI
U1255 Serial Data Error/Missing Message Instruments
U1255 Serial Data Error/Missing Message TSM/TSSM
this could be a number of potential things or maybe just a loose connection or ground somewhere. you are probably best to go to a shop, sorry.
Posted on Aug 14, 2009
Usually when you change the grips on the throttle side, depending on what type of replacement grips you bought, you'll be replacing the throttle sleeve as well. This means that you will be messing with the throttle and idle cables.
Loosen both cables at the adjusters as loose as they will go. Then, remove the two bolts that hold the right hand switch housing together. Carefully seperate the two halves. Do not damage the wires going to the switch. Work the throttle cable and the idle cable out of there slots in the throttle sleeve of the old grip. Be careful not to loose the brass ferrel that goes over the cable end. Lubricate the inside of the new throttle sleeve, the handlebar, and the area where the cables hook up with white lithium grease. Reassemble cables into new sleeve and reassemble the switch housing.
Once you have everything back together, adjust the throttle cable first and leave just a bit of slack in the cable. You should be able to freely "rock the throttle grip" before you feel the cable tighten up, Just a bit. Then adjust the idle cable about the same way.
Now, Turn the throttle cable to Wide Open throttle position and release it. It should "snap" shut, do this again from half and quarter throttle to make sure it works as it should. Failure to insure that the throttle operates properly can cause serious injury or death.
If you are simply replacing a grip on each side of the handlebar, use a long slender blade screwdriver or an ice pick to slide between the handlebar and the grip. Spray some WD40 in the work the grip a bit and it will break loose. Clean the throttle sleeve and handlebar off alcohol. Now, some people like to use "Grip Glue" on the new grips. Put the glue inside the grip and slide it up on the handlebar. If you put the glue on the handlebar, it will roll up in front of the grip as you slide it on to the handlebar or throttle sleeve. Make sure you "align" the two grips so they look the same before the glue sets.
Posted on Jul 18, 2010
Tips for a great answer:
Sep 26, 2016 | Motorcycles
Jan 27, 2013 | 2006 Harley Davidson FXDBI Street Bob
May 18, 2012 | 2006 Harley Davidson FXDBI Street Bob
Mar 28, 2012 | 2006 Harley Davidson FXDBI Street Bob
Mar 20, 2012 | 2006 Harley Davidson FXDBI Street Bob
Aug 12, 2011 | 2008 Harley Davidson FLHX Street Glide
Sep 04, 2009 | 2000 Harley Davidson FXDWG Dyna Wide Glide
Jul 07, 2009 | 2006 Harley Davidson FXDBI Street Bob
Mar 31, 2009 | 2006 Harley Davidson FXDBI Street Bob
Mar 17, 2009 | 2006 Harley Davidson FXDBI Street Bob
45 people viewed this question
Usually answered in minutes!