Question about 2004 BMW R 1150 R

1 Answer

Handlebar removal removal handlebar

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • BMW Master
  • 41,762 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Handlebar removal it is stuck


If the underside of the handlebar is stuck on the upper yolk after you have removed the four bolts, just give it a sharp rap with a rubber mallet from underneath. There is a knurled area that tends to bind but is there to assist clamping and prevent the bars from rotating in the clamp.

Sep 06, 2014 | BMW F 650 GS Motorcycles

1 Answer

How do i change handlebars on a 2010 Dyna


Unplug the handlebar wires where they connect to the wiring harness. Remove the black electrical connectors at the end of the wires. Pull the wires through the ends of the handlebars. Silicone lubricant sprayed into the bars will make this a bit easier, and you should be able to leave the silver pins on the ends of the wires, saving yourself some work when installing your new bars. Leave the wires connected at the handlebar controls when doing this. Just unscrew the controls from the bars and pull the wires.

Aug 21, 2012 | 2000 Harley Davidson FXD Dyna Super Glide

2 Answers

Adjust handlebar height on Schwinn Varsity


I'm answering 7 years later. I have a Schwinn Varsity 2500 Bike made probably in 2015. The Schwinn Varsity Bike is not set up the same way as a traditional bike. I loosened the center compression bolt and the two side stem clamp bolts and it came loose where I can adjust it up or down but, there's nothing to tighten the slack up below. I did some research. My original post here was to add or remove a spacer. I think you can remove a spacer to lower but, I don't think the stem is long enough to add another one. I've seen they sell an extension that you can add-on to make the handle bars higher.

Jun 25, 2012 | Schwinn Cycling

1 Answer

How to remove electrical harness to rewire changing handlebars


Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
Motorcycle Handlebars How to Install Internal Wiring Video Guide Tip of...

Jun 09, 2012 | Cars & Trucks

1 Answer

How to remove handlebar cover on FLHRC


Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
Adjust or Tighten Harley Road King motorcycle Handlebar

Jan 21, 2012 | Harley Davidson Motorcycles

1 Answer

How to change head set also replace front fork?


Loosen clamp at top of bike frame where seat slides in ...twist seat back and forth while lifting upward.......To remove ft. fork ..At handlebar assy.remove allen bolt..(some are hidden by rubber plug)..remove handlebar assy/remove large nut at top of frame where handlebar slides down in..
...twist and pull to remove front fork....some have upper and lower nut depending which bike.

Feb 27, 2011 | Cannondale Jekyll 600

1 Answer

How to change handle bars


HANDLEBAR REMOVAL

1. Remove maxi-fuse.


REMOVAL



1. Remove left side saddlebag.




2. Gently pull side cover from frame downtubes (no tools



required).



3. Depress latches on maxi-fuse holder and then slide



cover rearward to disengage tongue from groove in fuse



block cover.



4. Pull maxi-fuse from maxi-fuse holder.

2. Place blanket or protective cover over front of fuel tank to

protect against scratches or other damage.



FLHR/C/S:

Remove the handlebar clamp

(FLHR/C/S), NACELLE REMOVAL (FLHR/C), steps 1-

11, or NACELLE REMOVAL (FLHRS), steps 1-7.


WINDSHIELD/HEADLAMP NACELLE (FLHR/C/S) 2.31


WINDSHIELD REMOVAL
Standing at the front of the motorcycle,

use a finger to raise the wireform latch springs on


both sides of the windshield.


2. Gently pull on the top of the windshield until the upper


notches on the windshield brackets are free of the upper


grommets.


3. Carefully raise the windshield until the lower notches are


free of the lower grommets.


4. Remove windshield from motorcycle.


WINDSHIELD INSTALLATIONTo avoid scratching headlamp nacelle or auxiliary lamp


bracket, be sure that all four notches on the windshield


brackets are firmly seated on a rubber grommet.


1. Standing at the front of the motorcycle, carefully insert


the windshield brackets between the headlamp nacelle


and the auxiliary lamp bracket. Lower the windshield into


position until the lower notches on the windshield brackets


are seated on the lower grommets.


2. Gently push the top of the windshield toward the rear


until the upper notches fully engage the upper grommets.


3. Push down on the wireform latch springs, so that they


overhang the rubber grommets. If some adjustment is


necessary, loosen the retaining screws and rotate the


latch springs into the proper position.


NACELLE REMOVAL (FLHR/C)


1. Remove the windshield. See WINDSHIELD REMOVAL


on this page.


2. Remove the Phillips screw at the bottom of the headlamp


door (chrome ring). Remove the headlamp door.


3. Remove the eight Phillips screws to free the headlamp


housing from the headlamp nacelle.


FLTR:

Remove the instrument nacelle.

UPPER FAIRING/WINDSHIELD (FLTR), INSTRUMENT

NACELLE, REMOVAL.

FLHT/C/U:

Remove the fairing cap.

Remove the outer fairing as follows:


a. Standing at the front of the vehicle, use a T27 TORX


drive head to remove the three outer fairing screws


(with flat washers) just below the windshield.


b. Moving to the inner fairing side, remove the two fairing


screws just above the wind deflectors on the left


and right side.


c. Turn the handlebar to the right and remove the outer


fairing screw reaching in below the left side of the


fairing cap. Turn the handlebar to the left and


remove the fairing screw below the right side of the


fairing cap.


d. Tilting the outer fairing toward the front, squeeze the


two external tabs to remove the wire connector at


the back of the headlamp assembly.


e. Lift the fairing (with headlamp assembly) off the


motorcycle.Since the outer fairing screws hold the windshield in


place, the windshield may fall to the floor if not removed.


UPPER FAIRING/WINDSHIELD (FLHT/C/U), FAIRING

CAP, REMOVAL. Remove the radio (or storage box).



4. Remove the left and right handlebar switch controls..

5. Remove upper handlebar clamp screws (with flat washers).

Remove upper handlebar clamps and handlebar.

HANDLEBAR INSTALLATION


Just reverse for install. This is all from the maunual and I hope it helps you.



Nov 25, 2010 | 2005 Harley Davidson FLHTC - FLHTCI...

1 Answer

How to get acsess to my handlebars to tighten


You must remove the Nachele to get to the handlebar risers. They are bolted through the top triple tree. Of course, you must also remove anything that prevents you from gettng the nachelle off such as windshield, fairing, and headlight. Note: Sometimes if you turn the front end fully to one side, you and get to the large nut or bolt from the bottom side without removing he nachelle. Turn the front end to the other direction to get to the other nut or bolt.

Now, keep one thing in mind, the handlebar risers are mounted in rubber bushings. This is done to reduce handlebar vibration. Harley has used this vibration dampening system for years on their big twin bikes. Your handlebars may not be "loose" but move due to the rubber mounting. Before I went to tearing my bike apart, I'd feel of some other bikes handlebars first and compare it to what yours feel like.

You can get more firm bushings for the handlebars. Matter of fact, you can get steel bushings that eliminate the rubber mounting.

Go to this site and check out page 990
http://www.vtwinmfg.com/Catalog1/VTwinCatalogIndex1.htm It is the V-Twin manufacturing catalog and shows the handlebar riser bushings. Good Luck

Jan 31, 2010 | 2005 Harley Davidson FLHT - FLHTI Electra...

Not finding what you are looking for?
2004 BMW R 1150 R Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

phil cuzins
phil cuzins

Level 2 Expert

79 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...