Question about 2004 Honda CBR 125 R

1 Answer

Brake light doesnt work of front brake but not the switch

The switch has been tested and its fine ive also tested the connections with a split pin and they are fine. what else could it be?

Posted by on

  • davidsonadri May 21, 2009

    the problem was the wiring to the fuse box

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 138 Answers

Check the socket that the bulb connects to.

Posted on May 19, 2009

  • Brittany Garner
    Brittany Garner May 21, 2009

    Why are you going to rate this inappropriate when I gave you something to check that you had not tested yet?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake light switch


Hi Jake, always check fuses and bulbs first for broken filaments. Then check the connection at the rear fender wiring harness, inspect for corroded, broken or loose pins. Use a dab of dielectric grease and repair as necessary. Check your brake relay if you have one , check your brake light switches for continuity, some models rear turn signals were single filament bulbs only, no running light. If all else fails get out your test light and start tracking the power wire from the harness connection. For a free wiring diagram please visit the website below and good luck:
Harley Davidson Wiring Diagrams and Schematics

Aug 06, 2013 | Harley Davidson Motorcycles

2 Answers

Amber flashing light GX620


LOL... If you haven't already fried your motherboard by using your modified PSU (And that's a big IF), then you need to buy a new PSU with similar specs and connection plugs (ie. a 24pin main) as the original PSU that came with the PC.

May 31, 2012 | Dell Computers & Internet

2 Answers

I have a 94 Chevy C1500 and the right side brake light and blinker are not working. The tail light and reverse light work though, and the right front blinker works but it blinks twice as fast as it...


It could be a bad multifunction (turn signal) switch. The way that switch works, it is possible that it can turn on the front blinker and not the rear one. It also cancels the brake circuit so the turn signal can work with the brake pedal depressed.

However, a more likely cause would be a break in the YELLOW/BROWN wire at the rear of the truck. It is common for the connector to get corroded at the left rear frame area where the bed harness connects to the vehicle harness. If you have trailer connections spliced into the wiring harness, these connections are also prime candidates for corrosion. I would look there first. Inspect these harnesses thoroughly all the way up and into the tail light assembly.

If the wires under the back of the truck look good, then I would check for power coming out of the turn signal switch. The wire at the turn signal switch is plain YELLOW (with no brown tracer). It is Pin (M) on the turn signal switch connector. The front signal is a LIGHT BLUE wire at the turn signal switch Pin (H). If you probe these with a test lamp, they should both work the same except the yellow wire will be hot with the brake pedal depressed and the switch NOT in the left turn position. If there is no power at the switch connector, replace the switch.

May 13, 2011 | 1994 Chevrolet K1500

1 Answer

I have an 86 volvo, brake lights were working then suddenly not. Ive checked bulbs, wiring. Tale lights work, headlights work, but no brake lights. Please help .....sincerely, girl that doesnt know...


It coould be the brake light switch, the wiring or the bulb failure relay under the dash. You will need a test light and a wiring diagram to find the problem. If you can get someone knowledgable about cars to help you, I can send you a wiring diagram.

Apr 05, 2011 | 1988 Volvo 240

2 Answers

I have a 1998 vw sharan tdi...the brake lights and led,s not working,fuses checked,bulbs checked all ok so i am at a loss as whats wrong...any advice would be great,thanks carol


Have the brake light switch checked. this switch is located at the top of brake pedal on the bracket, this switch is what controls the brake lights, if you look under the dash and follow the brake pedal up you will see the switch, a quick test is to remove the connector from the switch and jump the two connections on the connector not the switch and see if the lights work you may see a little spark thats okay, if lights come on with connector jumped then the switch is bad, heres a picture of the switch to help you locate it, hope this is helpful,johnjohn2_25.jpg

Nov 26, 2010 | 1993 Volkswagen Eurovan

1 Answer

2006 GMC Sierra The trailer park lights won't come on


Suspect 7 pin connector problem , you should have power on the 8pm positioned and the centre pin position as you look into the socket (on vehicle. These pins are both male pins as you look at them . If ok check trailer wiring where it splits for either lamp assy ! Good luck

Mar 09, 2010 | 2006 GMC Sierra 2500HD 2WD

2 Answers

Ford focus 2001 reverse light does not work, ive changed the bulb and checked the fuses and still does not work. the bulb i took out hasnt blown but is black on one side. can you help


I found that water had got into the connector and was damp so i took the bulb and casing out from inside the bumper disconnected it and sprayed the pins with WD40, connected it back up and it worked. took less than 5 mins.

Oct 19, 2009 | 2001 Ford Focus

2 Answers

O2 Dodge Dakota Brake lights wont work but bulbs r good.


If the bulbs are good I would suspect the Brake light switch.

Brake Light Switch: Testing and Inspection
The brake lamp switch can be tested with an ohmmeter. The ohmmeter is used to check continuity between the pin terminals.
Switch Circuit Identification
- Terminals 1 and 2: brake lamp circuit
- Terminals 3 and 4: RWAL/ABS module and Powertrain Control Module (PCM) circuit
- Terminals 5 and 6: speed control circuit
Switch Continuity Test
NOTE: Disconnect switch harness before testing switch continuity.
With switch plunger extended, attach test leads to pins 1 and 2. Replace switch if meter indicates no continuity.
With switch plunger retracted, attach test leads to pins 3 and 4. Replace switch if meter indicates no continuity.
With switch plunger retracted, attach test leads to pins 5 and 6. Replace switch if meter indicates no continuity.


27c4c52.jpg

Sep 11, 2009 | 2002 Dodge Dakota Club Cab

Not finding what you are looking for?
2004 Honda CBR 125 R Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Mike

Level 3 Expert

4339 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...